a3c721772e
stm32/boards: Add stm32h743_af.csv file describing H7 GPIO alt funcs.
2018-03-09 14:06:34 +11:00
0b88a9f02e
unix/coverage: Allow coverage tests to pass with debugging disabled.
2018-03-08 12:49:31 +11:00
250b24fe36
stm32/boards/NUCLEO_F767ZI: Update pins list to include 3 extra pins.
2018-03-07 18:53:02 +11:00
bda3620616
stm32/boards/stm32f767_af.csv: Add ADC column to pin capability list.
2018-03-07 18:40:06 +11:00
024edafea0
stm32/i2c: On F4 MCUs report the actual I2C SCL frequency.
2018-03-07 14:59:03 +11:00
478ce8f7e3
esp32/modnetwork: Implement status('stations') to list STAs in AP mode.
...
The method returns a list of tuples representing the connected stations.
The first element of the tuple is the MAC address of the station.
2018-03-05 17:59:19 +11:00
d4470af239
esp32: Revert "esp32/machine_touchpad: Swap pins 32 and 33."
...
This reverts commit 5a82ba8e07
2018-03-05 14:06:45 +11:00
b691aa0aae
esp8266/esppwm: Always start timer to avoid glitch from full to nonfull.
...
The PWM at full value was not considered as an "active" channel so if no
other channel was used the timer used to mange PWM was not started. So
when another duty value was set the PWM timer restarted and there was a
visible glitch when driving LEDs. Such a glitch can be seen with the
following code (assuming active-low LED on pin 0):
p = machine.PWM(machine.Pin(0))
p.duty(1023) # full width, LED is off
p.duty(1022) # LED flashes brightly then goes dim
This patch fixes the glitch.
2018-03-05 11:39:44 +11:00
adda38cf76
stm32/qspi: Add hardware QSPI driver, with memory-map capability.
...
It supports the abstract QSPI protocol defined in drivers/bus/qspi.h.
2018-03-03 00:17:08 +11:00
8bd0a51ca9
stm32/spibdev: Convert to use multiple block read/write interface.
...
The spiflash driver now supports read/write of multiple blocks at a time.
2018-03-03 00:13:15 +11:00
861080aa3d
stm32/storage: Add option for bdev to supply readblock/writeblocks.
...
If the underlying block device supports it, it's more efficient to
read/write multiple blocks at once.
2018-03-02 23:57:53 +11:00
0210383da5
stm32/spibdev: Add option to configure SPI block dev to use QSPI flash.
...
To use QSPI (in software QSPI mode) the configuration needed is:
#define MICROPY_HW_SPIFLASH_SIZE_BITS (n * 1024 * 1024)
#define MICROPY_HW_SPIFLASH_CS (pin_x1)
#define MICROPY_HW_SPIFLASH_SCK (pin_x2)
#define MICROPY_HW_SPIFLASH_IO0 (pin_x3)
#define MICROPY_HW_SPIFLASH_IO1 (pin_x4)
#define MICROPY_HW_SPIFLASH_IO2 (pin_x5)
#define MICROPY_HW_SPIFLASH_IO3 (pin_x6)
2018-03-02 23:55:45 +11:00
a0dfc38641
stm32/spibdev: Update to work with new spiflash driver.
2018-03-02 23:55:40 +11:00
c607b58efe
tests: Move heap-realloc-while-locked test from C to Python.
...
This test for calling gc_realloc() while the GC is locked can be done in
pure Python, so better to do it that way since it can then be tested on
more ports.
2018-03-02 10:59:09 +11:00
c3f1b22338
tests/unix: Add coverage tests for various GC calls.
2018-03-01 22:49:15 +11:00
d3cac18d49
tests/unix: Add coverage test for VM executing invalid bytecode.
2018-02-27 16:18:11 +11:00
c5fe610ba1
esp8266/modnetwork: Implement WLAN.status('rssi') for STA interface.
...
This will return the RSSI of the AP that the STA is connected to.
2018-02-26 16:41:13 +11:00
01dcd5bb71
esp8266/uart: Allow to compile with event-driven REPL.
2018-02-26 16:10:27 +11:00
62be14d77c
tests/unix: Add coverage tests for mpz_set_from_float, mpz_mul_inpl.
...
These new tests cover cases that can't be reached from Python and get
coverage of py/mpz.c to 100%.
These "unreachable from Python" pieces of code could be removed but they
form an integral part of the mpz C API and may be useful for non-Python
usage of mpz.
2018-02-25 23:43:16 +11:00
989fc16162
stm32: Move MCU-specific cfg from mphalport.h to mpconfigboard_common.h.
...
It's cleaner to have all the MCU-specific configuration in one location,
not least to help with adding support for a new MCU series.
2018-02-23 16:54:07 +11:00
ea05b400df
stm32/flash: Use FLASH_TYPEPROGRAM_WORD to support newer HALs.
2018-02-23 16:30:47 +11:00
e6220618ce
stm32: Use "GEN" for describing files generated in the build.
...
Instead of "Create", to match the build output from the py/ core.
2018-02-23 16:27:30 +11:00
60b0982bb2
stm32: Add board config option to enable/disable the ADC.
...
The new option is MICROPY_HW_ENABLE_ADC and is enabled by default.
2018-02-22 14:22:45 +11:00
a36c700d9b
minimal/Makefile: Explicitly include lib/utils/printf.c in build.
...
The bare-metal port needs it and it's no longer included by default since
the Makefile now uses $(PY_CORE_O).
2018-02-22 13:19:09 +11:00
9df6451ec5
ports/{bare-arm,minimal}/Makefile: Only build with core source files.
...
These ports don't need anything from extmod so don't include those files
at all in the build. This speeds up the build by about 10% when building
with a single core.
2018-02-22 12:48:51 +11:00
Damien George
sec2
Lee Seong Per
Olivier Ortigues