When SRST is never enabled, the global jtag_srst variable is left at its
initial state, that is, -1, and it does _not_ mean SRST is currently
asserted. Same about TRST.
Fixes "reset halt" in cases when srst_pulls_trst but srst usage is not
enabled.
Change-Id: I8d2e9120479de4cfbf5561033926c9ef945eecc9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3943
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 77a1c01ccb introduced infrastructure
for utilizing protection blocks of different size than erase sector.
Parts of doc/help kept reading 'sector' instead of 'protection block'.
flash_driver_protect() parameter range testing did not switched
to bank->num_prot_blocks.
This change fixes it.
Change-Id: Iec301761190a1a1bcc4cb005a519b9e5e4fede51
Reported-by: Mark Odell <mark@odell.ws>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3917
Tested-by: jenkins
Reviewed-by: Mark Odell <mrfirmware@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Don't terminate the transaction end-check early if debug power-loss
was detected, without clearing SSTICKYERR.
Change-Id: I83b6a4a20523eea42e48a15297f972a730aa21a8
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3947
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
These libraries override the used CFLAGS without adding the
defaults. This didn't have any effect until change
http://openocd.zylin.com/3870 (ef4c139). Restore by adding
AM_CLAGS to the per-target CFLAGS.
Interestingly, automake seems to clear the CFLAGS for the target
even if the override variable is only mentioned within a non-active
conditional branch, such as the IS_MINGW for the affected libraries.
Change-Id: I805206865e59e3fa33a7ea3c0d3472e51219351c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3927
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Fix build failure when libusb dev files are not available and
so usb_blaster is disabled.
Change-Id: I4cda7df689cdb4b62b733cbbab813241cf561e29
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3920
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This was never used and produces warnings on some systems.
Change-Id: I48d2c5b79890bb2d70c5fae95278b8eb62743398
Reported-by: Tommy Murphy <tm1234@users.sf.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3891
Tested-by: jenkins
OpenOCD doesn't (yet) know how to handle HYP mode properly so spsr
register is not getting initialised when OpenOCD connects to a target
stopped in this mode.
Reported on IRC by thinkfat and nearffxx.
Change-Id: I4bda9ba0c582c8e9cacefe708cc4a3d947151f84
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3906
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Chengyu Zheng <chengyu.zheng@polimi.it>
Add a helper to hide the platform-dependent method to get a
canonical, absolute, /-separated path to the executable.
Use this and the relative path from BINDIR to PKGDATADIR to
construct a search path that finds the scripts even if the
installation dir is moved, as long as the structure below $prefix
is maintained.
This method should fully support all the tricks you can to with
autotools to customize the installed layout such as overriding the
default directories at configure-time and overriding the configured
directories at build-time.
The exe path detection methods are combined from
http://openocd.zylin.com/3388 by Rick Foos and
http://openocd.zylin.com/3537 by Steven Stallion, as well as tips
found all over internet.
Change-Id: Ifc9cc9dd0bf52fbd67b1b0f2383318cda0c422c4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Steven Stallion <sstallion@gmail.com>
Reviewed-on: http://openocd.zylin.com/3889
Tested-by: jenkins
Reviewed-by: Rick Foos <rfoos@solengtech.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The changes since the last update are mainly related to the build
system, preparations and cleanups for the upcoming release.
If there are no bugs reported, this will be the last update before the
libjaylink 0.1.0 release.
Change-Id: I4cec9bb61159f6153690aaf39c1d12ba0baacf9b
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3886
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
EMUCOM is a way to communicate with a J-Link device via so called
channels. A channel can either be read or written in a single
operation.
Beside the reserved channels for SEGGER, there are channels available to
implement vendor and/or device specific functionalities. For example,
EMUCOM is used on many starter and development kits from Silicon Labs to
access power measurements and various other information and settings.
Change-Id: I6094109c043b34aed4a40ceabe71f30ff896bf1d
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3794
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The current implementation fails on devices with less than 32k of
flash (such as several devices in the Zero Gecko family) because
the 'assert' assumes (incorrectly) that the number of flash banks
will always be >= 32.
This change ensures that at least one word of lock bits is always read
in order to support devices with less than 32k of flash.
Signed-off-by: Kevlar Harness <software@klystron.com>
Change-Id: I59febe2cb690c893a5057a5f72918e146cf2afe4
Reviewed-on: http://openocd.zylin.com/3806
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Avoid special rules to generate array at compile time by shipping
the generated file. Convert to Makefile build like the other
loaders.
Change-Id: I5a05edddcfaff3d395086cd3aa33120f8a7aa9dc
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3864
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change b0698501b0 fixed
reset for i.MX6 and TI Sitara SoCs but broke reset for
cortex-a targets that use SWD. This patch is a work-
around that forces asserting SRST when SWD is used.
Change-Id: I7e39f2a469b9b4b2b74ad48ba49f2eeb58528921
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3641
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a Cortex-M private configuration option
that allows setting the acess point during target
creation. This circumvents situations in hybrid systems
when the correct access point can not be automatically
detected.
Change-Id: If313a5250e6e66509bb9080f3498feab7781dced
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3639
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The Cypress CY7C65215 Dual Channel USB-Serial Bridge Controller [1]
understands the OpenJTAG protocol over a proprietary USB interface.
This patch adds support for the CY7C65215 to the openjtag interface
driver. A new configuration option, `openjtag_variant`, allows to
select the transport to use.
Libusb (1.x or 0.1) is now a hard dependency of the openjtag driver.
This should not be a big issue as libftdi also depends on it.
[1] http://www.cypress.com/?rID=82870
Change-Id: I55ffb3fd9e006eb311e405d9fb836bb119644bfd
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-on: http://openocd.zylin.com/2805
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Simplify hexify() and do not longer use 0 as special case for the
parameter 'count' to determine the string length of the binary input.
Instead, use strlen() outside of the function if needed.
Additionally, fix the return value and return the length of the
converted string. The old function always returned 2 * count.
Also, use more appropriate data types for the function parameters and
add a small documentation.
Change-Id: I133a8ab786b8f7c1296afcaf9c0a0b43881e5112
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3793
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Both the drive strength and slew rate are currently set to very high
values. This causes the waveforms to overshoot and be less reliable
when operating at high speed.
This patch lowers the slew rate and sets the drive strength to 4ma,
improving the waveform output.
Change-Id: I761d35cd64bc54a9e94043904ef00a003b056af0
Signed-off-by: Sean Cross <sean@xobs.io>
Reviewed-on: http://openocd.zylin.com/3707
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Philipp Guehring <pg@futureware.at>
