The code that takes only sections marked PT_LOAD is in
image_elf_read_headers in src/target/image.c
(Just trying to save some time for the next person with same question.)
Change-Id: I493c102c908fca2b7238276ddbbecbe8c7cd9a0a
Signed-off-by: Alexei Colin <ac@alexeicolin.com>
Reviewed-on: http://openocd.zylin.com/2348
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
TI's ICDI adapter supports some additional commands which a user might
want to run for debugging or other purposes, the most useful of them
being "debug unlock" that fully mass-erases the device and unprotects
the flash.
Change-Id: I26990e736094367f92106fa891e9bb8fb0382efb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2263
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
There were two problems with the _protect() feature:
1. The address written was off by a factor of two because the address
register takes 16-bit rather than 8-bit addresses. As a result the
wrong sectors were (un)protected with the protect command. This has
been fixed.
2. The protection settings issued via the lock or unlock region commands
don't persist after reset. Making them persist requires modifying the
LOCK bits in the User Row using the infrastructure described below.
The Atmel SAMD2x MCUs provide a User Row (the size of which is one
page). This contains a few settings that users may wish to modify from
the debugger, especially during production. This change adds commands
to inspect and set:
- EEPROM size, the size in bytes of the emulated EEPROM region of the
Flash.
- Bootloader size, the size in bytes of the protected "boot" section of
the Flash.
This is done by a careful read-modify-write of the special User Row
page, avoiding erasing when possible and disallowing the changing of
documented reserved bits. The Atmel SAMD20 datasheet was used for bit
positions and descriptions, size tables, etc. and testing was done on a
SAMD20 Xplained Pro board.
It's technically possible to store arbitrary user data (ex: serial
numbers, MAC addresses, etc) in the remaining portion of the User Row
page (that is, beyond the first 64 bits of it). The infrastructure used
by the eeprom and bootloader commands can be used to access this as
well, and this seems safer than exposing the User Row as a normal Flash
sector that openocd understands due to the delicate nature of some of
the data stored there.
Change-Id: I29ca1bdbdc7884bc0ba0ad18af1b6bab78c7ad38
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2326
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reference code for the SAMD2x disables caching in the NVM controller when
issuing NVM commands. Let's do this as well to be consistent and safer.
Add a "chip-erase" for the Atmel SAMD targets that issues a complete Chip Erase
via the Device Service Unit (DSU). This can be used to "unlock" or otherwise
unbrick a chip that can't be halted or inspected, allowing the user to reflash
with new firmware.
Add a "set-security" command which issues an SSB. Once that's done and the
device is power-cycled, the flash cannot be written to until a "chip-erase" is
issued. The chip-erase cannot be issued by openocd at this time because
the device will not respond to a request for the DAP IDCODE.
Change-Id: I80122f0bbf7e3aedffe052c1e77d69dc2dba25ed
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2239
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove this underutilized feature. Despite the fact that a lot of configs
specifies a arbitrary "variant", only the xscale target actually defines
any.
In the case of xscale, the use of -variant is dubious since
1) it's used as a redundant irlen specifier,
2) it carries a comment that it doesn't really need it and
3) only two xscale configs even specify it.
If there's a future target that needs a variant set, a target specific
option could be added when needed.
Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2283
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The hla_serial command allows for a programming device serial number to be
specified in addition to USB VID/PID. This allows for multiple ST-LINK/V2
programmers to be attached to a single machine and operated using openocd.
Change-Id: I350654bf676eb26ba3a90450acfa55d2a5d2d791
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/2198
Tested-by: jenkins
Reviewed-by: Martin Glunz <mg@wunderkis.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds -alias|-nalias options to ftdi_layout_signal command that
allow to declare a new signal based on an already defined one.
Change-Id: I552578ebcd12ae21957a1c0d3b7e878adeff6df0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2181
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Adds support for auto-probing on devices which support the IAP
Read Part ID command. Includes IDs for all LPC17XX, LPC13XX,
LPC11XX and LPC11XXX devices with publicly available user
manuals.
To use auto-probing, select the 'auto' lpc2000 variant.
Change-Id: Ic617c32925c9ebe0e9d9192ed8ddbfa08e9f0aaa
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/2075
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
LPC11(x)xx and LPC13xx devices are mostly compatible with the lpc1700
variant of the LPC2000 driver, but use a fixed flash sector size of 4KB.
Change-Id: I033515f4ff6bc61d3b9babd27096f78c99cea927
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/2071
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This introduces a new global Tcl procedure that is run just after
init_targets and before init_boards.
Its default behaviour is to assign gdb-flash-erase-start and
gdb-flash-write-end to reasonable defaults.
The rationale for doing "reset init" before gdb erases and flashes
memory is that all flash drivers are written in assumption that they
can safely be used only after chip reset (plus chip-specific
configuration in the init handler if any). The need to use "reset
halt" after flashing is because a user expects running firmware after
loading to be the same as running it from power-on-reset.
Change-Id: I9ddc4047611904ca4ca779b73376d2739611948a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2062
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should provide enough information to start using OpenOCD RPC.
I've seen some other example clients in different languages but I
can't find them anymore, and their legal status was unclear.
Change-Id: I3a95fe361d773040d1e52a62f9cc0cc655019a9f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1915
Tested-by: jenkins
Reviewed-by: Andreas Ortmann <ortmann@finf.uni-hannover.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Also add missing entries for JTAG-lock-pick Tiny 2, Xverve Signalyzer
LITE and default FTDI VID:PIDs.
Change-Id: I41b4f15409642298d1cf134d1f8014dc8f003005
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1969
Tested-by: jenkins
Intel Quark X10xx SoC debug support added
Lakemont version 1 (LMT1) is the x86 core in Quark X10xx SoC
Generic x86 32-bit code is in x86_32_common.c/h
Change-Id: If2bf77275cd0277a82558cd9895b4c66155cf368
Signed-off-by: adrian.burns@intel.com
Reviewed-on: http://openocd.zylin.com/1829
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The argument 'force' enables a user to bypass the internal cache and read
a target register directly. However it is missing from the user guide.
Change-Id: I26f689eec20b38a0dc5294626b25df566b554446
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1897
Tested-by: jenkins
By default the driver will now auto detect attached adapters, it does not
use an internal list any more. Update docs to match this.
Change-Id: I62a9d243cd236a8cf54cbd9d088c4837a8df31bf
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1902
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Changes solely to the Tcl Scripting API chapter of the UG:
* Some grammatical cleanup
* Fix formatting issues (@example and @verbatim formatting)
* Add references to missing OSes OpenBSD, NetBSD and eCos.
Change-Id: I3ec1a192a0b1e0a207dceb76fd39008d01e287a5
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1872
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
More cleanup from some of the later chapters from the User's Guide,
no functional changes.
Change-Id: Ib2860fc2574503e8107935d79db45fa96014fe3a
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1863
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove a tip describing the discouraged use of TAP numbers, and how
these numbers would be removed by mid-2010.
Change-Id: Iebe7e2e4a0f8e1f18a91d7935588dd9ced2b398d
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1862
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
