The _targets has to be global as it is accessed at the end of this file.
This is already the case for setup_a5x {}, assure it is the same way for
setup_crx{} . Without this change, the _targets at the end of this file
is empty in case the Cortex-R is the boot core, fix this.
Change-Id: I4979e3125ec7d93bbd56eee0096ae1d9c5f6a565
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8470
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Adds initial support for the BL702 series of chips, BL702, BL704 and BL706.
No flash bank support yet.
File name bl702.tcl was chosen over bl70x.tcl, because Bouffalo Lab
uses bl702 to mark the whole series in many of their tools.
The ndmreset bit in the RISC-V Debug Module isn't implemented correctly,
so it doesn't trigger a system reset as it should.
To solve this problem, the software reset is implemented
in the reset-assert-pre hook, which uses best reset method I could find.
What is not reset is the GLB core, which handles GPIOs, pinmux, etc.
The reset mechanism has been extensively tested, and works correctly
for both "reset run" and "reset halt", which the latter
halts very early in the BootROM.
Change-Id: I5ced6eb3902d1b9d9c1bba56f817ec5dc3493cb0
Signed-off-by: Marek Kraus <gamelaster@outlook.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8407
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Direct memory driver swd native configuration for am62a7, am62p and
J722S SoCs. All three share common memory map for the debug address
map, so there is a strong reuse. However, introduce board file
specific to the board to allow users to directly get started.
Change-Id: I5609925a2e9918fd4c91d9fd40fbee98de27fdbc
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8283
Tested-by: jenkins
Reviewed-by: Vaishnav M A <vaishnav@beagleboard.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The flag '-coreid' is used by the command 'target create' to
specify the debug controller of the target, either in case of a
single debug controller for multiple CPU (e.g. RISC-V harts) or
in case of multiple CPU on a DAP access port (e.g. Cortex-A SMP
cluster).
It is also currently used to specify the CPU ID in a SMP cluster,
but this is going to be reworked.
This flag has no effects on Cortex-M; ARM specifies that only one
CPU Cortex-M can occupy the DAP access port by using hardcoded
addresses.
The flash driver 'psoc6' uses the flag '-coreid' to detect if the
current target is the Cortex-M0 on AP#1 or the Cortex-M4 on AP#2
in the SoC.
There are other ways to run such detection, without using such
unrelated '-coreid' flag, e.g. using the AP number or the arch
type of the target.
Use the arch type to detect Cortex-M0 (ARM_ARCH_V6M) vs Cortex-M4
(ARM_ARCH_V7M).
Drop the flags '-coreid' from the psoc6 configuration file.
Change-Id: I0b9601c160dd4f2421a03ce6e3e7c55c6212f714
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8128
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Both devices can be configured with or without SWD multidrop.
nRF53 network core is examined on demand to avoid problems
when the core is forced off.
Change-Id: I08f88ff48ff7ac592e9214b89ca8e5e9428573a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8113
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Configure the TRACECONFIG.TRACEPORTSPEED register depending on the
trace clock speed. Also catch invalid trace clock speeds.
Change-Id: I1ece1cc59da539732d2d71f296fd55799c195387
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8256
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Use 'error' instead of 'echo' for error messages. Otherwise, capturing
is always started, for example with an unsupported device.
While at it, make the error messages more consistent and clear.
Change-Id: I83c9abfb4514e6b638c4be14651e67f768af8bad
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8255
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: <post@frankplowman.com>
Add some helpers for booting ZynqMPs over JTAG. Normally, the CSU ROM
will load boot.bin from the boot medium. However, when booting from JTAG
we have to do this ourselves. There are generally two parts to this.
First, we need to load the PMU firmware. Xilinx's tools do this by
attaching to the PMU (a Microblaze CPU) over JTAG. However, the TAP is
undocumented and we don't have any microblaze support in-tree. So
instead we do it the same way FSBL does it:
- We ask the PMU to halt
- We load the firmware into the PMU RAM
- We ask the PMU to resume
The second thing we need to do is start one of the APU cores. When an
APU is released from reset, it starts executing at the value of its
RVBARADDR. While we could load the APU firmware over the AXI target,
it is faster to load it over the APU target. To do this, we put the APU
into an infinite loop before halting it. As an aside, I chose to use the
"APU" terminology as opposed to "core" to make it clear that these
commands operate on the A53 cores and not the R5F cores.
Typical usage of these commands could look something like
targets uscale.axi
boot_pmu /path/to/pmu-firmware.bin
boot_apu /path/to/u-boot-spl.bin
But of course there is always the option to call lower-level commands
individually if your boot process is more unusual.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I816940c2022ccca0fabb489aa75d682edd0f6138
Reviewed-on: https://review.openocd.org/c/openocd/+/8133
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
After 'reset run' or 'reset halt' the loaded application
is expected to manipulate RAMON register to workaround
the known silicon errata.
Moreover, writing to RAMON register from 'reset-end' event
after 'reset run' may collide with application intentions.
Use the workaround in 'reset-init' event only to ensure
correct function of target algorithms.
Change-Id: I7d2d92e6805a05a83676edb46b3163ef39b9a7e4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8104
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the newer driver name 'nrf5' instead.
While on it set the unused parameters of flash bank
creation to zero.
While on it remove 2 empty comments.
Change-Id: I9cf0eadc5b696e6c8b7e6aec0ea3345967523e87
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8103
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
- Example for configuring multiple non-SMP
Xtensa cores e.g. for heterogeneous debug
- JTAG only at this time; DAP out of scope
- Dual-Xtensa Palladium example via VDebug
- Update Xtensa core config examples
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I6d2b3d13fa8075416dcd383cf256a3e8582ee1c1
Reviewed-on: https://review.openocd.org/c/openocd/+/8078
Tested-by: jenkins
Reviewed-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This change implements the support for the ARM Debug Interface v6.
The DAP-level interface properly selects the DP Banks and AP address.
Sample ARM configuration DAP and JTAG scripts have been updated.
Change-Id: I7df87ef764bca587697c778810443649a7f46c2b
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8067
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
S32K General-Purpose Microcontrollers
Scalable, low-power Arm® Cortex®-M series-based microcontrollers AEC-Q100
qualified with advanced safety and security and software support for
industrial and automotive ASIL B/D applications in body, zone control,
and electrification.
Change-Id: I4143258535437c18b81802436267bfd561de9d31
Signed-off-by: David Vidrie Leon <davidvidrie@geotab.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8012
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Tested with APM32F103CBT6 using JTAG and SWD transport. All flash
operations, including sector and device protection, work as expected.
Change-Id: Ibefe1a65d710aea87b86ab7ff8a4153512a0ea4f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8017
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested with APM32407RGT6 using JTAG and SWD transport. All flash
operations, including sector and device protection, work as expected.
Revision identifier (0x0009) is not updated due to missing documentation.
Change-Id: I33f4630fd00096656369ecc923aea2dcad77c7d3
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8016
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested with APM32F030C8T using SWD transport. All flash operations,
including sector and device protection, work as expected.
Revision identifier (0x0011) is not updated due to missing documentation.
Introduce a new directory structure that contains the manufacturer for
the sake of clarity.
Change-Id: I679387943b09fef640f8f8b6904e542f4e4b29aa
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8015
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
