The _targets has to be global as it is accessed at the end of this file.
This is already the case for setup_a5x {}, assure it is the same way for
setup_crx{} . Without this change, the _targets at the end of this file
is empty in case the Cortex-R is the boot core, fix this.
Change-Id: I4979e3125ec7d93bbd56eee0096ae1d9c5f6a565
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8470
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
virtex2 refresh replaced virtex2 program, but the even older programming
commands like xc6s_program still suggest the old, now-removed program
command. This changes the warnings to suggest the command that is still
there, and also adds some indication that you will need to use the .pld
name instead of the .tap name.
Change-Id: I292da62a95a9b414c69cdb1bba8a28dfd16a7336
Signed-off-by: Adam Novak <interfect@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8468
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Daniel Anselmi <danselmi@gmx.ch>
Adds initial support for the BL702 series of chips, BL702, BL704 and BL706.
No flash bank support yet.
File name bl702.tcl was chosen over bl70x.tcl, because Bouffalo Lab
uses bl702 to mark the whole series in many of their tools.
The ndmreset bit in the RISC-V Debug Module isn't implemented correctly,
so it doesn't trigger a system reset as it should.
To solve this problem, the software reset is implemented
in the reset-assert-pre hook, which uses best reset method I could find.
What is not reset is the GLB core, which handles GPIOs, pinmux, etc.
The reset mechanism has been extensively tested, and works correctly
for both "reset run" and "reset halt", which the latter
halts very early in the BootROM.
Change-Id: I5ced6eb3902d1b9d9c1bba56f817ec5dc3493cb0
Signed-off-by: Marek Kraus <gamelaster@outlook.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8407
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Direct memory driver swd native configuration for am62a7, am62p and
J722S SoCs. All three share common memory map for the debug address
map, so there is a strong reuse. However, introduce board file
specific to the board to allow users to directly get started.
Change-Id: I5609925a2e9918fd4c91d9fd40fbee98de27fdbc
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8283
Tested-by: jenkins
Reviewed-by: Vaishnav M A <vaishnav@beagleboard.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The flag '-coreid' is used by the command 'target create' to
specify the debug controller of the target, either in case of a
single debug controller for multiple CPU (e.g. RISC-V harts) or
in case of multiple CPU on a DAP access port (e.g. Cortex-A SMP
cluster).
It is also currently used to specify the CPU ID in a SMP cluster,
but this is going to be reworked.
This flag has no effects on Cortex-M; ARM specifies that only one
CPU Cortex-M can occupy the DAP access port by using hardcoded
addresses.
The flash driver 'psoc6' uses the flag '-coreid' to detect if the
current target is the Cortex-M0 on AP#1 or the Cortex-M4 on AP#2
in the SoC.
There are other ways to run such detection, without using such
unrelated '-coreid' flag, e.g. using the AP number or the arch
type of the target.
Use the arch type to detect Cortex-M0 (ARM_ARCH_V6M) vs Cortex-M4
(ARM_ARCH_V7M).
Drop the flags '-coreid' from the psoc6 configuration file.
Change-Id: I0b9601c160dd4f2421a03ce6e3e7c55c6212f714
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8128
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make sure raspberrypi-native.cfg cannot be used on RPi5.
Add raspberrypi5-gpiod.cfg which uses linuxgpiod adapter driver.
Issue a warning if PCIe is in power save mode.
While on it, re-format warnings issued from Tcl to look similar
to LOG_WARNING() output.
Change-Id: If19b0350bd5fff83d9a0c65999e33b161fb6957a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8333
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Remove list of id codes for all families.
Maintain a list with id, bscan-length and check position
in the tcl config files for each family.
The Intel FPGA Driver option 'family' is not otional anymore.
Change-Id: I9a40a041069e84f6b4728f2cd715756a36759c89
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/8083
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Both devices can be configured with or without SWD multidrop.
nRF53 network core is examined on demand to avoid problems
when the core is forced off.
Change-Id: I08f88ff48ff7ac592e9214b89ca8e5e9428573a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8113
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
