Purge all legacy interface configurations so there's no more confusion
over which one to use.
Also remove doc/INSTALL.txt which mentions ft2232 but otherwise just
duplicates what INSTALL says.
Change-Id: Ic94f808f123d4917e600b79309f1272c78a7bb11
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3236
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Do not configure internal libjaylink if libusb-1.0 is not available or
if J-Link driver is disabled (--disable-jlink).
Change-Id: I021bca91dbbc33888a997c664f7836225306c3ef
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3528
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Since OpenOCD doesn't fit most common definitions of the word "daemon",
using it in the documentation is confusing.
Reported by IRC user ohsix.
Change-Id: I688d722771b084b17c2a7af8e83fd64bab6141b8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3634
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Since merge of #3149 OpenOCD start with an unresponsive SAMD or SAM4L
resulted in segfaults. First was in cortex_m_assert_reset
(fixed by #3552), second was in samd_handle_reset_deassert()
/sam4l_handle_reset_deassert().
The change replaces mem_ap_write_u32/8 by target_write_u32/8.
It also takes better care about examining and polling target before
debug control registers are set. It prevents lockup when 'reset halt'
is issued on unresponsive cpu.
Change-Id: I2516489f4771aebfc1118d174f527497b8a201ad
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3603
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The MDR parts have two kinds of memory: main (regular memory-mapped
memory for code and data) and "info" (not memory-mapped). When OpenOCD
is requested to erase the info memory block, it should do just that,
instead of erasing everything including main memory.
Change-Id: I498142ca50d4a7b669b7776180b0dbcea63a5328
Reported-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3853
Tested-by: jenkins
Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
On multi-core systems, with some cores in power-down state, examination
will fail for these cores. Make sure assert- and deassert_reset functions
don't crash due to uninitialized variables.
Change-Id: I472f8d19af2cd3c770c05f3e57a31b35a863b687
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3552
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add semihosting support for ARMv7-A based processors.
Tested with custom Vybrid VF610 based board
and Pandaboard ES (Rev. B1) board (Cortex-A9).
Change-Id: I6b896a61c1c6a1c5dcf89de834486f82dd6c80a2
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Tsung-Han Lin <tsunghan.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/2908
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Nand write command :
nand_fileio_cleanup() always returns ERROR_OK. Due to this,
handle_nand_write_command() retuns ERROR_OK in the case
of nand failure. ERROR_FAIL should be returned.
Flash erase_sector command :
handle_flash_erase_command() always returns ERROR_OK even if
the erase functionality of actual driver implementation fails.
retval value should be returned.
Flash write_bank command :
handle_flash_write_bank_command() returns ERROR_OK even if
fileio_open() and fileio_read fails. ERROR_FAIL should be
returned.
Load_image command :
handle_load_image_command() retuns ERROR_OK even if image_open()
fails. ERROR_FAIL should be returned.
When the buffer is null, breaking the loop without setting
retval = ERROR_FAIL would cause load_image to return ERROR_OK.
Change-Id: Ice32f6036971ab5e8e4dd65edf54b394b001c80c
Signed-off-by: HarishKumar <harishpresent@gmail.com>
Reviewed-on: http://openocd.zylin.com/2431
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
With -Og gcc doesn't perform as many optimizations, and as a result
warns about some code that it wouldn't otherwise warn about.
These fixes all assign values to otherwise uninitialized variables.
Change-Id: I9a6ea5eadd73673891ecfec568b8b00d78b596a5
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/3779
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
To speed up downloads, OpenOCD sends gdb OK when a write is received,
even before the write has actually occurred. The failure is then
returned for the next write. That leads to the following confusing
behavior:
```
(gdb) p/x *((int*)0xdeadbeef)=8675309
$2 = 0x845fed
(gdb) p/x *((int*)0x80000000)=6874742
Cannot access memory at address 0x80000000
```
While it's actually the first write that failed.
This change hacks around this problem by not sending OK for small writes
(len<8) until the write has actually occurred. This does not impact
download speed, since during downloads (almost) all writes will have
much larger length.
Change-Id: I1f8b9bb19b0707487f840df6871e372e4ba228dd
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/3803
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Known big flash parts such as LPC11u68/e68 have a non-uniform memory
organisation, the first 24 sectors are 4k, the rest are 32k.
Change-Id: Icf515152dfc54ec0ca187561d2d63088b9640f14
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3802
Tested-by: jenkins
Reviewed-by: akaWolf
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
struct flash_driver has a default_padded_value field that is similar,
but it can be changed by the user for the specific purpose of padding.
Add a new erased_value field and initialize it for all targets,
particularly stm32lx, xmc4xxx and virtual.
Use this value in core.c:default_flash_mem_blank_check(), the slow path.
Extend the target API to pass erased_value down to target code.
Adding an argument ensures that we catch all callers.
This allows us to merge xmc4xxx.c:xmc4xxx_blank_check_memory() into
armv7m:armv7m_blank_check_memory().
It further allows us to use default_flash_blank_check() in place of
xmc4xxx.c:xmc4xxx_flash_blank_check(), adding a potential slow path
fallback, as well as stm32lx:stm32lx_erase_check(), adding the potential
armv7m fast path with fallback to default_flash_mem_blank_check().
Fix a mips32 code comment while at it (zeroed -> erased).
The armv4_5 and mips32 target implementations will now error out if an
erase value other than 0xff is used, causing default_flash_blank_check()
to fall back to the default_flank_mem_blank_check() slow path.
Change-Id: I39323fbbc4b71c256cd567e439896d0245d4745f
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3497
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The current implementation is not suitable for user provided data
because it does not detect invalid inputs in many cases. For example,
the string "aa0xbb" is successfully converted to the 3 bytes: 0xaa,
0x00 and 0xbb. An other example is "aabi" which is successfully
converted to the 2 bytes: 0xaa and 0x0b. Both are obviously incorrect.
Make unhexify() robust on invalid data and use more appropriate data
types for its parameters. Also, add a small documentation for the
function.
Change-Id: Idb799beb86fc608b066c8a76365021ed44c7f890
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3792
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Clean up some type casts and misuses of format specifiers in preparation
for target address type changes.
Change-Id: Idf08286f41bca636e35a09e8ddc1d71af3d6e151
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3717
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Insert a space before parenthesis in logs that we will need to touch
for 64-bit target addresses.
While at it, do a couple more surrounding whitespace fixes.
Change-Id: I1080c0470aab51cf7bd56e67e934344d0bf4c5c1
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3716
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
A space after the format specifier was missing.
Change-Id: Ib67eb0fb0d6e05d765206d30d5e4a74cb41bb47b
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3715
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
working_area_phys_spec clearly refers to the physical, not virtual address.
Change-Id: I639ea00bb5d05e845b8a56815a571375849f1225
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3714
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This makes it possible to run OpenOCD as unprivileged user on FreeBSD.
Change-Id: If1182d09ad2d51f370ae7e6da02f19c7a21c66c9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3800
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Even when TRST and SRST are not present in reset_config we still should
set them appropriately (to 1) as we can't tristate them anyhow.
Change-Id: Iec5bcf09340136f5e6ccfb05fa2697c53fa6609f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3798
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
