The "parport_port" commands generally don't *require* a port_number;
they're of the "apply any parameter, then print result" variety. Update
the User's Guide accordingly.
Some of those commands are intended to be write-once: parport_port,
and parport_cable. Say so.
Use proper EBNF for the parport_write_on_exit parameter.
Parport address 0xc8b8 is evidently mutant. Say so in the "parport.cfg"
file, to avoid breaking anyone with that mutant config. But update the
User's Guide to include a sane example for the LP2 port.
Finally document the "presto_serial" command.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
add reset-init script to allow ram execution from reset, this is required for ejtag fastdata access.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The relevant cable config is already in OpenOCD, but not a config for
the JTAG adapter. I have tested with FlashLINK on ARM926.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most of this patch updates documentation and comments for various
Luminary boards, supporting two bug fixes by helping to make sense
of the current mess:
- Recent rev C lm3s811 eval boards didn't work. They must use
the ICDI layout, which sets up some signals that the older
boards didn't need. This is actually safe and appropriate
for *all* recent boards ... so just make "luminary.cfg" use
the ICDI layout.
- "luminary-lm3s811.cfg", was previously unusable! No VID/PID;
and the wrong vendor string. Make it work, but reserve it
for older boards where the ICDI layout is wrong.
- Default the LM3748 eval board to "luminary.cfg", like the
other boards. If someone uses an external JTAG adapter, all
boards will use the same workaround (override that default).
The difference between the two FT2232 layouts is that eventually
the EVB layout will fail cleanly when asked to enable SWO trace,
but the ICDI layout will as cleanly be able to enable it. Folk
using "luminary.cfg" with Rev B boards won't see anything going
wrong until SWO support is (someday) added.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This config is only lightly tested, and doesn't work well yet;
but it's a start.
* Notably missing is PLL configuration, since each DaVinci
does that just a bit differently; and thus DDR2 setup.
* The SRST workaround needed for the goof in the CPLD's VHDL
depends on at least the not-yet-merged patch letting ARM9
(and ARM7) chips perform resets that don't use SRST.
So this isn't yet suitable for debugging U-Boot.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The 10-pin JTAG layout used with these adapters is used by
a variety of platforms including AVR.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This updates the board configuration for the SAM9-L9260 board with the
configuration for the on-board NAND and dataflash. Included are commands
for configuring the AT91SAM9 NAND flash driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove more remnants of the old "jtag_device" syntax.
Don't [format "%s.cpu" $_CHIPNAME] ... it's needless complexity.
Remove various non-supported "-variant" target options; they're not
needed often at all.
Flag some of the board files as needing to have and use target files
for the TAP and target declarations.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
That syntax has been obsolete forever and is now gone; remove a few
remaining references. Shows how seldom this stuff gets used.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Common target.cfg file for LM3S CPU family
[dbrownell@users.sourceforge.net: rename, generalize more]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Behave like OMAP3530: force global software reset. Given the
patch to teach ARM11 how to use these events, and use VCR to
catch the reset vector, this works better than either the
current reset logic or than using SRST.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
