Driver for DesignWare SPI controller, found on many SoCs (see compatible
list in Linux device tree bindings
Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml). This
implementation only supports MIPS as it was the only one available for the
tests, however, adding support for other architectures should require only
few adjustments. Driver relies on flash/nor/spi.h to find Flash chip info.
Driver internal functions support 24bit addressing mode, but due to
limitations of flash/nor/spi.h, it is not used. The reported writing speed
is about 60kb/s.
Lint, sanitizer and valgrind reported warnings were not related to the
driver.
Change-Id: Id3df5626ab88055f034f74f274823051dedefeb1
Signed-off-by: Sergey Matsievskiy <matsievskiysv@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8400
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To alleviate the need to bitbang SWD, I've written a SWD SPI
implementation. This code is inspired by the work of luppy@appkaki.com
as shown at github.com/lupyuen/openocd-spi but with the desire to be
more generic. This implementation makes use of the more common 4 wire
SPI port using full duplex transfers to be able to capture the SWD ACK
bits when a SWD TX operation is in progress.
TEST:
Connects successfully with the following combinations:
Hosts:
Raspberry Pi 4B
Unnamed Qualcomm SoC with QUPv3 based SPI port
Targets:
Raspberry Pi 2040
Nordic nRF52840
NXP RT500
Change-Id: Ic2f38a1806085d527e6f999a3d15aea6f32d1019
Signed-off-by: Richard Pasek <rpasek@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8645
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
The log messages are very inconsistent across the code base. Add a
guideline for log messages to help improve consistency. The guideline is
based on the most commonly used style in the current code base.
Change-Id: I076d68abe588dd04b59580379e97b82d537def23
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8576
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The STLink API that supports dap-direct is available from STLink
firmware v2j24, published in early 2015.
We can reasonably expect that any old STLink still in use today
has got at least one firmware update during the last 10 years.
Most of the board files in upstream OpenOCD still use the STLink
in HLA mode. This limits the test coverage of the dap-direct code,
which was introduced in OpenOCD v0.11.0.
- Rename interface/stlink.cfg as interface/stlink-hla.cfg to still
provide support for HLA, adding a deprecated message.
- Rename interface/stlink-dap.cfg as interface/stlink.cfg to make
dap-direct the default trasport.
- Add a redirect file interface/stlink-dap.cfg for users that have
out-of-tree custom board files.
- Update all the board files to the new setup.
- Remove STLink HLA mentions from the documentation, while adding
a reference to interface/stlink-hla.cfg
Checkpatch-ignore: LONG_LINE
Change-Id: I99366bb03cd3b83f8f408514e657f30e59813063
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8523
Tested-by: jenkins
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
Use a command group 'telnet' with subcommands instead of individual
commands with 'telnet_' prefix. Even though there is only one subcommand
at the moment, make this change to ensure consistency with other commands.
The old command is still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I5e88632fa0d0ce5a8129e9fcf5ae743fc5b093cb
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8378
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
stm32l4x option_write works like stm32h7x option_write, i.e. expects the
value to write after reg_offset and optionally reg_mask after the value.
Change-Id: I57fb4fb1dbf7f43fe063b48f4db2dd5f2ef0ade0
Signed-off-by: Ondřej Hošek <ondra.hosek@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8464
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Do not echo the selected transport to avoid stray and confusing
messages in the output of OpenOCD. For example, the "swd" line here:
Open On-Chip Debugger 0.12.0+dev-00559-ge02f6c1b9-dirty
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
swd
Info : Listening on port 6666 for tcl connections
Info : Listening on port 4444 for telnet connections
While at it, fix some small documentation style issues.
Change-Id: Ie85426c441289bbaa35615dbb7b53f0b5c46cfc0
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8217
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Build returns a makeinfo warning:
openocd.texi:5201: warning: `.' or `,' must follow @xref, not f
Add a dummy ',' after '@xref{..}' to silent the warning.
Fixes: 44cfdef0a4 ("server/gdb: Restructure commands")
Change-Id: Ic0bff8fc9b54942ebb72762816686ea7c7881345
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8392
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Use a command group 'tcl' with subcommands instead of individual
commands with 'tcl_' prefix.
The old commands are still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I1efd8a0e2c1403833f8cb656510a54d5ab0b2740
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8344
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Use a command group 'gdb' with subcommands instead of individual
commands with 'gdb_' prefix.
The old commands are still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I037dc58554e589d5710cf46924e0a00f863aa300
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8336
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'hla' with subcommands instead of individual
commands with 'hla_' prefix.
The old commands are still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I612e3cc080d308735932aea0f11001428eadc570
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8335
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Remove the outdated option '--pipe' and bring the description of OpenOCD
up to date without focus on JTAG only.
Change-Id: If52e936a366dde21c1dd514bd3960d100b540e77
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8347
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add to the command 'target create' the description for the flags
'-dbgbase' and '-coreid'.
Report that '-coreid' is currently used for purposes other than
CPU detection/examination, and that such uses are going to be
re-considered.
Change-Id: I25c839e3653101234c5862ce9da77019a5bb3249
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8129
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Remove list of id codes for all families.
Maintain a list with id, bscan-length and check position
in the tcl config files for each family.
The Intel FPGA Driver option 'family' is not otional anymore.
Change-Id: I9a40a041069e84f6b4728f2cd715756a36759c89
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/8083
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Probes all flash and UICR areas.
Flash erase and write tested.
On nRF53 mass erase works on the application core flash bank only.
The Tcl script nrf53_recover can serve as the workaround on the
network core.
TODO: mass erase of the nRF53 network core flash.
Some ideas taken from [1] and [2].
Change-Id: I8e27a780f4d82bcabf029f79b87ac46cf6a531c7
Link: [1] 7404: flash: nor: add support for Nordic nRF9160 | https://review.openocd.org/c/openocd/+/7404
Link: [2] 8062: flash: nor: add support for Nordic nRF9160 | https://review.openocd.org/c/openocd/+/8062
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8112
Reviewed-by: Tomáš Beneš <tomas@dronetag.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
