Stick with the name "gdb_port" even if this command
can be used for other things(disable, named pipes,
anonymous stdin/out pipe). "port" is correct for
probably more than 90% of use cases, if not more.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This will allow switching to using named pipes.
Split this out as a seperate commit to make changes
easier to follow.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
depending on whether the connection is over a socket
or pipe, the read is done differently.
pipes can return -1 when writing 0 bytes, make 0 byte
writes a successful no-op. 0 byte writes falls out
naturally of tcl server code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
pipes have different fd's for in/out. This makes the
code more orthogonal and prepares for adding pipes.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
there was special support to support pressing 'x' to quit
openocd. ctrl-c is sufficient. The main server loop is already
complicated enough.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
by using ctrl-z instead of line end, multi-line tcl scripts
can be handled.
Testing: send ctrl-z a couple of times to make telnet enter the
mode where it sends ctrl-z unencoded.
Programs that talk to the tcl_server can send ctrl-z to
indicate end of tcl-let to be executed without having
to worry about telnet protocols.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb server incorrectly reports the memory map if we have
multiple targets with multiple flash banks.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This warning was only reproducable with
Cygwin.
Cygwin now builds without warnings for the basic
case.
Signed-off-by: Oyvind Harboe <oyvind.harboe@zylin.com>
if step/continue fails, then the error should be
reported to the calling fn.
The calling fn decides if the connection has to be
aborted or if packet processing can continue.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
GDB and OpenOCD has two different error number
spaces and no mapping exists between them.
If a specific error number is to be reported
to GDB then this has to be done at the calling
site, rather than as a generic routine that
tries to map "retval" to GDB error number speak.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb_memory_map cmd for example fell through and returned
ERROR_COMMAND_SYNTAX_ERROR on success - behaviour is now as expected.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
reproducable when "./configure --enable-maintainer-mode CFLAGS=-D_DEBUG_GDB_IO_"
Signed-off-by: Jun Ma <sync.jma@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
c->sin.sin_port does not contain a valid port number so just use
service->port as this is always correct.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This stops GDB from launching with an empty memory map,
making gdb load w/flashing fail for no obvious reason.
The error message points in the direction of the gdb-attach
event that can be set up to issue a halt or "reset init"
which will put GDB in a well defined stated upon attach
and thus have a robust flash autoprobe.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
No segmentationfault when sending commands to tcl-server.
modified: src/server/server.c
modified: src/server/tcl_server.c
modified: src/server/tcl_server.h
by ack'ing memory writes immediately and reporting either
at next memory write or stepi/continue time. GDB will then
send off a new packet that is ready by the time the previous
packet has been written to target memory.
On faster adapters this can be as much as 10% improvement.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Sometimes we saw two strange blank spaces at the beginning
of the telnet lines.
progress
ogress
>
This patch fixes this problem:
progress
progress
>
The code changes are *reasonably* clean, but perhaps it could be
made a bit more elegant, but I didn't want to change things after
I finished diagnosis/testing & submitting the patch.
The problem was that logging can send the text and the newline
separately in two different requests and the telnet code would
incorrectly remove the prompt from the end of a line.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
