Use a command group 'kitprog' with subcommands instead of individual
commands with 'kitprog_' prefix.
The old command is still available to ensure backwards compatibility,
but is marked as deprecated.
Change-Id: I7f0d447939819ffc488a3d7a8de672b58887127f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7967
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'cmsis-dap' with subcommands instead of individual
commands with 'cmsis_dap_' prefix.
The old commands are still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I75facb7572a86354c2ce6144aa7fadf3b5a6db4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7963
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds the "all" option to the rwp command.
It removes all watchpoints, much like rbp all removes
all breakpoints.
Change-Id: Id58dd103085e558f17afa4a287888cf085566ca9
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7907
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Previously, if you ran a tcl command in capture like so:
"capture { reg 0x1000 hw }"
Such command did overwrite the tcl result if LOG_LVL_INFO or
lower was logged during it.
This patch changes it by prepending the log to the tcl result instead.
As the tcl results should not be lost during capture.
Change-Id: I37381b45e15c931ba2844d65c9d38f6ed2f6e4fd
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7902
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
add refresh command for lattice devices
rename gowin reprogram to refresh
rename virtex2 program to refresh
Change-Id: I9da83a614b96da3e947ac4608b0a291b1d126914
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7839
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Jtagspi is using a proxy bitstream to "connect" JTAG to the
SPI pins. This is not possible with all FPGA vendors/families.
In this cases a dedicated procedure is needed to establish such
a connection.
This patch adds a jtagspi-mode for these cases. It also adds the
needed interfaces to jtagspi and the pld-driver so the driver
can select the mode and provide the necessary procedures.
For the cases where a proxy bitstream is needed, the pld driver
will select the mode and provide instruction code needed in this
case.
Change-Id: I9563f26739589157b39a3664a73d91152cd13f77
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7822
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Enumerator's case were not specified in the coding style.
Add enumerators together with macros for upper-case preference.
While there, add the word CamelCase beside the less common, but
already used, MixedCaps. This could help linking this chapter to
the output of checkpatch script.
Change-Id: I6d4af06cc6f4bc46f525e99e9a74ecc167606c49
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7875
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
add new i2c bit-banging feature, we can now connect in JTAG with the SoC
target and in i2c with the main board components at the same time.
Change-Id: I8e4516fe1ad5238e0373444f1c3c9bc0814d0f52
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7796
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This emulation mode supports software translation of an AP request
into an address mapped transaction that does not rely on physical AP
hardware. This is necessary in some hardware such as K3 SoCs since the
hardware architecture anticipates a potential race condition between
AP doing direct memory access generating transactions back to system
bus and firewalls that data path out.
This emulation mode allows direct memory driver to emulate CoreSight
Access Port (AP) and reuse the SoC configuration meant for JTAG
debuggers.
Since the address ranges are flat in nature, the requisite memory base
and size will need to be provided a-priori to the driver for mapping.
The other design alternative would be to map requested memory map for
every register operation, but, that would defeat our intent of getting
max debug performance.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Peck <jpeck@ti.com>
Change-Id: I2d3c5f7833f1973e90b4f6b247827f62fc2905d0
Reviewed-on: https://review.openocd.org/c/openocd/+/7089
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Direct memory driver support for CoreSight Access Port(AP).
Even though we emulate SWD (serial wire debug), we aren't actually
using swd. Instead, we are using a direct memory access to get to the
register set. This is similar in approach to other fast access native
drivers such as am335xgpio drivers.
Example operation on Texas Instrument's AM62x K3 SoC:
+-----------+
| OpenOCD | SoC mem map
| on |--------------+
| Cortex-A53| |
+-----------+ |
|
+-----------+ +-----v-----+
|Cortex-M4F |<───────| |
+-----------+ | |
| DebugSS |
+-----------+ | |
|Cortex-M4F |<───────| |
+-----------+ +-----------+
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Peck <jpeck@ti.com>
Change-Id: I8470cb15348863dd844b2c0e3f63a9063cb032c6
Reviewed-on: https://review.openocd.org/c/openocd/+/7088
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter.
The driver is based on the openULINK project.
This driver communicate with ANGIE's firmware in order to establish
JTAG protocol to debug the target chip.
Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the
FX2 microcontroller, the driver adds two functions, one to download
the firmware (embedded C) to the FX2, and the second to program
the FPGA with its bitstream.
Add ANGIE's configuration file to tcl/interface/
Add the device VID/PID to 60-openocd.rules file.
Add ANGIE to OpenOCD's documentation
Change-Id: Id17111c74073da01450d43d466e11b0cc086691f
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7702
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This is ANGIE's firmware and bitstream code.
The 'Embeded C' code is based on the openULINK project.
The hdl bitstream source code is for the spartan-6 FPGA included in
ANGIE.
Since ANGIE has a different microcontroller (EZ-USB FX2) than openULINK
(EZ-USB AN2131), the registers file (reg_ezusb.h) has been changed
completely, so are the descriptors, interruptions and the endpoints
configuration.
Change-Id: I70590c7c58bac6f1939c5ffba57e87d86850664d
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7701
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
To start a ipdbg server one needs to know the tap and the
instruction code to reach the IPDBG-Hub. This instruction is
vendor/family specific. Knowledge which can be provided by the
pld driver.
Change-Id: I13eeb9fee895d65cd48544da4704fcc9b528b869
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7369
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds support for the NXP QN908x family of Bluetooth
microcontrollers, such as the QN9080. This chip features a Cortex-M4F
with 512 KiB of flash on all the available versions, although the
documentation suggests that there might be 256 kB versions as well.
The initial support allows to read, erase and write the whole user flash
area. Three new sub-commands under the new "qn908x" command are added
in this patch as well: disable_wdog to disabled the watchdog,
mass_erase to perform a mass erase and allow_brick to allow programming
images that disable the SWD interface.
Disabling the watchdog is required after a "reset halt" in order to run
the CRC algorithm from RAM when verifying the chip. However, this is not
done automatically on probing or other initialization since disabling
the watchdog might interfere with debugging real applications.
The "mass_erase" command allows to erase the whole flash without
probing it, since in some scenarios the chip can be locked such that no
flash or ram can be accessed from the SWD interface, allowing only to
run a mass_erase to be able to flash the program.
The flashing process allows to compute a checksum, similar to the
lpc2000 driver "calc_checksum" but done over a different region of the
memory. This checksum is required to be present for the QN908x
bootloader ROM to boot, and otherwise is useless. As with the lpc2000
design, verification when using "calc_checksum" is expected to fail if
the checksum was not valid in the image being verified.
This was manually tested on a QN9080, including the scan-view,
AddressSanitizer/UBSan and test coverage configurations.
Change-Id: Ibd6d8f3608654294795085fcaaffb448b77cc58b
Co-developed-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: iosabi <iosabi@protonmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5584
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
