This patch adds the initial dual flash bank support for devices such
as the stm32xl family.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
this allows configuration scripts to export a init_targets proc
rather than setting up the target directly.
This allows for new conventions in how to set up target vs. board
script and how to transfer default settings between board and
target scripts.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
the error values is not part of the interface to the user,
so they should never be printed in LOG_INFO or LOG_USER.
Printing them in LOG_DEBUG() rarely makes much sense but
is OK.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Only Tcl comments are now supported. For classic style
commands comments were supported at the end of the line.
Move in the direction of letting the script language
decide syntax, rather than have special rules for some
commands.
Before this patch goes in, the scripts should be updated
to use ;# instead of # for end of line comments.
> mdw 0 1 2
mdw ['phys'] address [count]
zy1000.cpu mdw address [count]
Command handler execution failed
in procedure 'mdw'
> mdw 0 1 #2
mdw ['phys'] address [count]
zy1000.cpu mdw address [count]
Command handler execution failed
in procedure 'mdw'
> mdw 0 1 ;#2
0x00000000: ffffffff
> mdw 0 1
0x00000000: ffffffff
> mdw 0
0x00000000: ffffffff
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
the unprotect fn in stm32 needs to unprotect more sectors
than was requested aligned to some boundary.
Print warning when this happens.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
some chips unprotect more than the range asked for. The
protect fn, must unprotect/protect minimally the range given.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Some flash's do not support buffer writes, so we now check
they are supported before trying to use them.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The existing code used incorrect timeout values for the various cfi
operations. We now calculate the timeouts and convert to
msecs if necessary.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
If the JTAG speed has not been set, then it has no defined
value, add code to propagate the error.
No change to actual behavior as no new failure paths have
been introduced. This is a no-op patch to make subsequent patches
smaller.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* added support for targeting particular tap
* improved file reading
* improved command line parsing
* added progress meter
* more readable time measurement output
Hi everyone,
Since a call went out for patches... been sitting on this for months. For some
reason, the xscale trace buffer is automatically disabled as soon as a break
occurs and the trace data is collected. This patch was a result of the
frustration of always re-enabling it, or else hitting a breakpoint and checking
the trace data, only to discover that I forgot to re-enable it before resuming.
Don't see why it should work this way. There is no run-time penalty, AFAIK.
Along the way, I also cleaned up a little by removing the ugly practice of
recording wrap mode by setting the fill count variable to "-1", replacing it
with an enum that records the trace mode.
I've been using this for months. Comments, criticisms gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Currently the cmd 'cortex_m3 reset_config' will overide the default
target's 'reset_config'.
Chnage the behaviour to use the target 'reset_config' if configured and
fallback if not.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
it's a lie that is somewhere in the vicinity of the
truth. Certainly 64MHz confuses gprof and produces
zero output and no error messages.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
