reset_config is now supported by stlink, remove from the config as this
is a per board option.
Change-Id: I85208d2154502b8d3a098afe1d9a28d75820a7c0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/582
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
* Added support to the FT2232 driver for the FT2232H-based
Digilent HS1 adapter.
Change-Id: Iab6cc15f299badaf115615b5d4d785ecb2273c27
Signed-off-by: Stephane Bonnet <bonnetst@hds.utc.fr>
Reviewed-on: http://openocd.zylin.com/558
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This driver provides support for the P&E Micro OSBDM adapter (sometimes
named as OSJTAG), mounted on the Freescale TWRK60N512 bord. Thus, it
provides a quick start when working with this board. The driver doesn't
use BDM commands, but work with OSBDM adapter using only JTAG commands.
Change-Id: Ibc3779538e666e07651d3136431e5d44344f3b07
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-on: http://openocd.zylin.com/492
Tested-by: jenkins
Reviewed-by: Tomas Frydrych <tf+openocd@r-finger.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This only effects the older Stellaris LM3S811 kits (rev B and below).
Change-Id: Ie068cce7748fede9e7113ea63a69c96222c809fa
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/401
Tested-by: jenkins
This is a successor to the Flyswatter cable and is very close to the original.
The new revision is based on FT2232H.
Change-Id: Icc6efcf0e4f9d8a10b65df8679b4973f6b375a9f
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: David Anders <danders@tincantools.com>
Reviewed-on: http://openocd.zylin.com/193
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Also, drop author name from interface/hilscher_* files, that info is in the
git log, and none of the other files contain author names either.
Change-Id: Idf0eb4279c4bff31d15c166619c0bf8b1c5bb877
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/138
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The BusBlaster from Dangerous Prototypes is based on the FTDI FT2232H IC.
It has a CPLD between the FT2232H and the JTAG header allowing it to
emulate various debugger types. It comes configured as a JTAGkey compatible
device.
Change-Id: Iab56907bf67ded87001e628d93012f1e16287d90
Signed-off-by: Richard Barlow <richard@richardbarlow.co.uk>
Reviewed-on: http://openocd.zylin.com/53
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The DLP Design DLP-USB1232H UART/SPI/JTAG module is based on an FTDI FT2232H
chip. Among other things, it can used as JTAG programmer if connected to
the JTAG target properly. I have successfully wired the module to an
Olimex STM32-H103 eval board and flashed a firmware onto that using OpenOCD.
The setup details and schematics are documented at:
http://randomprojects.org/wiki/DLP-USB1232H_and_OpenOCD_based_JTAG_adapter
Change-Id: I5eb9255a61eeece233009bee77d7dc3b5d1afb8b
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/20
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently the board/redbee-*.cfg files incorrectly include the
interface definition. Move the interfaces to interface/,
and create a single board/redbee.cfg that is common to both boards.
Intended usage is now:
openocd -f interface/redbee-econotag.cfg -f board/redbee.cfg
End of line comments fixed with ';' before '#'.
Added few additional 'space' to keep indentation in
multi-line comments.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Clarify that ICDI is the generic logic, but this config is
for the JTAG-only (no-SWD) mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
