Added interface config file for the FTDI FT232H based UM232H module.
This should work with UM232H-B too, an even cheaper module, but
that has not been tested.
Change-Id: Ifc312d6741da0b7862fe07d854023190d7afe251
Signed-off-by: Ragnar Sundblad <raggesu@gmail.com>
Reviewed-on: http://openocd.zylin.com/3031
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Derived from tcl/interface/digilent-hs1.cfg.
JTAG-HS3 has an open drain buffer on pin 14 for SRST to work with
PS_SRST_B on Xilinx Zynq SoC.
Change-Id: I1e9e72d0511528a61207e318aff937ae9fad5bf9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2728
Tested-by: jenkins
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Pipistrello is a low cost FPGA board with a Xilinx
Spartan6 LX45, a SPI flash and onboard FTDI JTAG.
This board is a good example use case for the jtagspi
flash driver talking through a proxy bitstream.
Change-Id: I04a80610ff825c36ebcb67b879507028eed141ad
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2846
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The signal names are changed for consistency with TI's docs and
sources.
Change-Id: Ic5c5314daa20f6f610be8a848399f951d47aa137
Signed-off-by: Matthijs van Duin <matthijs@rinnic-vaude.nl>
Reviewed-on: http://openocd.zylin.com/2231
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
According to my inspection of an Olimex ARM-USB-OCD-H adapter ACBUS0
is connected directly to an SN74LVC2T45 buffer input B2, and the
corresponding output A2 is connected directly to the JTAG
connector. It seems the information in the Olimex flyer is incorrect
for the -H version and TRST can't be tri-stated, ACBUS2 is unused.
The older ARM-USB-OCD device has SN74AC244 for an output buffer and
ACBUS2 controls its !2OE, ACBUS0 connected to 2A1 (2Y1 is nTRST), in
accordance with the information flyer.
Change-Id: I22828b7b959b6f62c3f51367feb8fab9705641e5
Reported-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2286
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tim Sander <tim@krieglstein.org>
According to the research by Eldar, TINY-H adapter has nTRST connected
to ACBUS0 directly via a 100 Ohms series resistor. I think it's safe
to assume the older TINY adapter does the same.
See high-res photos at [1].
This patch should fix issues with JTAG for the case when nTRST is
actually connected but is missing from the config.
[1] https://wikidevi.com/wiki/Olimex_ARM-USB-TINY-H
Change-Id: Iaaee7be30536ebb502802d38b82cd9573408f854
Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2247
Tested-by: jenkins
Reviewed-by: demokmail <demokmail@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Use a special signal instead of a dedicated swd mask. Amend
jtag-lock-pick_tiny_2 config accordingly.
Change-Id: Ifb007a0b5434b590c52f936efd5f5458e913e2e4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2183
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The XDS100v2 is often embedded in a number of platforms using the
VID/PID of 0x0403/0x6010 and a generic FTDI device description. Add
this VID/PID combination and remove the description line.
Change-Id: I370e6199ac24f802426e9541e19ee38f18f1209a
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2016
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adapter is special and needs a reset sequence to be performed
before operation. Since there're no suitable hooks to do that, we have
no choice but to ask the user to manually add the necessary commands
to his or her config file.
Change-Id: I48fb4276e77529768266840221b68c3ae26801e1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1884
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
TUMPA Lite is a cheap FT232H-based breakout board, without any
buffering. It also lacks series resistors so for some targets
(especially when not using ridiculously short wires) one needs to add
about 47 Ohms in series on every high-speed line.
The SRST line is connected directly to the FT232H too.
Real-life tested (including SRST and TRST).
Change-Id: I5ed4f88d8d20384e9c52efe2ff0c290e2650d43e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1918
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
