When printing memory sizes standard ISO 80000-1 prefixes should be used.
Also a space should be added between any number and its unit according
to papers publication rules.
Change-Id: Id1d35e210766b55c201de4e80ac165d8d0414d0a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6416
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Fix Unused code Dead assignment at line 657
Fix Memory error Double free at line 2851
Fix Memory error Memory leak at line 2530
Fix error: 'a3' may be used uninitialized at line 758
Fix error: '%04x' directive writing between 4 and 8 bytes
into a region of size 5 at line 2471
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I0382a622bc7c4108a335fd741816577e79240397
Reviewed-on: https://review.openocd.org/c/openocd/+/7137
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Generic Xtensa LX support extends the original Espressif/Xtensa
patch-set to support arbitrary Xtensa configurations, as defined in
a core-specific .cfg file. Not yet fully-featured. Additional
functionality to be added:
- Xtensa NX support
- DAP/SWD support
- File-IO support
- Generic Xtensa multi-core support
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I08e7bf8fa57c25b5d0cb75a1aa7a2ac13a380c52
Reviewed-on: https://review.openocd.org/c/openocd/+/7055
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
linuxgpiod driver.
Adds support for drive mode and resistor pull options on all signals.
Change-Id: Ic90cb4f06db82435294228b6793330107a9f3606
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7048
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The /dev/mem file descriptor can be closed without invalidating the
mappings so close as soon as possible.
munmap() all memory, either on error or from quit.
Change-Id: I9466edd2f43791e64f2dce719957c67728f3ec06
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7047
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
am335xgpio driver. The AM335x has 4 GPIO 'chips' (chip number 0-3
inclusive), with each one providing 32 GPIOs (gpio_num 0-31 inclusive).
Change-Id: I7c63c0e4763657ea51790c43fc40d32b7c3580bb
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6984
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Most adapters define their own commands to obtain the GPIO number and
other GPIO configuration information such as chip number, output drive
type, active high/low.
Define a general command 'adapter gpio' as replacement for the
driver-specific ones.
Change-Id: I1ca9ca94f0c7df5713172e9f62ffb0ad64e9ee97
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6967
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The S_RESET_ST sticky bit is reset after DHCSR read.
It is set at power-on reset and keeps active until the debuger reads DHCSR.
Ignore S_RESET_ST at the very first read after OpenOCD start
and suppress possibly misleading message "external reset detected"
if we cannot guarantee the reset happened recently.
While on it add a TODO comment.
Change-Id: I15217c2ca6f69ac97aff8be86bce67cba94a42cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7109
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide a customizable hook for handling target-specific GDB queries
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I684a259ed29f3651cbce668101cff421e522f79e
Reviewed-on: https://review.openocd.org/c/openocd/+/7082
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command 'init' causes the execution of few lower level
commands, e.g. 'target init', and switches from command mode
COMMAND_CONFIG to COMMAND_EXEC, with an intermediate switch back
to mode COMMAND_CONFIG.
A timed target polling can occur during the execution of 'init'
and the target's status can trigger the execution of some events.
E.g. if a target has been left halted by a previous execution of
OpenOCD, the first poll will find the target halted, calling the
corresponding 'halted' event.
The event handler can use commands that can only be executed in
mode COMMAND_EXEC. If the poll happens while OpenOCD is in mode
COMMAND_CONFIG, the triggered handler will fail.
Prevent the target polling to operate during the execution of the
'init' command.
Change-Id: Ia435a5d2039be9b247e2336616dab53ed5d983ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7007
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The same flag 'jtag_poll' is currently used as local data for the
command 'poll' and to temporarily mask the target polling.
This can cause unexpected behavior if the command 'poll' is
executed while polling is temporarily masked.
Add a new flag 'jtag_poll_en' to hold the temporarily mask
condition and keep 'jtag_poll' for the 'poll' command only.
While there, change the initial assignment of 'jtag_poll' using
the proper boolean value.
Change-Id: I18dcf7c65b07aefadf046caaa2fcd2d74fa6fbae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7009
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
GDB remote serial protocol specifies breakpoint/watchpoint packet
responses can be an empty string to indicate the specified breakpoint
type is not supported. Add support for this response alongside existing
"OK", "E NN" replies.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: Iaf6280e4c936eb95a92bc80cc74d451ebb328dc3
Reviewed-on: https://review.openocd.org/c/openocd/+/7102
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After a certain RTOS has been configured there is no mechanism
to go back to no RTOS support. It may be useful for debugging
purposes. With the provided modification, the "none" option
of RTOS is provided as a valid option.
It has been tested in two different board (Cortex M4 and Cortex M33).
Documentation has also been updated.
Signed-off-by: Asier Llano <allano@hubbell.com>
Change-Id: I602210bff31ccadd41c41e9454c52b5fffa1671e
Reviewed-on: https://review.openocd.org/c/openocd/+/7092
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tcl commands 'arm reg', 'arm mcr/mrc' do not work on M-profile based devices.
Isolate them from 'arm core_state' and 'arm disassemble' and do not chain
them from armv7m_command_handlers.
Change-Id: I2c6befdf82575e95cf05ed158ab5e6faa1a182c3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7101
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Tcl command 'arm core_state' was exposed even on Cortex-M devices.
However it returned message "Unsupported Command" without error status
on such device.
Set the only possible arm->core_state ARM_STATE_THUMB in armv7m init.
Block setting core_state to arm on Cortex-M.
Change-Id: I9525553ac8863a6cf77bbacbcd57e354b6cfe1ca
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7100
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
If a Cortex-M MCU become unresponsive during a debug session and
re-examination fails to find MEM-AP, debug_ap pointer is set to NULL.
Eventual call of cortex_m_poll() dereferences debug_ap.
Check debug_ap validity at the begin of cortex_m_poll().
Change-Id: I9519f48760c91a48a9e5e8c34634d247098cb14a
Fixes: 35a503b08d (arm_adi_v5: add ap refcount and add get/put around ap use)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7108
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
AARCH64_COMMON_MAGIC was same as CORTEX_A_COMMON_MAGIC, probably copy pasta.
Define unique AARCH64_COMMON_MAGIC
Change-Id: Ie30e0028453a1fce5624ecad9bf73d5ac3791281
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6997
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Unify common_magic type to unsigned int
Move common_magic to be the first member of the struct
Add unsigned specifier to xxx_COMMON_MAGIC #defines
Change-Id: If961d33232698529514ba3720e04418baf6dc6fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6996
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
