Print "ssize_t" as "%ld" (+ cast to long) not as "%zu".
Official MinGW (gcc 3.4.5) doesn't understand "z" flag.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most of this patch updates documentation and comments for various
Luminary boards, supporting two bug fixes by helping to make sense
of the current mess:
- Recent rev C lm3s811 eval boards didn't work. They must use
the ICDI layout, which sets up some signals that the older
boards didn't need. This is actually safe and appropriate
for *all* recent boards ... so just make "luminary.cfg" use
the ICDI layout.
- "luminary-lm3s811.cfg", was previously unusable! No VID/PID;
and the wrong vendor string. Make it work, but reserve it
for older boards where the ICDI layout is wrong.
- Default the LM3748 eval board to "luminary.cfg", like the
other boards. If someone uses an external JTAG adapter, all
boards will use the same workaround (override that default).
The difference between the two FT2232 layouts is that eventually
the EVB layout will fail cleanly when asked to enable SWO trace,
but the ICDI layout will as cleanly be able to enable it. Folk
using "luminary.cfg" with Rev B boards won't see anything going
wrong until SWO support is (someday) added.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Otherwise the new alignment checking algorithm thinks that the
address is not aligned, because it is way beyond the last sector.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Resolve a regression when using newish automagic "write_image"
modes, by always padding to the end of affected sectors.
Also document some issues associated with those automagic options,
in the User's Guide and also some related code comments.
We might need similar padding at the *beginning* of some sectors,
but this is a minimalist fix for the problems which have currently
been reported (plus doc updates).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The 10-pin JTAG layout used with these adapters is used by
a variety of platforms including AVR.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's less accepting of signed char ... insisting that e.g. tolower()
not receive one as a parameter.
It's probably good to phase out such usage, given the number of bugs
that lurk in the vicinity (assumptions that char is unsigned), so fix
these even though such usage is actually legal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Misc:
- Introduce some "struct reg" temporaries, for clarity
- Shorten lines
- Add some missing whitespace
- Clean up comments
- Add notes about some fault handling issues
- Most of these errata workarounds are for *OLD* chip revisions
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
And add my copyright. MPCore is untested, but it's the
only other ARM11 core to care about.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Command "reset halt" checks if PC properly resets, issueing warning:
"PC was not 0. Does this target need srst_pulls_trst?".
Checking PC against 0 is not always correct.
Removed PC value check, as suggested by Øyvind Harboe.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: U-PROPRIET-28D9DF\PROPRIETAIRE <PROPRIETAIRE@propriet-28d9df.(none)>
This creates the TCL interface for configuring an AT91SAM9 NAND flash
controller and implements the necessary functions to correctly work with
a NAND flash device connected to the chip. This includes updates to the
driver list and the Makefile.am to support building the driver and also
houses the documentation update in openocd.texi.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
In conjunction with manual register setup, this lets the ETM trigger
cause entry to debug state. It should make it easier to test and
bugfix the ETM code, by enabling non-trace usage and isolating bugs
specific to thef ETM support. (One current issue being that trace
data collection using the ETB doesn't yet behave.)
For example, many ARM9 cores with an ETM should be able to implement
four more (simple) breakpoints and two more (simple) watchpoints than
the EmbeddedICE supports. Or, they should be able to support complex
breakpoints, incorporating ETM sequencer, counters, and/or subroutine
entry/exit criteria int criteria used to trigger debug entry.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
