Config file renamed to ke0x.cfg and a notice added to texi.
While on ke0x.cfg CPUTAPID setting fixed: device has SWD port only, no JTAG.
Removed per device configs as they set CHIPNAME and nothing more.
Let's use reasonably universal chip name 'ke' set in family config.
Change-Id: I313db87a59f25f968eb3c27df155780b67becee8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3897
Tested-by: jenkins
Reviewed-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The new Kinetis KE1x families use FTFE flash controller unlike KE0x.
Also SDID coding corresponds to new K, KL and KV families.
That's why KE1x is handled by kinetis driver instead of kinetis_ke
Change-Id: Ibb73e28e41dfbb086e761e1f006b089825dab854
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3896
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Supported SoCs: AR71xx, AR724x, AR91xx, AR93xx, QCA9558
Extended and revised version of my original patch submitted by Dmytro
here: http://openocd.zylin.com/#/c/3390
This driver is using pure SPI mode, so the flash base address is not
used except some flash commands (e.g. "flash program") need it to
distinguish the banks.
Example config with all 3 chip selects:
flash bank flash0 ath79 0 0 0 0 $_TARGETNAME cs0
flash bank flash1 ath79 0x10000000 0 0 0 $_TARGETNAME cs1
flash bank flash2 ath79 0x20000000 0 0 0 $_TARGETNAME cs2
Example usage:
> flash probe flash0
Found flash device 'win w25q128fv' (ID 0x001840ef)
flash 'ath79' found at 0x00000000
> flash probe flash1
No SPI flash found
> flash probe flash2
No SPI flash found
> flash banks
> flash read_bank flash0 /tmp/test.bin 0x00000000 0x1000
reading 4096 bytes from flash @0x00000000
wrote 4096 bytes to file /tmp/test.bin from flash bank 0 at offset
0x00000000 in 28.688066s (0.139 KiB/s)
Change-Id: I5feb697722c07e83a9c1b361a9db7b06bc699aa8
Signed-off-by: Tobias Diedrich <ranma+openocd@tdiedrich.de>
Reviewed-on: http://openocd.zylin.com/3612
Tested-by: jenkins
Reviewed-by: Dmytro <dioptimizer@hotmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
For some targets (like nrf51) sysfs driver is too slow. This
patch implements memory maped driver for IMX processors.
Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should
work on any NXP IMX CPU.
Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7
Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com>
Reviewed-on: http://openocd.zylin.com/4106
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a driver for the SWD-only Cypress KitProg
programmer/debugger.
Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make the 'offset' parameter optional, if omitted simply start at the
beginning of the flash bank.
Additionally, check if the argument is out of bounds of the flash bank.
Change-Id: Id1959eee5c395666c35f26342c3c50134dd564e5
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3858
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 77a1c01ccb introduced infrastructure
for utilizing protection blocks of different size than erase sector.
Parts of doc/help kept reading 'sector' instead of 'protection block'.
flash_driver_protect() parameter range testing did not switched
to bank->num_prot_blocks.
This change fixes it.
Change-Id: Iec301761190a1a1bcc4cb005a519b9e5e4fede51
Reported-by: Mark Odell <mark@odell.ws>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3917
Tested-by: jenkins
Reviewed-by: Mark Odell <mrfirmware@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Fix typo and a sentence that sounds strange since the ft2232 driver
was removed.
Add documentation for the SWD signal usage.
Remove the text mentioning a default VID:PID which doesn't exist.
Change-Id: I27eba571f2f7c46bdb6ae623ab285595018e99d9
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3935
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
EMUCOM is a way to communicate with a J-Link device via so called
channels. A channel can either be read or written in a single
operation.
Beside the reserved channels for SEGGER, there are channels available to
implement vendor and/or device specific functionalities. For example,
EMUCOM is used on many starter and development kits from Silicon Labs to
access power measurements and various other information and settings.
Change-Id: I6094109c043b34aed4a40ceabe71f30ff896bf1d
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3794
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a Cortex-M private configuration option
that allows setting the acess point during target
creation. This circumvents situations in hybrid systems
when the correct access point can not be automatically
detected.
Change-Id: If313a5250e6e66509bb9080f3498feab7781dced
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3639
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The Cypress CY7C65215 Dual Channel USB-Serial Bridge Controller [1]
understands the OpenJTAG protocol over a proprietary USB interface.
This patch adds support for the CY7C65215 to the openjtag interface
driver. A new configuration option, `openjtag_variant`, allows to
select the transport to use.
Libusb (1.x or 0.1) is now a hard dependency of the openjtag driver.
This should not be a big issue as libftdi also depends on it.
[1] http://www.cypress.com/?rID=82870
Change-Id: I55ffb3fd9e006eb311e405d9fb836bb119644bfd
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-on: http://openocd.zylin.com/2805
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds support for bridging semihosting to GDB's File-I/O
remote protocol extension. For the most part operations match up 1:1,
however some require a working area to complete successfully, namely
operations that devolve to read, stat, and gettimeofday.
A new command was added to enable support for fileio named `arm
semihosting_fileio`, which ensures that the default behavior remains
intact for those that prefer it.
Finally, redundant logging was removed from the target_arch_state
function; this permits ARM targets to quiesce log output when polling
for a fileio reply. This prevents filling the logs with halt/resume
messages when using semihosting fileio.
Change-Id: Ifbb864fc2373336a501cc0332675b887b552e1ee
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3566
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch introduces RTOS support for uC/OS-III. Currently, only
FPU-less ARM Cortex-M targets are supported. Due to the configurability
of the RTOS, an OpenOCD-specific file must be linked along with the
project to determine the correct offsets within the OS_TCB structure.
In addition to the above, a crash was fixed in rtos_get_gdb_reg_list
such that RTOS support could be used between resets without restarting
OpenOCD and support for the Hg packet was cleaned up.
Change-Id: Ide004a689e6b886185df665c00fb644629eb31d1
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3556
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The '-defer-examine' option to target create allows declaring targets
that are present on the chain, but not fully functional. They will
be skipped by the initial arp_examine as well as arp_examine after
reset.
Manual examine using 'arp_examine' is needed to examine them, with the
idea that some kind of actions is neeed to bring them to a state where
examine will succeed (if at all possible).
In order to allow value less options to target command, I had to relax
the goi.argc check in jim_target_configure().
Change-Id: I9bf4e8d27eb6476dd9353d15f48965a8cfd5c122
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3076
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Purge all legacy interface configurations so there's no more confusion
over which one to use.
Also remove doc/INSTALL.txt which mentions ft2232 but otherwise just
duplicates what INSTALL says.
Change-Id: Ic94f808f123d4917e600b79309f1272c78a7bb11
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3236
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Since OpenOCD doesn't fit most common definitions of the word "daemon",
using it in the documentation is confusing.
Reported by IRC user ohsix.
Change-Id: I688d722771b084b17c2a7af8e83fd64bab6141b8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3634
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
As per the documentation, used "disabled" as the value to disable, as this
is the same value to disable the telnet and tcl server.
Change-Id: Idc4a8580098ec1107dcc6e1f59e817ecdebc38ac
Signed-off-by: Sandeep Mistry <s.mistry@arduino.cc>
Reviewed-on: http://openocd.zylin.com/3175
Tested-by: jenkins
Reviewed-by: Cristian Maglie
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Kinetis family employs strange concept of Flash Configuration Field at
address 0x400 of program flash. Writing incorrect data to FCF may
permanently lock the device.
The change introduces 'kinetis fcf_source protection' mode. In this mode
write of flash image data to FCF is prevented. FCF data build from
protection (set by 'flash protect' command) are written instead.
FCF data are written also just after erase of relevant sector. It
protects device from locking security by reset or power cycle after erase.
prot_blocks array is used as protection blocks have bigger size than sectors.
Alignment and padding programming sections is rewritten to fix
writing with not section boundary aligned begin.
Change-Id: I9fc8bd37d6f627fb8ed7abb7f7560e78a740b195
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3562
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Originally flash/nor infrastructure assumed protection blocks identical
to erase sectors. This assumption is not valid for many flash types.
Driver code fixed the problem either by increasing sector size to
size of protection block or by defining more protection block than
really existed in device. Both cases had drawbacks.
The change retains compatibility with the old driver.
Updated driver can set protection blocks table independent
of sector table.
Change-Id: I27f6d267528ad9ed9fe0a85f05436a8ec17603a4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3545
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
