Use the correct enum name in its kernel-doc heading.
Add ending ':' to struct member names.
Drop the @id: kernel-doc entry since there is no struct member named 'id'.
edma.h:46: warning: expecting prototype for struct dw_edma_core_ops.
Prototype was for struct dw_edma_plat_ops instead
Warning: edma.h:101 struct member 'ops' not described in 'dw_edma_chip'
Warning: edma.h:101 struct member 'flags' not described in 'dw_edma_chip'
Warning: edma.h:101 struct member 'reg_base' not described
in 'dw_edma_chip'
Warning: edma.h:101 struct member 'll_wr_cnt' not described
in 'dw_edma_chip'
Warning: edma.h:101 struct member 'll_rd_cnt' not described
in 'dw_edma_chip'
Warning: edma.h:101 struct member 'll_region_wr' not described
in 'dw_edma_chip'
Warning: edma.h:101 struct member 'll_region_rd' not described
in 'dw_edma_chip'
Warning: edma.h:101 struct member 'dt_region_wr' not described
in 'dw_edma_chip'
Warning: edma.h:101 struct member 'dt_region_rd' not described
in 'dw_edma_chip'
Warning: edma.h:101 struct member 'mf' not described in 'dw_edma_chip'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20251101191524.1991135-1-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The user of k3_udma_glue_reset_rx_chn() e.g. ti_am65_cpsw_nuss can
run on multiple platforms having different DMA architectures.
On some platforms there can be one FDQ for all flows in the RX channel
while for others there is a separate FDQ for each flow in the RX channel.
So far we have been relying on the skip_fdq argument of
k3_udma_glue_reset_rx_chn().
Instead of relying on the user to provide this information, infer it
based on DMA architecture during k3_udma_glue_request_rx_chn() and save it
in an internal flag 'single_fdq'. Use that flag at
k3_udma_glue_reset_rx_chn() to deicide if the FDQ needs
to be cleared for every flow or just for flow 0.
Fixes the below issue on ti_am65_cpsw_nuss driver on AM62-SK.
> ip link set eth1 down
> ip link set eth0 down
> ethtool -L eth0 rx 8
> ip link set eth0 up
> modprobe -r ti_am65_cpsw_nuss
[ 103.045726] ------------[ cut here ]------------
[ 103.050505] k3_knav_desc_pool size 512000 != avail 64000
[ 103.050703] WARNING: CPU: 1 PID: 450 at drivers/net/ethernet/ti/k3-cppi-desc-pool.c:33 k3_cppi_desc_pool_destroy+0xa0/0xa8 [k3_cppi_desc_pool]
[ 103.068810] Modules linked in: ti_am65_cpsw_nuss(-) k3_cppi_desc_pool snd_soc_hdmi_codec crct10dif_ce snd_soc_simple_card snd_soc_simple_card_utils display_connector rtc_ti_k3 k3_j72xx_bandgap tidss drm_client_lib snd_soc_davinci_mcas
p drm_dma_helper tps6598x phylink snd_soc_ti_udma rti_wdt drm_display_helper snd_soc_tlv320aic3x_i2c typec at24 phy_gmii_sel snd_soc_ti_edma snd_soc_tlv320aic3x sii902x snd_soc_ti_sdma sa2ul omap_mailbox drm_kms_helper authenc cfg80211 r
fkill fuse drm drm_panel_orientation_quirks backlight ip_tables x_tables ipv6 [last unloaded: k3_cppi_desc_pool]
[ 103.119950] CPU: 1 UID: 0 PID: 450 Comm: modprobe Not tainted 6.13.0-rc7-00001-g9c5e3435fa66 #1011
[ 103.119968] Hardware name: Texas Instruments AM625 SK (DT)
[ 103.119974] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 103.119983] pc : k3_cppi_desc_pool_destroy+0xa0/0xa8 [k3_cppi_desc_pool]
[ 103.148007] lr : k3_cppi_desc_pool_destroy+0xa0/0xa8 [k3_cppi_desc_pool]
[ 103.154709] sp : ffff8000826ebbc0
[ 103.158015] x29: ffff8000826ebbc0 x28: ffff0000090b6300 x27: 0000000000000000
[ 103.165145] x26: 0000000000000000 x25: 0000000000000000 x24: ffff0000019df6b0
[ 103.172271] x23: ffff0000019df6b8 x22: ffff0000019df410 x21: ffff8000826ebc88
[ 103.179397] x20: 000000000007d000 x19: ffff00000a3b3000 x18: 0000000000000000
[ 103.186522] x17: 0000000000000000 x16: 0000000000000000 x15: 000001e8c35e1cde
[ 103.193647] x14: 0000000000000396 x13: 000000000000035c x12: 0000000000000000
[ 103.200772] x11: 000000000000003a x10: 00000000000009c0 x9 : ffff8000826eba20
[ 103.207897] x8 : ffff0000090b6d20 x7 : ffff00007728c180 x6 : ffff00007728c100
[ 103.215022] x5 : 0000000000000001 x4 : ffff000000508a50 x3 : ffff7ffff6146000
[ 103.222147] x2 : 0000000000000000 x1 : e300b4173ee6b200 x0 : 0000000000000000
[ 103.229274] Call trace:
[ 103.231714] k3_cppi_desc_pool_destroy+0xa0/0xa8 [k3_cppi_desc_pool] (P)
[ 103.238408] am65_cpsw_nuss_free_rx_chns+0x28/0x4c [ti_am65_cpsw_nuss]
[ 103.244942] devm_action_release+0x14/0x20
[ 103.249040] release_nodes+0x3c/0x68
[ 103.252610] devres_release_all+0x8c/0xdc
[ 103.256614] device_unbind_cleanup+0x18/0x60
[ 103.260876] device_release_driver_internal+0xf8/0x178
[ 103.266004] driver_detach+0x50/0x9c
[ 103.269571] bus_remove_driver+0x6c/0xbc
[ 103.273485] driver_unregister+0x30/0x60
[ 103.277401] platform_driver_unregister+0x14/0x20
[ 103.282096] am65_cpsw_nuss_driver_exit+0x18/0xff4 [ti_am65_cpsw_nuss]
[ 103.288620] __arm64_sys_delete_module+0x17c/0x25c
[ 103.293404] invoke_syscall+0x44/0x100
[ 103.297149] el0_svc_common.constprop.0+0xc0/0xe0
[ 103.301845] do_el0_svc+0x1c/0x28
[ 103.305155] el0_svc+0x28/0x98
[ 103.308207] el0t_64_sync_handler+0xc8/0xcc
[ 103.312384] el0t_64_sync+0x198/0x19c
[ 103.316040] ---[ end trace 0000000000000000 ]---
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20250224-k3-udma-glue-single-fdq-v2-1-cbe7621f2507@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When this file was renamed in commit b8a6d9980f ("dma: ipu: rename
mach/ipu.h to include/linux/dma/ipu-dma.h"), 4 .c files have been modified
accordingly:
drivers/dma/ipu/ipu_idmac.c
drivers/dma/ipu/ipu_irq.c
--> removed in commit f1de55ff7c ("dmaengine: ipu: Remove the driver")
in 2023-08
drivers/media/platform/soc_camera/mx3_camera.c
--> removed in commit c93cc61475 ("[media] staging/media: remove
deprecated mx3 driver") in 2016-06
drivers/video/mx3fb.c
--> removed in commit bfac19e239 ("fbdev: mx3fb: Remove the driver")
in 2023-08
Now include/linux/dma/ipu-dma.h is unused and can be removed as-well.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/532e7e2816ccf226f3ab1fa76ec7873bc09299d0.1724258714.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing function k3_udma_glue_request_remote_rx_chn() supports
requesting an RX DMA channel and flow by the name of the RX DMA channel.
Add support to request RX DMA channel for a given thread ID in the form of
a new function named k3_udma_glue_request_remote_rx_chn_for_thread_id().
Also, export it for use by drivers which are probed by alternate methods
(non device-tree) but still wish to make use of the existing DMA APIs. Such
drivers could be informed about the thread ID corresponding to the RX DMA
channel by RPMsg for example.
Since the new function k3_udma_glue_request_remote_rx_chn_for_thread_id()
reuses most of the code in k3_udma_glue_request_remote_rx_chn(), create a
new function named k3_udma_glue_request_remote_rx_chn_common() for the
common code.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20240124124319.820002-5-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing function k3_udma_glue_request_tx_chn() supports requesting
a TX DMA channel by its name. Add a new function to request TX DMA channel
for a given thread ID, named k3_udma_glue_request_tx_chn_for_thread_id().
Also, export it for use by drivers which are probed by alternate methods
(non device-tree) but still wish to make use of the existing DMA APIs. Such
drivers could be informed about the thread ID corresponding to the TX DMA
channel by RPMsg for example.
Since the new function k3_udma_glue_request_tx_chn_for_thread_id() reuses
most of the code in k3_udma_glue_request_tx_chn(), create a new function
for the common code, named k3_udma_glue_request_tx_chn_common().
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20240124124319.820002-4-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for HDMA NATIVE, as long the IP design has set
the compatible register map parameter-HDMA_NATIVE,
which allows compatibility for native HDMA register configuration.
The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP.
And the native HDMA registers are different from eDMA, so this patch
add support for HDMA NATIVE mode.
HDMA write and read channels operate independently to maximize
the performance of the HDMA read and write data transfer over
the link When you configure the HDMA with multiple read channels,
then it uses a round robin (RR) arbitration scheme to select
the next read channel to be serviced.The same applies when you
have multiple write channels.
The native HDMA driver also supports a maximum of 16 independent
channels (8 write + 8 read), which can run simultaneously.
Both SAR (Source Address Register) and DAR (Destination Address Register)
are aligned to byte.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230520050854.73160-4-cai.huoqing@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The dw_edma_core_ops structure contains a set of the operations:
device IRQ numbers getter, CPU/PCI address translation. Based on the
functions semantics the structure name "dw_edma_plat_ops" looks more
descriptive since indeed the operations are platform-specific. The
"dw_edma_core_ops" name shall be used for a structure with the IP-core
specific set of callbacks in order to abstract out DW eDMA and DW HDMA
setups. Such structure will be added in one of the next commit in the
framework of the set of changes adding the DW HDMA device support.
Anyway the renaming was necessary to distinguish two types of
the implementation callbacks:
1. DW eDMA/hDMA IP-core specific operations: device-specific CSR
setups in one or another aspect of the DMA-engine initialization.
2. DW eDMA/hDMA platform specific operations: the DMA device
environment configs like IRQs, address translation, etc.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230520050854.73160-2-cai.huoqing@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Per [1], UDMA TR15 transactions may hang if ICNT0 is less than 64B
Work around is to set EOL flag is to 1 for ICNT0.
Since, there is no performance penalty / side effects of setting EOL
flag event ICNTO > 64B, just set the flag for all UDMAP TR15
descriptors.
[1] https://www.ti.com/lit/er/sprz455a/sprz455a.pdf
Errata doc for J721E DRA829/TDA4VM Processors Silicon Revision 1.1/1.0
(Rev. A)
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[j-choudhary@ti.com: minor cleanups]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20230323120107.27638-1-j-choudhary@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull dmaengine updates from Vinod Koul:
"A new driver, couple of device support and binding conversion along
with bunch of driver updates are the main features of this.
New hardware support:
- TI AM62Ax controller support
- Xilinx xdma driver
- Qualcomm SM6125, SM8550, QDU1000/QRU1000 GPI controller
Updates:
- Runtime pm support for at_xdmac driver
- IMX sdma binding conversion to yaml and HDMI audio support
- IMX mxs binding conversion to yaml"
* tag 'dmaengine-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (35 commits)
dmaengine: idma64: Update bytes_transferred field
dmaengine: imx-sdma: Set DMA channel to be private
dmaengine: dw: Move check for paused channel to dwc_get_residue()
dmaengine: ptdma: check for null desc before calling pt_cmd_callback
dmaengine: dw-axi-dmac: Do not dereference NULL structure
dmaengine: idxd: Fix default allowed read buffers value in group
dmaengine: sf-pdma: pdma_desc memory leak fix
dmaengine: Simplify dmaenginem_async_device_register() function
dmaengine: use sysfs_emit() to instead of scnprintf()
dmaengine: Make an order in struct dma_device definition
dt-bindings: dma: cleanup examples - indentation, lowercase hex
dt-bindings: dma: drop unneeded quotes
dmaengine: xilinx: xdma: Add user logic interrupt support
dmaengine: xilinx: xdma: Add xilinx xdma driver
dmaengine: drivers: Use devm_platform_ioremap_resource()
dmaengine: at_xdmac: remove empty line
dmaengine: at_xdmac: add runtime pm support
dmaengine: at_xdmac: align properly function members
dmaengine: ppc4xx: Convert to use sysfs_emit()/sysfs_emit_at() APIs
dmaengine: sun6i: Set the maximum segment size
...
When CONFIG_DW_EDMA=m, dw_edma_probe() is built as a module. Previously
edma.h declared it as extern, but the implementation isn't available for
builtin callers. A subsequent commit will add calls from
dw_pcie_host_init() and dw_pcie_ep_init(), which can only be built-in.
Make it safe for such builtin callers to call dw_edma_probe() by using
IS_REACHABLE() to define a stub when CONFIG_DW_EDMA=m.
When CONFIG_DW_EDMA=m, these builtin callers will fail to detect and
register eDMA devices, so eDMA won't be usable even if the dw-edma module
is loaded.
[bhelgaas: split to separate patch, commit log]
Link: https://lore.kernel.org/r/20230113171409.30470-25-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Currently the DW eDMA driver only supports the linked lists memory
allocated locally with respect to the remote eDMA engine setup. It means
the linked lists will be accessible by the CPU via the MMIO space only. If
eDMA is embedded into the DW PCIe Root Ports or local Endpoints (which
support will be added in subsequent commits) the linked lists are supposed
to be allocated in the CPU memory. In that case the LL-entries can be
directly accessed, while the former case implies using the MMIO accessors
for that.
In order to have both cases supported by the driver, the dw_edma_region
descriptor should be fixed to contain the MMIO-backed and just memory-based
virtual addresses. The linked lists initialization procedure will use one
of them depending on the eDMA device nature. If the eDMA engine is embedded
into the local DW PCIe Root Port/Endpoint controllers, the list entries
will be directly accessed by referencing the corresponding structure
fields. Otherwise the MMIO accessors usage will be preserved.
Link: https://lore.kernel.org/r/20230113171409.30470-24-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Using an abstract number as the DW eDMA chip identifier isn't practical
because there can be more than one DW eDMA controller on the platform. Some
may be detected as the PCIe Endpoints, and others may be embedded in DW
PCIe Root Port/Endpoint controllers. An abstract number in, for instance,
the IRQ handlers list, doesn't give a notion regarding their reference to
the particular DMA controller.
To preserve the code simplicity and support multi-eDMA platforms, use the
parental device name to create the DW eDMA controller name.
Link: https://lore.kernel.org/r/20230113171409.30470-22-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Since 9575632052 ("dmaengine: make slave address physical"), the source
and destination addresses of the DMA slave device have been converted to
physical addresses in the CPU address space. It's the DMA device driver's
responsibility to convert them to the DMA bus address space. In case of the
DW eDMA device, the source or destination peripheral (slave) devices reside
in PCI bus space. Thus we need to perform the PCI Host/Endpoint windows-
based (i.e. DT "ranges" property) address translation; otherwise the eDMA
transactions won't work as expected (or can be even harmful) if the CPU and
PCI address spaces don't match.
Note 1: Even though the DMA interleaved template has both source and
destination addresses declared as dma_addr_t, only the CPU memory range
should be mapped to be seen by the DMA device since it's a subject of the
DMA getting towards the system side. The device part must not be mapped
since the slave device resides in the PCI bus space, which isn't affected
by IOMMUs or iATU translations. DW PCIe eDMA generates corresponding
MWr/MRd TLPs on its own.
Note 2: This functionality is mainly required for the remote eDMA setup
since the CPU address must be manually translated into the PCI bus space
before being written to LLI.{SAR,DAR}. If eDMA is embedded in the locally
accessible DW PCIe Root Port/Endpoint, software-based translation isn't
required since hardware will translate it via the Outbound iATU as long as
the DMA_BYPASS flag is cleared. If DMA_BYPASS is set or there is no
Outbound iATU entry that contains the SAR or DAR (for Read and Write
channel respectively), there won't be any translation performed but DMA
will proceed with the corresponding source/destination address as-is.
Link: https://lore.kernel.org/r/20230113171409.30470-8-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
The dw_edma_region.paddr field should be a memory base address visible by
the DW eDMA controller. If the DMA engine is embedded in the DW PCIe
Host/Endpoint controller, the address should belong to the Local CPU/
Application memory. If eDMA is remotely accessible across the PCI bus via
PCI memory IOs, the address should be part of the PCI bus memory space.
The latter case hasn't been well covered in the corresponding glue-driver.
Since pci_dev.resource[] contains resources defined in the CPU memory
space, they need to be converted to the PCI bus address space. Convert the
LL, DT and CSRs PCI memory ranges with pci_bus_address().
In addition, extend the dw_edma_region.paddr field size. The field normally
contains a memory range base address to be set in the DW eDMA Linked-List
pointer register or as a base address of the Linked-List data buffer. In
accordance with [1] the LL range is supposed to be created in the Local
CPU/Application memory, but depending on the DW eDMA utilization the memory
can be created as a part of the PCI bus address space (as in the case of
the DW PCIe Endpoint prototype kit).
In the former case dw_edma_region.paddr should be a dma_addr_t, while in
the latter one it should be a pci_bus_addr_t. Since the corresponding CSRs
are always 64 bits wide, convert dw_edma_region.paddr to be u64, and let
the client make sure it has a valid address visible by the DW eDMA
controller. For instance, the DW eDMA PCIe glue-driver initializes the
field with addresses from the PCI bus memory space.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v.5.40a, March 2019, p.1103
Link: https://lore.kernel.org/r/20230113171409.30470-4-Sergey.Semin@baikalelectronics.ru
Fixes: 41aaff2a2a ("dmaengine: Add Synopsys eDMA IP PCIe glue-logic")
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
The hdmi script already supported in sdma firmware. So add support hdmi
in sdma driver.
The design of hdmi script is different from common script such as sai.
There is no need to config buffer descriptor for HDMI. The cyclic
capability is achieved by the hdmi script. The slave config is so simple,
only config src_addr, dts_addr and direction DMA_TRANS_NONE.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221115093823.2879128-3-joy.zou@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Consolidate duplicated 'next function' scanning and extend to allow
'isolated functions' on s390, similar to existing hypervisors
(Niklas Schnelle)
Resource management:
- Implement pci_iobar_pfn() for sparc, which allows us to remove the
sparc-specific pci_mmap_page_range() and pci_mmap_resource_range().
This removes the ability to map the entire PCI I/O space using
/proc/bus/pci, but we believe that's already been broken since
v2.6.28 (Arnd Bergmann)
- Move common PCI definitions to asm-generic/pci.h and rework others
to be be more specific and more encapsulated in arches that need
them (Stafford Horne)
Power management:
- Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef
CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas)
Virtualization:
- Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate
the functions but don't advertise an ACS capability (Pavan Chebbi)
Error handling:
- Clear PCI Status register during enumeration in case firmware left
errors logged (Kai-Heng Feng)
- When we have native control of AER, enable error reporting for all
devices that support AER. Previously only a few drivers enabled
this (Stefan Roese)
- Keep AER error reporting enabled for switches. Previously we
enabled this during enumeration but immediately disabled it (Stefan
Roese)
- Iterate over error counters instead of error strings to avoid
printing junk in AER sysfs counters (Mohamed Khalfella)
ASPM:
- Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g.,
via sysfs, are not lost across power state changes (Kai-Heng Feng)
Endpoint framework:
- Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)
Endpoint embedded DMA controller driver:
- Simplify and clean up support for the DesignWare embedded DMA
(eDMA) controller (Frank Li, Serge Semin)
Broadcom STB PCIe controller driver:
- Avoid config space accesses when link is down because we can't
recover from the CPU aborts these cause (Jim Quinlan)
- Look for power regulators described under Root Ports in DT and
enable them before scanning the secondary bus (Jim Quinlan)
- Disable/enable regulators in suspend/resume (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Simplify and clean up clock and PHY management (Richard Zhu)
- Disable/enable regulators in suspend/resume (Richard Zhu)
- Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)
- Allow speeds faster than Gen2 (Richard Zhu)
- Make link being down a non-fatal error so controller probe doesn't
fail if there are no Endpoints connected (Richard Zhu)
Loongson PCIe controller driver:
- Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)
- Avoid config reads to non-existent LS2K/LS7A devices because a
hardware defect causes machine hangs (Huacai Chen)
- Work around LS7A integrated devices that report incorrect Interrupt
Pin values (Jianmin Lv)
Marvell Aardvark PCIe controller driver:
- Add support for AER and Slot capability on emulated bridge (Pali
Rohár)
MediaTek PCIe controller driver:
- Add Airoha EN7532 to DT binding (John Crispin)
- Allow building of driver for ARCH_AIROHA (Felix Fietkau)
MediaTek PCIe Gen3 controller driver:
- Print decoded LTSSM state when the link doesn't come up (Jianjun
Wang)
NVIDIA Tegra194 PCIe controller driver:
- Convert DT binding to json-schema (Vidya Sagar)
- Add DT bindings and driver support for Tegra234 Root Port and
Endpoint mode (Vidya Sagar)
- Fix some Root Port interrupt handling issues (Vidya Sagar)
- Set default Max Payload Size to 256 bytes (Vidya Sagar)
- Fix Data Link Feature capability programming (Vidya Sagar)
- Extend Endpoint mode support to devices beyond Controller-5 (Vidya
Sagar)
Qualcomm PCIe controller driver:
- Rework clock, reset, PHY power-on ordering to avoid hangs and
improve consistency (Robert Marko, Christian Marangi)
- Move pipe_clk handling to PHY drivers (Dmitry Baryshkov)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
- Add support for more than 32 MSI interrupts (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Convert DT binding to json-schema (Herve Codina)
- Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver
(Herve Codina)
Samsung Exynos PCIe controller driver:
- Fix phy-exynos-pcie driver so it follows the 'phy_init() before
phy_power_on()' PHY programming model (Marek Szyprowski)
Synopsys DesignWare PCIe controller driver:
- Simplify and clean up the DWC core extensively (Serge Semin)
- Fix an issue with programming the ATU for regions that cross a 4GB
boundary (Serge Semin)
- Enable the CDM check if 'snps,enable-cdm-check' exists; previously
we skipped it if 'num-lanes' was absent (Serge Semin)
- Allocate a 32-bit DMA-able page to be MSI target instead of using a
driver data structure that may not be addressable with 32-bit
address (Will McVicker)
- Add DWC core support for more than 32 MSI interrupts (Dmitry
Baryshkov)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Versal CPM5 Gen5 Root Port
(Bharat Kumar Gogada)"
* tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits)
PCI: imx6: Support more than Gen2 speed link mode
PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
PCI: imx6: Reformat suspend callback to keep symmetric with resume
PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
PCI: imx6: Disable clocks in reverse order of enable
PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
PCI: imx6: Reduce resume time by only starting link if it was up before suspend
PCI: imx6: Mark the link down as non-fatal error
PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
PCI: imx6: Turn off regulator when system is in suspend mode
PCI: imx6: Call host init function directly in resume
PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
PCI: imx6: Propagate .host_init() errors to caller
PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
PCI: imx6: Factor out ref clock disable to match enable
PCI: imx6: Move imx6_pcie_clk_disable() earlier
PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
PCI: imx6: Move PHY management functions together
PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
...
The peripheral may have several FIFOs, but some case just select
some FIFOs from them for data transfer, which means FIFO0 and FIFO2
may be selected. So add FIFO address stride support, 0 means all FIFOs
are continuous, 1 means 1 word stride between FIFOs. All stride between
FIFOs should be same.
Another option words_per_fifo means how many audio channel data copied
to one FIFO one time, 1 means one channel per FIFO, 2 means 2 channels
per FIFO.
If 'n_fifos_src = 4' and 'words_per_fifo = 2', it means the first two
words(channels) fetch from FIFO0 and then jump to FIFO1 for next two words,
and so on after the last FIFO3 fetched, roll back to FIFO0.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1657162829-9273-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Randy Dunlap
Roger Quadros
Yue Haibing
Christophe JAILLET
Robin Gong
Siddharth Vadapalli
Cai Huoqing
Vignesh Raghavendra
Linus Torvalds
Serge Semin
Lizhi Hou
Joy Zou
Andy Shevchenko
Shengjiu Wang
Julia Lawall
Frank Li