ktime.h pulls in quite a few headers recursively (including printk.h) -
this is going to help with trimming sched.h dependencies.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Pull timekeeping and timer updates from Thomas Gleixner:
"Core:
- Consolidation of the vDSO build infrastructure to address the
difficulties of cross-builds for ARM64 compat vDSO libraries by
restricting the exposure of header content to the vDSO build.
This is achieved by splitting out header content into separate
headers. which contain only the minimaly required information which
is necessary to build the vDSO. These new headers are included from
the kernel headers and the vDSO specific files.
- Enhancements to the generic vDSO library allowing more fine grained
control over the compiled in code, further reducing architecture
specific storage and preparing for adopting the generic library by
PPC.
- Cleanup and consolidation of the exit related code in posix CPU
timers.
- Small cleanups and enhancements here and there
Drivers:
- The obligatory new drivers: Ingenic JZ47xx and X1000 TCU support
- Correct the clock rate of PIT64b global clock
- setup_irq() cleanup
- Preparation for PWM and suspend support for the TI DM timer
- Expand the fttmr010 driver to support ast2600 systems
- The usual small fixes, enhancements and cleanups all over the
place"
* tag 'timers-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (80 commits)
Revert "clocksource/drivers/timer-probe: Avoid creating dead devices"
vdso: Fix clocksource.h macro detection
um: Fix header inclusion
arm64: vdso32: Enable Clang Compilation
lib/vdso: Enable common headers
arm: vdso: Enable arm to use common headers
x86/vdso: Enable x86 to use common headers
mips: vdso: Enable mips to use common headers
arm64: vdso32: Include common headers in the vdso library
arm64: vdso: Include common headers in the vdso library
arm64: Introduce asm/vdso/processor.h
arm64: vdso32: Code clean up
linux/elfnote.h: Replace elf.h with UAPI equivalent
scripts: Fix the inclusion order in modpost
common: Introduce processor.h
linux/ktime.h: Extract common header for vDSO
linux/jiffies.h: Extract common header for vDSO
linux/time64.h: Extract common header for vDSO
linux/time32.h: Extract common header for vDSO
linux/time.h: Extract common header for vDSO
...
The vDSO library should only include the necessary headers required for
a userspace library (UAPI and a minimal set of kernel headers). To make
this possible it is necessary to isolate from the kernel headers the
common parts that are strictly necessary to build the library.
Split ktime.h into linux and common headers to make the latter suitable
for inclusion in the vDSO library.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200320145351.32292-15-vincenzo.frascino@arm.com
The interfaces based on 'struct timespec' and 'unsigned long' seconds
are no longer recommended for new code, and we are trying to migrate to
ktime_t based interfaces and other y2038-safe variants.
This moves all the legacy interfaces from linux/timekeeping.h into a
new timekeeping32.h to better document this.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
No point in going through loops and hoops instead of just comparing the
values.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
It was noted that the 32bit implementation of ktime_divns()
was doing unsigned division and didn't properly handle
negative values.
And when a ktime helper was changed to utilize
ktime_divns, it caused a regression on some IR blasters.
See the following bugzilla for details:
https://bugzilla.redhat.com/show_bug.cgi?id=1200353
This patch fixes the problem in ktime_divns by checking
and preserving the sign bit, and then reapplying it if
appropriate after the division, it also changes the return
type to a s64 to make it more obvious this is expected.
Nicolas also pointed out that negative dividers would
cause infinite loops on 32bit systems, negative dividers
is unlikely for users of this function, but out of caution
this patch adds checks for negative dividers for both
32-bit (BUG_ON) and 64-bit(WARN_ON) versions to make sure
no such use cases creep in.
[ tglx: Hand an u64 to do_div() to avoid the compiler warning ]
Fixes: 166afb6451 'ktime: Sanitize ktime_to_us/ms conversion'
Reported-and-tested-by: Trevor Cordes <trevor@tecnopolis.ca>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1431118043-23452-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull time updates from John Stultz for 3.20:
* ktime division optimization
* Expose a few more y2038-safe timekeeping interfaces
* RTC core changes to address y2038
At least on ARM, do_div() is optimized to turn constant divisors into
an inline multiplication by the reciprocal value at compile time.
However this optimization is missed entirely whenever ktime_divns() is
used and the slow out-of-line division code is used all the time.
Let ktime_divns() use do_div() inline whenever the divisor is constant
and small enough. This will make things like ktime_to_us() and
ktime_to_ms() much faster.
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Nicolas Pitre <nico@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Right now we have time related prototypes in 3 different header
files. Move it to a single timekeeping header file and move the core
internal stuff into a core private header.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In order to support dates past 2038 on 32bit systems, ktime_set()
needs to handle 64bit second values.
[ tglx: Removed the BITS_PER_LONG check ]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
With the plain nanoseconds based ktime_t we can simply use
ktime_divns() instead of going through loops and hoops of
timespec/timeval conversion.
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The non-scalar ktime_t implementation is basically a timespec
which has to be changed to support dates past 2038 on 32bit
systems.
This patch removes the non-scalar ktime_t implementation, forcing
the scalar s64 nanosecond version on all architectures.
This may have additional performance overhead on some 32bit
systems when converting between ktime_t and timespec structures,
however the majority of 32bit systems (arm and i386) were already
using scalar ktime_t, so no performance regressions will be seen
on those platforms.
On affected platforms, I'm open to finding optimizations, including
avoiding converting to timespecs where possible.
[ tglx: We can now cleanup the ktime_t.tv64 mess, but thats a
different issue and we can throw a coccinelle script at it ]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Add two minimal helper functions analogous to time_before() and
time_after() that will later on both be needed by SCTP code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building the htmldocs (in verbose mode), scripts/kernel-doc reports the
following type of warnings:
Warning(include/linux/ktime.h:75): No description found for return value of
'ktime_set'
Fix them by using a "Return:" section to describe the return values.
(Also apply some minor reformatting along the way.)
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
David Howells
Kent Overstreet
Chunguang Xu
Peter Zijlstra
Linus Torvalds
Vincenzo Frascino
Arnd Bergmann
Eric Dumazet
Thomas Gleixner
Vegard Nossum
John Stultz
Nicolas Pitre
Chunyan Zhang
Daniel Borkmann
Yacine Belkadi