Commit e13647c1 (phylib: Add support for the LXT973 phy.) added a new ID
but neglected to also add it to the MODULE_DEVICE_TABLE.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pci_enable_msix() returned ret<0, entries and vxge_entries were leaked.
While at it, use the centralized exit idiom in the function.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAPI applications can handle several connections in parallel,
so one connection state per application isn't sufficient.
Store the connection state in the channel structure instead.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt to buggy device firmware which accepts setting HLC only in the
same command line as BC, by encoding HLC and BC in a single command
if both are specified, and rejecting HLC without BC.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Gigaset CAPI driver handled all DATA_B3_REQ messages as if the
Delivery Confirmation flag bit was set, delaying the emission of the
DATA_B3_CONF reply until the data was actually transmitted. Some
CAPI applications (notably Asterisk) aren't happy with that
behaviour. Change it to actually evaluate the Delivery Confirmation
flag as described the CAPI specification.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the Gigaset CAPI driver select L2_VOICE (AT^SBPR=2) as the
layer 2 encoding for transparent connections, like the ISDN4Linux
variant. L2_BITSYNC (AT^SBPR=0) mutes internal connections and
distorts external ones.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the Gigaset CAPI driver to limit the length of a connection's
payload data receive buffers to the corresponding CAPI application's
data buffer size, as some real-life CAPI applications tend to be
rather unhappy if they receive bigger data blocks than requested.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the call to phy_connect fails, we will return directly instead of freeing
the previously allocated struct net_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
smc91c92_cs:
Fix the problem that lan & modem does not work simultaneously
in the Megahertz multi-function card.
We need to write MEGAHERTZ_ISR to retrigger interrupt.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of TLLAO option created a kernel OOPS regression
for the case where neighbor advertisement is being sent via
proxy path. When using proxy, ipv6_get_ifaddr() returns NULL
causing the NULL dereference.
Change causing the bug was:
commit f7734fdf61
Author: Octavian Purdila <opurdila@ixiacom.com>
Date: Fri Oct 2 11:39:15 2009 +0000
make TLLAO option for NA packets configurable
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building tx command, always set TX_CMD_FLAG_PROT_REQUIRE_MSK
for 5000 series and up.
Without setting this bit the firmware will not examine the RTS/CTS setting
and thus not send traffic with the appropriate protection. RTS/CTS is is
required for HT traffic in a noisy environment where, without this setting,
connections will stall on some hardware as documented in the patch that
initially attempted to address this:
commit 1152dcc28c
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date: Fri Jan 15 13:42:58 2010 -0800
iwlwifi: Fix throughput stall issue in HT mode for 5000
Similar to 6000 and 1000 series, RTS/CTS is the recommended
protection mechanism for 5000 series in HT mode based on the HW design.
Using RTS/CTS will better protect the inner exchange from interference,
especially in highly-congested environment, it also prevent uCode encounter
TX FIFO underrun and other HT mode related performance issues.
For 3945 and 4965, different flags are used for RTS/CTS or CTS-to-Self
protection.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
commit 3474ad635d
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Apr 29 04:43:05 2010 -0700
iwlwifi: apply filter flags directly
broke multicast. The reason, it turns out, is that
the code previously checked if ALLMULTI _changed_,
which the new code no longer did, and normally it
_never_ changes. Had somebody changed it manually,
the code prior to my patch there would have been
broken already.
The reason is that we always, unconditionally, ask
the device to pass up all multicast frames, but the
new code made it depend on ALLMULTI which broke it
since now we'd pass up multicast frames depending
on the default filter in the device, which isn't
necessarily what we want (since we don't program it
right now).
Fix this by simply not checking allmulti as we have
allmulti behaviour enabled already anyway.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the bundle validation code to not assume having a valid policy.
When we have multiple transformations for a xfrm policy, the bundle
instance will be a chain of bundles with only the first one having
the policy reference. When policy_genid is bumped it will expire the
first bundle in the chain which is equivalent of expiring the whole
chain.
Reported-bisected-and-tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where ANI is started without checking
if it is right to start. This might lead to a case where ani
timer would be left undeleted and cause improper memory acccess
during module unload. This bug is clearly exposed with
paprd support where the driver detects tx hang and does a
chip reset. During this reset ani is (re)started without checking
if it needs to be started. This would leave a timer scheduled
even after all the resources are freed and cause a panic.
This patch introduces a bit in sc_flags to indicate if ani
needs to be started in sw_scan_start() and ath_reset().
This would fix the following panic. This issue is easily seen
with ar9003 + paprd.
BUG: unable to handle kernel paging request at 0000000000003f38
[<ffffffff81075391>] ? __queue_work+0x41/0x50
[<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370
[<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110
[<ffffffff81061f69>] __do_softirq+0xb9/0x1f0
[<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160
[<ffffffff8100af5c>] call_softirq+0x1c/0x30
[<ffffffff8100c9f5>] do_softirq+0x65/0xa0
[<ffffffff81061e25>] irq_exit+0x85/0x90
[<ffffffff8155e095>] do_IRQ+0x75/0xf0
[<ffffffff815570d3>] ret_from_intr+0x0/0x11
<EOI>
[<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119
[<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119
[<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140
[<ffffffff81008da3>] cpu_idle+0xb3/0x110
[<ffffffff81550722>] start_secondary+0x1ee/0x1f5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable statistics initialization for eth clients that do not support
statistics. This prevents memory corruption on bnx2x hw.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
commit aa2ea0586d (tcp: fix outsegs stat for TSO segments) incorrectly
assumed SNMP_ADD_STATS() was used from BH context.
Fix this using mib[!in_softirq()] instead of mib[0]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the setting of the low_latency flag.
tty_flip_buffer_push() is occasionally being called in irq context, which
causes a hang if the low_latency flag is set.
Removing the low_latency flag only seems to impact the flush to ldisc,
which will now be put on a workqueue.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that the new UFO software fallback path
fails under certain conditions with NFS. I tracked the problem
down to the generation of UFO packets that are smaller than the
MTU. The software fallback path simply discards these packets.
This patch fixes the problem by not generating such packets on
the UFO path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix commit 4cd24eaf0 (net: use netdev_mc_count and netdev_mc_empty when
appropriate)
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
$ make CONFIG_DEBUG_SECTION_MISMATCH=y
[...]
WARNING: drivers/net/built-in.o(.data+0x0): Section mismatch in reference from the variable mipsnet_driver to the function .init.text:mipsnet_probe()
The variable mipsnet_driver references
the function __init mipsnet_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
[...]
Fixed by making mipsnet_probe __devinit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/mipsnet.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse
Jiri Slaby
Michal Schmidt
Tilman Schmidt
Florian Fainelli
Ken Kawasaki
stephen hemminger
Wey-Yi Guy
Johannes Berg
Gustavo F. Padovan
Timo Teräs
Brandon Philips
Vasanthakumar Thiagarajan
Dmitry Kravkov
Anirban Chakraborty
Eric Dumazet
David S. Miller
Filip Aben
Herbert Xu
Helge Deller
Ralf Baechle