Add support for the KSZ87xx low-loss cable PHY tunables in the Micrel
PHY driver by implementing get_tunable and set_tunable callbacks.
These callbacks expose vendor-specific PHY tunables used to control the
KSZ87xx embedded PHY receiver behavior when operating with short or
low-loss Ethernet cables. The tunables provide:
- a boolean short-cable preset applying known good settings;
- an integer LPF bandwidth control;
- an integer DSP EQ initial value control.
The Micrel PHY driver forwards these tunables via standard phy_read() /
phy_write() operations, which are virtualized by the KSZ8 DSA driver and
translated into the appropriate indirect switch register accesses.
Reviewed-by: Marek Vasut <marex@nabladev.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Signed-off-by: Fidelio Lawson <fidelio.lawson@exotec.com>
Link: https://patch.msgid.link/20260609-ksz87xx_errata_low_loss_connections-v10-3-9ba4418cf3db@exotec.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN8814 QSGMII soft reset was moved into the probe function to avoid
triggering it for each of 4 PHY-s in the package.
However, that broke QSGMII link between the MAC and PHY on most LAN8814
PHY-s, specificaly for us on the Microchip LAN969x switch.
Reading the QSGMII status registers it was visible that lanes were only
partially synced.
It looks like the reset timing is crucial, so lets move the reset back
into the .config_init function but guard it with phy_package_init_once()
to avoid it being triggered on each of 4 PHY-s in the package.
Change the probe function to use phy_package_probe_once() for coma and PtP
setup.
Fixes: 96a9178a29 ("net: phy: micrel: lan8814 fix reset of the QSGMII interface")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://patch.msgid.link/20260428134138.1741253-1-robert.marko@sartura.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Since the commit 25c6a5ab15 ("net: phy: micrel: Dynamically control
external clock of KSZ PHY"), the clock of Micrel PHY has been enabled
by phy_driver::resume() and disabled by phy_driver::suspend(). However,
devm_clk_get_optional_enabled() is used in kszphy_probe(), so the clock
will automatically be disabled when the device is unbound from the bus.
Therefore, this could cause the clock to be disabled twice, resulting
in clk driver warnings.
For example, this issue can be reproduced on i.MX6ULL platform, and we
can see the following logs when removing the FEC MAC drivers.
$ echo 2188000.ethernet > /sys/bus/platform/drivers/fec/unbind
$ echo 20b4000.ethernet > /sys/bus/platform/drivers/fec/unbind
[ 109.758207] ------------[ cut here ]------------
[ 109.758240] WARNING: drivers/clk/clk.c:1188 at clk_core_disable+0xb4/0xd0, CPU#0: sh/639
[ 109.771011] enet2_ref already disabled
[ 109.793359] Call trace:
[ 109.822006] clk_core_disable from clk_disable+0x28/0x34
[ 109.827340] clk_disable from clk_disable_unprepare+0xc/0x18
[ 109.833029] clk_disable_unprepare from devm_clk_release+0x1c/0x28
[ 109.839241] devm_clk_release from devres_release_all+0x98/0x100
[ 109.845278] devres_release_all from device_unbind_cleanup+0xc/0x70
[ 109.851571] device_unbind_cleanup from device_release_driver_internal+0x1a4/0x1f4
[ 109.859170] device_release_driver_internal from bus_remove_device+0xbc/0xe4
[ 109.866243] bus_remove_device from device_del+0x140/0x458
[ 109.871757] device_del from phy_mdio_device_remove+0xc/0x24
[ 109.877452] phy_mdio_device_remove from mdiobus_unregister+0x40/0xac
[ 109.883918] mdiobus_unregister from fec_enet_mii_remove+0x40/0x78
[ 109.890125] fec_enet_mii_remove from fec_drv_remove+0x4c/0x158
[ 109.896076] fec_drv_remove from device_release_driver_internal+0x17c/0x1f4
[ 109.962748] WARNING: drivers/clk/clk.c:1047 at clk_core_unprepare+0xfc/0x13c, CPU#0: sh/639
[ 109.975805] enet2_ref already unprepared
[ 110.002866] Call trace:
[ 110.031758] clk_core_unprepare from clk_unprepare+0x24/0x2c
[ 110.037440] clk_unprepare from devm_clk_release+0x1c/0x28
[ 110.042957] devm_clk_release from devres_release_all+0x98/0x100
[ 110.048989] devres_release_all from device_unbind_cleanup+0xc/0x70
[ 110.055280] device_unbind_cleanup from device_release_driver_internal+0x1a4/0x1f4
[ 110.062877] device_release_driver_internal from bus_remove_device+0xbc/0xe4
[ 110.069950] bus_remove_device from device_del+0x140/0x458
[ 110.075469] device_del from phy_mdio_device_remove+0xc/0x24
[ 110.081165] phy_mdio_device_remove from mdiobus_unregister+0x40/0xac
[ 110.087632] mdiobus_unregister from fec_enet_mii_remove+0x40/0x78
[ 110.093836] fec_enet_mii_remove from fec_drv_remove+0x4c/0x158
[ 110.099782] fec_drv_remove from device_release_driver_internal+0x17c/0x1f4
After analyzing the process of removing the FEC driver, as shown below,
it can be seen that the clock was disabled twice by the PHY driver.
fec_drv_remove()
--> fec_enet_close()
--> phy_stop()
--> phy_suspend()
--> kszphy_suspend() #1 The clock is disabled
--> fec_enet_mii_remove()
--> mdiobus_unregister()
--> phy_mdio_device_remove()
--> device_del()
--> devm_clk_release() #2 The clock is disabled again
Therefore, devm_clk_get_optional() is used to fix the above issue. And
to avoid the issue mentioned by the commit 9853294627 ("net: phy:
micrel: use devm_clk_get_optional_enabled for the rmii-ref clock"), the
clock is enabled by clk_prepare_enable() to get the correct clock rate.
Fixes: 25c6a5ab15 ("net: phy: micrel: Dynamically control external clock of KSZ PHY")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260126081544.983517-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.18-rc6).
No conflicts, adjacent changes in:
drivers/net/phy/micrel.c
96a9178a29 ("net: phy: micrel: lan8814 fix reset of the QSGMII interface")
61b7ade9ba ("net: phy: micrel: Add support for non PTP SKUs for lan8814")
and a trivial one in tools/testing/selftests/drivers/net/Makefile.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.18-rc5).
Conflicts:
drivers/net/wireless/ath/ath12k/mac.c
9222582ec5 ("Revert "wifi: ath12k: Fix missing station power save configuration"")
6917e268c4 ("wifi: ath12k: Defer vdev bring-up until CSA finalize to avoid stale beacon")
https://lore.kernel.org/11cece9f7e36c12efd732baa5718239b1bf8c950.camel@sipsolutions.net
Adjacent changes:
drivers/net/ethernet/intel/Kconfig
b1d16f7c00 ("libie: depend on DEBUG_FS when building LIBIE_FWLOG")
93f53db9f9 ("ice: switch to Page Pool")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the get_mse_capability() and get_mse_snapshot() PHY driver ops
for KSZ9477-series integrated PHYs to demonstrate the new PHY MSE
UAPI.
These PHYs do not expose a documented direct MSE register, but the
Signal Quality Indicator (SQI) registers are derived from the
internal MSE computation. This hook maps SQI readings into the MSE
interface so that tooling can retrieve the raw value together with
metadata for correct interpretation in userspace.
Behaviour:
- For 1000BASE-T, report per-channel (A–D) values and support a
WORST channel selector.
- For 100BASE-TX, only LINK-wide measurements are available.
- Report average MSE only, with a max scale based on
KSZ9477_MMD_SQI_MASK and a fixed refresh rate of 2 µs.
This mapping differs from the OPEN Alliance SQI definition, which
assigns thresholds such as pre-fail indices; the MSE interface
instead provides the raw measurement, leaving interpretation to
userspace.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20251027122801.982364-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, during the LAN8814 PTP probe shared->phydev is only set if PTP
clock gets actually set, otherwise the function will return before setting
it.
This is an issue as shared->phydev is unconditionally being used when IRQ
is being handled, especially in lan8814_gpio_process_cap and since it was
not set it will cause a NULL pointer exception and crash the kernel.
So, simply always set shared->phydev to avoid the NULL pointer exception.
Fixes: b3f1a08fcf ("net: phy: micrel: Add support for PTP_PF_EXTTS for lan8814")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20251021132034.983936-1-robert.marko@sartura.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ksz9477_phy_errata function currently assigns the return value of
genphy_restart_aneg() to a variable and then immediately returns it
err = genphy_restart_aneg(phydev);
if (err)
return err;
return err;
This can be simplified by directly returning the function call
result, as the intermediate variable and conditional are redundant.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251017193525.1457064-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit introduced the function lanphy_modify_page_reg which
as name suggests it, it modifies the registers. In the same commit we
have started to use this function inside the drivers. The problem is
that in the function lan8814_config_init we passed the wrong page number
when disabling the aneg towards host side. We passed extended page number
4(LAN8814_PAGE_COMMON_REGS) instead of extended page
5(LAN8814_PAGE_PORT_REGS)
Fixes: a0de636ed7 ("net: phy: micrel: Introduce lanphy_modify_page_reg")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250925064702.3906950-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fidelio Lawson
Robert Marko
Jens Emil Schulz Østergaard
Linus Torvalds
Kees Cook
Jakub Kicinski
Wei Fang
Stefan Eichenberger
Vadim Fedorenko
Horatiu Vultur
Oleksij Rempel
Alok Tiwari