The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231201133747.1099286-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Observed on dmesg of my laptop I see the following
output:
[ 19.898700] psmouse serio1: synaptics: queried max coordinates: x [..5678], y [..4694]
[ 19.936057] psmouse serio1: synaptics: queried min coordinates: x [1266..], y [1162..]
[ 19.936076] psmouse serio1: synaptics: Your touchpad (PNP: LEN0411 PNP0f13) says it can support a different bus. If i2c-hid and hid-rmi are not used, you might want to try setting psmouse.synaptics_intertouch to 1 and report this to linux-input@vger.kernel.org.
[ 20.008901] psmouse serio1: synaptics: Touchpad model: 1, fw: 10.32, id: 0x1e2a1, caps: 0xf014a3/0x940300/0x12e800/0x500000, board id: 3471, fw id: 2909640
[ 20.008925] psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0
[ 20.053344] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[ 20.397608] mousedev: PS/2 mouse device common for all mice
This patch will add its pnp id to the smbus list to
produce the setup of intertouch for the device.
Signed-off-by: José Pekkarinen <jose.pekkarinen@foxhound.fi>
Link: https://lore.kernel.org/r/20231114063607.71772-1-jose.pekkarinen@foxhound.fi
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Touch controllers need some time after receiving reset command for the
firmware to finish re-initializing and be ready to respond to commands
from the host. The driver already had handling for the post-reset delay
for I2C and SPI transports, this change adds the handling to
SMBus-connected devices.
SMBus devices are peculiar because they implement legacy PS/2
compatibility mode, so reset is actually issued by psmouse driver on the
associated serio port, after which the control is passed to the RMI4
driver with SMBus companion device.
Note that originally the delay was added to psmouse driver in
92e24e0e57 ("Input: psmouse - add delay when deactivating for SMBus
mode"), but that resulted in an unwanted delay in "fast" reconnect
handler for the serio port, so it was decided to revert the patch and
have the delay being handled in the RMI4 driver, similar to the other
transports.
Tested-by: Jeffery Miller <jefferymiller@google.com>
Link: https://lore.kernel.org/r/ZR1yUFJ8a9Zt606N@penguin
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the SMBus connection is attempted psmouse_smbus_init() sets
the fast_reconnect pointer to psmouse_smbus_reconnecti(). If SMBus
initialization fails, elantech_setup_ps2() and synaptics_init_ps2() will
fallback to PS/2 mode, replacing the psmouse private data. This can cause
issues on resume, since psmouse_smbus_reconnect() expects to find an
instance of struct psmouse_smbus_dev in psmouse->private.
The issue was uncovered when in 92e24e0e57 ("Input: psmouse - add
delay when deactivating for SMBus mode") psmouse_smbus_reconnect()
started attempting to use more of the data structure. The commit was
since reverted, not because it was at fault, but because there was found
a better way of doing what it was attempting to do.
Fix the problem by resetting the fast_reconnect pointer in psmouse
structure in elantech_setup_ps2() and synaptics_init_ps2() when the PS/2
mode is used.
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Tested-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Jeffery Miller <jefferymiller@google.com>
Fixes: bf232e460a ("Input: psmouse-smbus - allow to control psmouse_deactivate")
Link: https://lore.kernel.org/r/20231005002249.554877-1-jefferymiller@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 92e24e0e57.
While the patch itself is correct, it uncovered an issue with fallback
to PS/2 mode, where we were leaving psmouse->fast_reconnect handler set
to psmouse_smbus_reconnect(), which caused crashes.
While discussing various approaches to fix the issue it was noted that
this patch ass undesired delay in the "fast" resume path of PS/2 device,
and it would be better to actually use "reset_delay" option defined in
struct rmi_device_platform_data and have RMI code handle it for SMBus
transport as well. So this patch is being reverted to deal with crashes
and a better solution will be merged shortly.
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Closes: https://lore.kernel.org/all/ca0109fa-c64b-43c1-a651-75b294d750a1@leemhuis.info/
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230920125829.1478827-29-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is a period of time between the psmouse deactivate and the
ability to communicate with the SMBus companion. Insert a
sleep after the deactivate to account for the delay and ensure
the SMBus companion is responsive.
Attempting to read from the SMBus companion too quickly was causing
the touchpad on machines with an i801_smbus companion to stop working
after a sleep/resume cycle.
On resume the rmi4_smbus would fail with errors reading the SMBus version
number:
```
[5454] i2c_i801:i801_check_post:414: i801_smbus 0000:00:1f.3: No response
smbus_result: i2c-0 a=02c f=0000 c=fd BYTE_DATA rd res=-6
rmi4_smbus 0-002c: failed to get SMBus version number!
...
rmi4_f01 rmi4-00.fn01: Failed to restore normal operation: -6.
rmi4_f01 rmi4-00.fn01: Resume failed with code -6.
rmi4_physical rmi4-00: Failed to suspend functions: -6
rmi4_smbus 0-002c: Failed to resume device: -6
```
In this case the rmi_smb_get_version fails with -ENXIO if it happens too
soon after the preceding serio_resume -> psmouse_deactivate call.
On boot this issue could cause the touchpad to stay in the limited PS/2
mode. This only reproduced in 1 in 10 boots on the Lenovo T440p.
Failures in the log on boot would show up as:
```
psmouse serio1: synaptics: Trying to set up SMBus access
[122] i2c_i801:i801_check_post:437: i801_smbus 0000:00:1f.3: No response
psmouse serio1: synaptics: SMbus companion is not ready yet
```
Experimentation on the Lenovo T440p showed that a delay of 7-12ms on
resume allowed the companion to respond.
The 30ms delay in this patch was chosen based on the linux-input message:
Link: https://lore.kernel.org/all/BYAPR03MB47572F2C65E52ED673238D41B2439@BYAPR03MB4757.namprd03.prod.outlook.com/
Signed-off-by: Jeffery Miller <jefferymiller@google.com>
Link: https://lore.kernel.org/r/20230726025256.81174-1-jefferymiller@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of exposing inner workings of libps2 to drivers such as atkbd and
psmouse, have them define pre-receive and receive callbacks, and provide a
common handler that can be used with underlying serio port.
While at this add kerneldoc to the module.
Link: https://lore.kernel.org/r/ZGK81cxqjr/KS1kA@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The AlpsPS/2 code previously relied on the assumption that `char` is a
signed type, which was true on x86 platforms (the only place where this
driver is used) before kernel 6.2. However, on 6.2 and later, this
assumption is broken due to the introduction of -funsigned-char as a new
global compiler flag.
Fix this by explicitly specifying the signedness of `char` when sign
extending the values received from the device.
Fixes: f3f33c6776 ("Input: alps - Rushmore and v7 resolution support")
Signed-off-by: msizanoen <msizanoen@qtmlabs.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230320045228.182259-1-msizanoen@qtmlabs.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- a set of tweaks to iqs269a touch controller driver
- a fix for ads7846 driver to properly handle 7845 chip
- cap11xx driver will support cap1203, cap1293 and cap1298 models
- xpad driver will support 8BitDo Pro 2 Wired Controller
- input drivers have been switched to DEFINE_SIMPLE_DEV_PM_OPS() and
pm_sleep_ptr()
- other miscellaneous fixes and tweaks
* tag 'input-for-v6.3-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (113 commits)
dt-bindings: input: iqs626a: Redefine trackpad property types
Input: iqs626a - drop unused device node references
dt-bindings: input: touchscreen: st,stmfts: convert to dtschema
Input: cyttsp5 - fix bitmask for touch buttons
Input: exc3000 - properly stop timer on shutdown
Input: synaptics-rmi4 - fix SPI device ID
Input: cap11xx - add support for cap1203, cap1293 and cap1298
dt-bindings: input: microchip,cap11xx: add cap1203, cap1293 and cap1298
Input: pmic8xxx-keypad - fix a Kconfig spelling mistake & hyphenation
Input: edt-ft5x06 - fix typo in a comment
Input: tegra-kbc - use devm_platform_get_and_ioremap_resource()
Input: st-keyscan - use devm_platform_get_and_ioremap_resource()
Input: spear-keyboard - use devm_platform_get_and_ioremap_resource()
Input: olpc_apsp - use devm_platform_get_and_ioremap_resource()
Input: arc_ps2 - use devm_platform_get_and_ioremap_resource()
Input: apbps2 - use devm_platform_get_and_ioremap_resource()
Input: altera_ps2 - use devm_platform_get_and_ioremap_resource()
Input: ads7846 - don't check penirq immediately for 7845
Input: ads7846 - always set last command to PWRDOWN
Input: ads7846 - don't report pressure for ads7845
...
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
Pull input fixes from Dmitry Torokhov:
- touchpads on HP 15-* laptops switched back to PS/2 emulation mode
- a quirk for Clevo PCX0DX/TUXEDO XP1511 to make sure keyboard is
responding after resume
* tag 'input-for-v6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Clevo PCX0DX to i8042 quirk table
Revert "Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode"
Linus Walleij
ye xingchen
Uwe Kleine-König
José Pekkarinen
Dmitry Torokhov
Jeffery Miller
Krzysztof Kozlowski
msizanoen
Jason A. Donenfeld
Linus Torvalds
Arnd Bergmann