PTN5150 is able to detect CC polarity. The field[1:0] of CC status
register (04H) will keep the result.
00: Cable Not Attached
01: CC1 is connected (normal orientation)
10: CC2 is connected (reversed orientation)
11: Reserved
Add orientation switch support to correctly set orientation of
multiplexer according to CC status.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/lkml/20250926025309.24267-2-xu.yang_2@nxp.com/
Make EXTCON_MAX14526 depend on I2C to address a kconfig warning and
subsequent build errors:
WARNING: unmet direct dependencies detected for REGMAP_I2C
Depends on [m]: I2C [=m]
Selected by [y]:
- EXTCON_MAX14526 [=y] && EXTCON [=y]
ld: vmlinux.o: in function `max14526_driver_init':
extcon-max14526.c:(.init.text+0x77b0e): undefined reference to `i2c_register_driver'
ld: vmlinux.o: in function `max14526_driver_exit':
extcon-max14526.c:(.exit.text+0x467c): undefined reference to `i2c_del_driver'
Fixes: 145af3ddd1 ("extcon: Add basic support for Maxim MAX14526 MUIC")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/lkml/20250515234803.1385375-1-rdunlap@infradead.org/
The MAX14526 is designed to simplify interface requirements on portable
devices by multiplexing common inputs (USB, UART, Microphone, Stereo Audio
and Composite Video) on a single micro/mini USB connector. The USB input
supports Hi-Speed USB and the audio/video inputs feature negative rail
signal operation allowing simple DC coupled accessories. These device allow
a single micro/mini USB port to support all the common interfaces on
Cellular phones and portable media players over the same external lines.
Link: https://lore.kernel.org/lkml/20250506073216.43059-3-clamor95@gmail.com/
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add a new driver for the ON Semiconductor LC824206XA microUSB switch and
accessory detector chip.
ON Semiconductor has an "Advance Information" datasheet available
(ENA2222-D.PDF), but no full datasheet. So there is no documentation
available for the registers.
This driver is based on the register info from the extcon-fsa9285.c driver,
from the Lollipop Android sources for the Lenovo Yoga Tablet 2 (Pro)
830 / 1050 / 1380 models. Note despite the name this is actually a driver
for the LC824206XA not the FSA9285.
This has only been tested on a Lenovo Yoga Tablet 2 Pro 1380 and
using the driver on other setups may require additional work.
So far this driver is only used on x86/ACPI (non devicetree) devs.
Therefor there is no devicetree bindings documentation for this driver's
"onnn,enable-miclr-for-dcp" property since this is not used in actual
devicetree files and the dt bindings maintainers have requested properties
with no actual dt users to _not_ be added to the dt bindings.
Link: https://lore.kernel.org/lkml/20240512204019.58121-1-hdegoede@redhat.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
IRQ_DOMAIN is a hidden (not user visible) symbol. Users cannot set
it directly thru "make *config", so drivers should select it instead
of depending on it if they need it.
Relying on it being set for a dependency is risky.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change EXTCON_MAX8997's use of "depends on" for
IRQ_DOMAIN to "select".
Link: https://lore.kernel.org/lkml/20240213060028.9744-1-rdunlap@infradead.org/
Fixes: dca1a71e41 ("extcon: Add support irq domain for MAX8997 muic")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The driver fails to link when CONFIG_POWER_SUPPLY is disabled:
x86_64-linux-ld: vmlinux.o: in function `cht_wc_extcon_psy_get_prop':
extcon-intel-cht-wc.c:(.text+0x15ccda7): undefined reference to `power_supply_get_drvdata'
x86_64-linux-ld: vmlinux.o: in function `cht_wc_extcon_pwrsrc_event':
extcon-intel-cht-wc.c:(.text+0x15cd3e9): undefined reference to `power_supply_changed'
x86_64-linux-ld: vmlinux.o: in function `cht_wc_extcon_probe':
extcon-intel-cht-wc.c:(.text+0x15cd596): undefined reference to `devm_power_supply_register'
It should be possible to change the driver to not require this at
compile time and still provide other functions, but adding a hard
Kconfig dependency does not seem to have any practical downsides
and is simpler since the option is normally enabled anyway.
Fixes: 66e31186cd ("extcon: intel-cht-wc: Add support for registering a power_supply class-device")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
When CONFIG_USB_ROLE_SWITCH=m, tusb320 cannot be built-in:
ld.lld: error: undefined symbol: fwnode_usb_role_switch_get
>>> referenced by extcon-usbc-tusb320.c
>>> drivers/extcon/extcon-usbc-tusb320.o:(tusb320_probe) in archive vmlinux.a
ld.lld: error: undefined symbol: usb_role_switch_set_role
>>> referenced by extcon-usbc-tusb320.c
>>> drivers/extcon/extcon-usbc-tusb320.o:(tusb320_state_update_handler) in archive vmlinux.a
Add the appropriate Kconfig dependency to prevent this
configuration but still allow the driver to be built-in
when USB_ROLE_SWITCH is disabled.
Fixes: df101446a4 ("extcon: usbc-tusb320: add usb_role_switch support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem,
which can expose details collected by the TUSB320 in a far more
precise way than extcon. Since there are existing users in the
kernel and in DT which depend on the extcon interface, keep it
for now.
Add TYPE-C interface and expose the supported supply current,
direction and connector polarity via the TYPE-C interface.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Some usb controller drivers may not support extcon but use
usb role class as it's the preferred approach, so to support
usb dual role switch with usb role class, add usb role class
consumer support.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
SM5703 is another MFD from Silicon Mitus which has a very similar MUIC
unit to the one in SM5502. The only difference I've noticed is slightly different
configuration only enables the interrupts which are exactly the same as on SM5502.
If we make use of different interrupts in the future, this can be improved by having
a separate struct for SM5703, but the main functionality (detecting cable or OTG adapter)
is working properly.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
So far the extcon-intel-cht-wc code has only been tested on devices with
a Type-C connector with USB-PD, USB3 (superspeed) and DP-altmode support
through a FUSB302 Type-C controller.
Some devices with the intel-cht-wc PMIC however come with an USB-micro-B
connector, or an USB-2 only Type-C connector without USB-PD.
Which device-model we are running on can be identified with the new
cht_wc_model intel_soc_pmic field. On models without a Type-C controller
the extcon code must control the Vbus 5V boost converter and the USB role
switch depending on the detected cable-type.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
use low level P-Unit semaphore lock for axp288 register
accesses directly and for more than one access a time,
to reduce the number of times this semaphore is locked
and released which is an expensive operation.
i2c-bus to the XPower is shared between the kernel and the
SoCs P-Unit. The P-Unit has a semaphore wich the kernel must
lock for axp288 register accesses. When the P-Unit semaphore
is locked CPU and GPU power states cannot change or the system
will freeze.
The P-Unit semaphore lock is already managed inside the regmap
access logic, but for each access the semaphore is locked and
released. So use directly iosf_mbi_(un)block_punit_i2c_access(),
we are safe in doing so because nested calls to the same
semaphore are turned to nops.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
SM5504 is another MUIC from Silicon Mitus that is fairly similar
to SM5502. They seem to use the same register set, but:
- SM5504 has some additional bits in SM5502_REG_CONTROL
- SM5504 has a quite different set of interrupts
- SM5504 reports USB OTG as dev_type1 = BIT(0) instead of BIT(7)
Overall it's minor and we can support this by defining a separate
struct sm5502_type for SM5504.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The jack handling for arizona codecs is being refactored so that it is
done directly by the codec drivers, instead of having an extcon-driver
bind to a separate "arizona-extcon" child-device for this.
drivers/mfd/arizona-core.c has already been updated to no longer
instantiate an "arizona-extcon" child-device for the arizona codecs.
This means that the "arizona-extcon" driver is no longer useful
(there are no longer any devices for it to bind to).
This commit drops the extcon Kconfig / Makefile bits and moves
drivers/extcon/extcon-arizona.c to sound/soc/codecs/arizona-jack.c .
This is a preparation patch for converting the arizona extcon-driver into
a helper library for letting the arizona codec-drivers directly report jack
state through the standard sound/soc/soc-jack.c functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds an extcon driver for the TI TUSB320 USB Type-C device.
This can be used to detect whether the port is configured as a
downstream or upstream facing port.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Fix Kconfig dependency warning and subsequent build errors caused by
the Kconfig entry for EXTCON-FSA9480. It should not select
REGMAP_I2C unless I2C is already set/enabled.
WARNING: unmet direct dependencies detected for REGMAP_I2C
Depends on [n]: I2C [=n]
Selected by [y]:
- EXTCON_FSA9480 [=y] && EXTCON [=y] && INPUT [=y]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[cw00.choi: adjust the patch title and remove the long warning messages]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Hans de Goede pointed, using this driver without ACPI
makes little sense, so add ACPI dependency to Kconfig entry
to fix a build error while CONFIG_ACPI is not set.
drivers/extcon/extcon-axp288.c: In function 'axp288_extcon_probe':
drivers/extcon/extcon-axp288.c:363:20: error: dereferencing pointer to incomplete type
put_device(&adev->dev);
Fixes: 0cf064db94 ("extcon: axp288: Convert to use acpi_dev_get_first_match_dev()")
Reported-by: Hulk Robot <hulkci@huawei.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On Intel Merrifield the Basin Cove PMIC provides a feature to detect
the USB connection type. This driver utilizes the feature in order
to support the USB dual role detection.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The PTN5150 dependencies look like they were meant to do the
right thing, but they actually should not allow building without
I2C for compile testing, as that results in a Kconfig warning
and subsequent build failure:
WARNING: unmet direct dependencies detected for REGMAP_I2C
Depends on [m]: I2C [=m]
Selected by [y]:
- EXTCON_PTN5150 [=y] && EXTCON [=y] && (I2C [=m] && GPIOLIB [=y] || COMPILE_TEST [=y])
Selected by [m]:
- EEPROM_AT24 [=m] && I2C [=m] && SYSFS [=y]
- KEYBOARD_CAP11XX [=m] && !UML && INPUT [=y] && INPUT_KEYBOARD [=y] && OF [=y] && I2C [=m]
- INPUT_DRV260X_HAPTICS [=m] && !UML && INPUT_MISC [=y] && INPUT [=y] && I2C [=m] && (GPIOLIB [=y] || COMPILE_TEST [=y])
- ... [many others]
Add parentheses around the expression so we can compile-test
without GPIOLIB but not without I2C.
Fixes: 4ed754de2d ("extcon: Add support for ptn5150 extcon driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
PTN5150 is a small thin low power CC (Configurationn Channel)
Logic chip supporting the USB Type-C connector application with
CC control logic detection and indication functions.
Signed-off-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
[cw00.choi: Fix bulid dependency and clean-up code]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The AXP288 BC1.2 charger detection / extcon code may seem like a strange
place to add code to control the USB role-switch on devices with an AXP288,
but there are 2 reasons to do this inside the axp288 extcon code:
1) On many devices the USB role is controlled by ACPI AML code, but the AML
code only switches between the host and none roles, because of Windows
not really using device mode. To make device mode work we need to toggle
between the none/device roles based on Vbus presence, and the axp288
extcon gets interrupts on Vbus insertion / removal.
2) In order for our BC1.2 charger detection to work properly the role
mux must be properly set to device mode before we do the detection.
Also note the Kconfig help-text / obsolete depends on USB_PHY which are
remnants from older never upstreamed code also controlling the mux from
the axp288 extcon code.
This commit also adds code to get notifications from the INT3496 extcon
device, which is used on some devices to notify the kernel about id-pin
changes instead of them being handled through AML code.
This fixes:
-Device mode not working on most CHT devices with an AXP288
-Host mode not working on devices with an INT3496 ACPI device
-Charger-type misdetection (always SDP) on devices with an INT3496 when the
USB role (always) gets initialized as host
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xu Yang
Randy Dunlap
Svyatoslav Ryhel
Hans de Goede
Stanley Chang
Arnd Bergmann
Marek Vasut
Li Jun
Markuss Broks
Fabio Aiuto
Stephan Gerhold
Michael Auchter
Enric Balletbo i Serra
Tomasz Figa
Thomas Gleixner
YueHaibing
Andy Shevchenko
Vijai Kumar K