If btusb_qca_send_vendor_req() gets a "short" read from a device, it
will accidentally treat that as a "real" read and populate the returned
value with some unknown and probably totally invalid data.
Fix this logic error up by calling usb_control_msg_recv() which
guarantees a "full" read happens, and then simplify the error checking
for when btusb_qca_send_vendor_req() is called.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If btmtk_usb_reg_read() gets a "short" read from a device, it will
accidentally treat that as a "real" read and populate the returned value
with some unknown and probably totally invalid data.
Fix this logic error up by calling usb_control_msg_recv() which
guarantees a "full" read happens, and then simplify the error checking
for when btmtk_usb_reg_read() is called (it's really just
btmtk_usb_id_get() that calls btmtk_usb_reg_read(), so fix up those
return sites.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If btmtk_usb_uhw_reg_read() gets a "short" read from a device, it will
accidentally treat that as a "real" read and populate the returned value
with some unknown and probably totally invalid data.
Fix this logic error up by calling usb_control_msg_recv() which
guarantees a "full" read happens, and then simplify the error checking
for when btmtk_usb_uhw_reg_read() is called.
Note, one caller of btmtk_usb_uhw_reg_read() does not check the return
value, but as we pre-initialize the return value as 0, an incorrect read
will not do anything wrong.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btintel_diagnostics() accesses tlv->val[0] without first validating
that the diagnostics VSE is long enough to contain that field, so
may cause reading data beyond the received frame.
Fix by validating the length before access.
Fixes: af395330ab ("Bluetooth: btintel: Add Intel devcoredump support")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btusb_recv_event_realtek() reads the event code at data[0] and the Realtek
subevent code at data[2] before deciding whether to consume a vendor event
as a coredump.
For example, the two-byte event ff 00 contains a complete vendor-event
header declaring zero parameters. The old classifier still reads a
nonexistent third byte and can misclassify the event as a coredump if the
adjacent byte is 0x34.
Require the HCI event header and first parameter to be present before
inspecting the Realtek subevent code. Short events continue through the
normal HCI receive path, which owns their protocol validation.
Fixes: 044014ce85 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
qca_controller_memdump() allocates qca->qca_memdump before processing
the first dump packet. For a sequence-zero packet it then disables IBS,
marks memdump collection active, and reads the advertised dump size.
If the controller reports a zero dump size, the error path frees the
local qca_memdump object and returns without clearing qca->qca_memdump
or undoing the collection state. A later memdump work item initializes
its local pointer from qca->qca_memdump and skips allocation when that
pointer is non-NULL, so it can operate on freed memory. The stale
collection and IBS-disabled flags can also leave waiters or later
transmit handling blocked behind an aborted dump.
Clear the saved pointer and memdump state before returning from the
invalid-size path, matching the cleanup used when hci_devcd_init() fails.
A static analysis checker reported the stale memdump state, and manual
source review confirmed the invalid-size failure path.
Fixes: 06d3fdfcdf ("Bluetooth: hci_qca: Add qcom devcoredump support")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rtlbt_parse_firmware() copies patch_length - 4 bytes before appending the
firmware version. A malformed firmware patch shorter than the version field
can make this subtraction underflow and turn the copy into an oversized
read and write during Bluetooth setup.
The existing patch_offset + patch_length check can also wrap on 32-bit
architectures. Validate the patch length and range without arithmetic
overflow before allocating or copying the patch.
Fixes: db33c77ddd ("Bluetooth: btrtl: Create separate module for Realtek BT driver")
Cc: stable@vger.kernel.org
Signed-off-by: Laxman Acharya Padhya <acharyalaxman8848@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In the TLV_TYPE_NVM branch of qca_tlv_check_data() the tag loop bound is
"while (idx < length - sizeof(struct tlv_type_nvm))". "length" is a signed
int from the firmware TLV header and sizeof(struct tlv_type_nvm) is a
size_t (12), so "length" is converted to size_t and any firmware-supplied
"length" < 12 makes the subtraction wrap to a huge value. The loop body
then reads a 12-byte struct tlv_type_nvm past the end of the short
vmalloc'd firmware buffer (and the EDL_TAG_ID_* handlers can write past it).
Rewrite the bound as "idx + sizeof(struct tlv_type_nvm) <= length"; both
operands are non-negative, so it no longer underflows and a "length" too
small for one record correctly skips the loop.
BUG: KASAN: vmalloc-out-of-bounds in qca_download_firmware.isra.0 (drivers/bluetooth/btqca.c:421)
Read of size 2 at addr ffffc900000e5004 by task kworker/u9:0/52
Workqueue: hci0 hci_power_on
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
qca_download_firmware.isra.0 (drivers/bluetooth/btqca.c:421 drivers/bluetooth/btqca.c:617)
qca_uart_setup (drivers/bluetooth/btqca.c:948)
qca_setup (drivers/bluetooth/hci_qca.c:2029)
hci_uart_setup (drivers/bluetooth/hci_ldisc.c:438)
hci_dev_open_sync (net/bluetooth/hci_sync.c:5227)
hci_power_on (net/bluetooth/hci_core.c:920)
process_one_work (kernel/workqueue.c:3322)
worker_thread (kernel/workqueue.c:3486)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
ret_from_fork_asm (arch/x86/entry/entry_64.S:245)
Fixes: 2e4edfa1e2 ("Bluetooth: qca: add missing firmware sanity checks")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Reported-by: Weiming Shi <bestswngs@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter, Bluetooth and batman-adv.
Current release - regressions:
- bluetooth: fix using chan->conn as indication to no remote netdev
Current release - new code bugs:
- netfilter: cap to maximum number of expectation per master on
updates
Previous releases - regressions:
- bluetooth:
- fix UAF of hci_conn_params in add_device_complete
- fix null ptr deref in hci_abort_conn()
- igmp: remove multicast group from hash table on device destruction
- batman-adv: prevent TVLV OOB check overflow
- eth: mlx5/mlx5e:
- fix off-by-one in single-FDB error rollback
- skip peer flow cleanup when LAG seq is unavailable
- fix crashes in dynamic per-channel stats and HV VHCA agent
- eth: mana: Sync page pool RX frags for CPU
Previous releases - always broken:
- netfilter:
- mark malformed IPv6 extension headers for hotdrop
- terminate table name before find_table_lock()
- ipvs: use parsed transport offset in TCP state lookup
- sched: act_pedit: fix TOCTOU heap OOB write in tc offload
- ethtool: rss: fix hfunc and input_xfrm parsing on big endian
- ipv4/ipv6: fix UAF and memory leak in IGMP/MLD
- tls: consume empty data records in tls_sw_read_sock()
- eth:
- octeontx2-af: fix VF bringup affecting PF promiscuous state
- gue: validate REMCSUM private option length"
* tag 'net-7.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
macsec: don't read an unset MAC header in macsec_encrypt()
dibs: loopback: validate offset and size in move_data()
octeontx2-af: fix VF bringup affecting PF promiscuous state
ethtool: rss: Fix hfunc and input_xfrm parsing on big endian
net/mlx5: Fix L3 tunnel entropy refcount leak
net: macb: drop in-flight Tx SKBs on close
net: mana: Sync page pool RX frags for CPU
net: mana: Validate the packet length reported by the NIC
selftests/net: fix EVP_MD_CTX leak in tcp_mmap
ipvs: ensure inner headers in ICMP errors are in headroom
ipvs: use parsed transport offset in SCTP state lookup
ipvs: use parsed transport offset in TCP state lookup
ipvs: pass parsed transport offset to state handlers
netfilter: handle unreadable frags
netfilter: flowtable: support IPIP tunnel with direct xmit
netfilter: flowtable: IPIP tunnel hardware offload is not yet support
netfilter: flowtable: use dst in this direction when pushing IPIP header
netfilter: ipset: allocate the proper memory for the generic hash structure
netfilter: ipset: cleanup the add/del backlog when resize failed
netfilter: ipset: exclude gc when resize is in progress
...
bpa10x_setup() sends the vendor command 0xfc0e and passes the response
to bt_dev_info() and hci_set_fw_info() as a "%s" string starting at
skb->data + 1, without checking the length:
bt_dev_info(hdev, "%s", (char *)(skb->data + 1));
hci_set_fw_info(hdev, "%s", skb->data + 1);
A device that returns a one-byte response (status only) leaves
skb->data + 1 past the end of the data, and the %s walk reads adjacent
slab memory until it meets a NUL. The same happens when the payload is
not NUL-terminated within skb->len. The out-of-bounds bytes end up in
the kernel log and the firmware-info debugfs file.
Print the revision string with a bounded "%.*s" limited to skb->len - 1
instead. This keeps the string readable for well-behaved devices while
never reading past the received data, and does not fail setup, so a
device returning a short or unterminated response keeps working.
Fixes: ddd68ec8f4 ("Bluetooth: bpa10x: Read revision information in setup stage")
Reported-by: Xiang Mei <xmei5@asu.edu>
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The FLR branch in btintel_pcie_reset_work() open-coded the entire
re-init sequence: btintel_pcie_release_hdev() (hci_unregister_dev +
hci_free_dev), pci_try_reset_function(), enable_interrupts /
config_msix / enable_bt / reset_ia / start_rx, then
btintel_pcie_setup_hdev() (hci_alloc_dev_priv + hci_register_dev).
Every probe() init step had to be kept in sync with this second
copy in the reset path, and any failure mid-sequence left state to
unwind by hand.
The PLDR path already delegates teardown and re-init to the PCI
core via device_reprobe(): .remove() destroys data through devres
and unregisters hdev, then .probe() rebuilds everything from
scratch. Apply the same model to FLR.
Introduce btintel_pcie_perform_flr() mirroring perform_pldr(). It
runs pci_try_reset_function() (required to avoid the device_lock
ABBA against btintel_pcie_remove(), which calls
disable_work_sync(&reset_work) while holding device_lock) followed
by device_reprobe(). On success, data is destroyed and a fresh
probe re-INIT_WORKs coredump_work with disable count 0, so
enable_work() must not be called; on failure, data is still alive
and the caller balances the earlier disable_work_sync(). The
contract is documented on the helper and reiterated at the
reset_work() call site.
reset_work() shrinks to interrupt/worker drain, dispatch on
reset_type, and the single asymmetry between the two paths. The
out_enable label, the manual unregister/register pair, and the
forward declaration of btintel_pcie_setup_hdev() are dropped.
No intended functional change; FLR and PLDR now share one
teardown contract.
Fixes: 256ab9520d ("Bluetooth: btintel_pcie: Support Function level reset")
Assisted-by: GitHub-Copilot:claude-4.7-opus
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During the v3 firmware download the controller sends a v3_data_req with a
32 bit offset and a 16 bit len. nxp_recv_fw_req_v3() checks only the lower
bound of the offset and then sends firmware from that offset.
nxpdev->fw_dnld_v3_offset = offset - nxpdev->fw_v3_offset_correction;
serdev_device_write_buf(nxpdev->serdev, nxpdev->fw->data +
nxpdev->fw_dnld_v3_offset, len);
Nothing checks that fw_dnld_v3_offset + len stays within nxpdev->fw->size,
so a controller that asks for an offset or length past the firmware image
makes the driver read past the end of nxpdev->fw->data and send that
memory back over UART.
nxp_recv_fw_req_v1() already bounds the same write. Add the equivalent
check to the v3 path, reject the request when it falls outside the firmware
image, and zero len on the error path so the fw_v3_prev_sent bookkeeping at
free_skb stays consistent.
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Suggested-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
HCI_UART_SENDING bit in tx_state means write_work is pending and blocks
queueing it again. Currently this bit is not cleared when canceling the
work in hci_uart_close(), which blocks future writes when device is
reopened later if write_work was pending.
Fix by clearing HCI_UART_SENDING when canceling the work.
Also make clearing of tx_skb safe by using disable_work_sync +
enable_work instead of just cancel_work_sync. hci_uart_flush() purges
the proto tx queue so we can cancel the pending write_work there,
instead of doing it just in hci_uart_close(). Re-enable and possibly
requeue the work after queue flush.
Fixes: c1bb9336ae ("Bluetooth: hci_uart: fix UAFs and race conditions in close and init paths")
Link: https://lore.kernel.org/linux-bluetooth/07e0a28650773abec711ee492fdb1bf5d21a6c98.camel@iki.fi/
Cc: stable@vger.kernel.org
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Sharing a single workqueue between coredump processing and RX
delays evacuation of RX events while a coredump is in progress.
The firmware's RX buffers can overflow during that window, leading
to dropped events. The issue was observed in HID use cases where
HID reports arrive in bursts and quickly fill the RX path while a
coredump is being collected.
Move coredump processing to a dedicated ordered coredump_workqueue
with its own coredump_work, so coredumps run independently of RX.
All four coredump trigger sources (FW assert, HW exception, user
sysfs trigger, and resume-error detection) are switched to this new
workqueue. Ordering serialises concurrent triggers without blocking
RX.
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Every once in a while we see a hung btmtksdio_flush() task:
INFO: task kworker/u17:0:189 blocked for more than 122 seconds.
__cancel_work_timer+0x3f4/0x460
cancel_work_sync+0x1c/0x2c
btmtksdio_flush+0x2c/0x40
hci_dev_open_sync+0x10c4/0x2190
[..]
It all boils down to incorrect time_is_before_jiffies() usage in
btmtksdio_txrx_work(). The btmtksdio_txrx_work() loop is expected
to be terminated if running for longer than 5*HZ. However the
timeout check is twisted: time_is_before_jiffies(old_jiffies + 5*HZ)
evaluates to true when old_jiffies + 5*HZ is in the past i.e. when a
timeout has occurred. Using OR with time_is_before_jiffies(txrx_timeout)
means that:
- before the 5-second timeout: the condition is `int_status || false`,
so it loops as long as there are pending interrupts.
- after the 5-second timeout: the condition becomes `int_status || true`,
which is always true.
When the loop becomes infinite btmtksdio_txrx_work() loop never
terminates and never releases the SDIO host.
Fix loop termination condition to actually enforce a 5*HZ timeout.
Fixes: 26270bc189 ("Bluetooth: btmtksdio: move interrupt service to work")
Cc: stable@vger.kernel.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Firmware version is critical for bug triage. Users reporting issues
typically share dmesg output rather than debugfs contents, requiring
extra communication rounds to collect this information. Log the FW
build version directly to the kernel log so it is immediately
available in bug reports.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Xiuzhuo Shang <xiuzhuo.shang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The VHCI force_devcoredump debugfs hook accepts a small test record from
userspace. It validates the requested terminal state only after
registering, initializing and appending a Bluetooth devcoredump.
As a result, an invalid state returns -EINVAL but still leaves queued
devcoredump work behind. With a non-zero timeout field, the rejected
write can still emit a devcoredump after the timeout expires.
Reject unsupported states before allocating the skb or changing the HCI
devcoredump state machine.
Fixes: ab4e4380d4 ("Bluetooth: Add vhci devcoredump support")
Assisted-by: Codex:gpt-5.5-cyber-preview
Signed-off-by: Samuel Moelius <sam.moelius@trailofbits.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Load the IOSF DBGC base address based on the controller hardware
variant when reading DRAM buffers during a trace dump. Scorpius
Peak family controllers (SCP/SCP2/SCP2F) use a different DBGC base
address (0xf0d5d500) than Blazar family controllers (BZRI/BZRIW,
0xf3800300).
Fixes: 07e6bddb54 ("Bluetooth: btintel_pcie: Add support for device coredump")
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On BlazarIW, fast restart cycles fail because the D0 entry to MAC
init does not complete in time. As a result, MAC initialization
does not proceed and the controller fails to transition past the
ROM boot stage.
Add a 50 ms delay (worst case as per HW analysis) before doing MAC
init in btintel_pcie_enable_bt() so the shared hardware reset flow
has time to complete. The delay is gated on the BlazarIW PCI device
id 0x4D76 so other Intel BT PCIe controllers are unaffected.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Many bluetooth source files are missing SPDX-License-Identifier
lines. Add appropriate IDs to these files, and remove other
license lines from the headers.
Leave the warranty disclaimer in files where the license ID is
GPL-2.0 but the wording of the disclaimer is slightly different
from that of the GPL v2 disclaimer.
It is not different enough to cause licensing conflicts, but is
kept to honor the original contributors' legal intent.
Signed-off-by: Tim Bird <tim.bird@sony.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Based on the debug configuration, firmware can raise MSI-X interrupt with
firmware trigger cause bit set on specific events like Disconnection,
Connection Timeout, Page Timeout etc.
Upon receiving an MSI-X interrupt with the firmware trigger cause bit
set, the driver performs the following actions:
1. Reads Device Memory: Retrieves data from the device memory,
constructs an HCI diagnostic event, and sends it to the monitor. This
event includes details about the trigger, such as connection timeout or
page timeout.
2. Dumps Device Coredump: Generates a coredump containing firmware
traces for further analysis.
The coredump can be retrieved using:
$ cat /sys/class/devcoredump/devcd*/data > /tmp/btintel_coredump.bin
HCI traces:
= Vendor Diagnostic (len 12)
a5 a5 a5 a5 01 03 00 23 00 01 00 00
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Unlike the other HCI UART drivers, the 3-wire UART driver doesn't reset
hci_uart::priv in its close() method -- this shouldn't pose a problem as
all the methods in *struct* hci_uart_proto should only be called after the
open() method that sets up hci_uart::priv properly. However, it seems wise
to be more consistent and provide for the *struct* hci_uart_proto methods
the same state that exists before the first open() method call (so that
they rather crash than dereference a stale hci_uart::priv pointer)...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@auroraos.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Clean up probe error handling by using dedicated error labels with an
"err" prefix.
Note that the endpoint lookup helper returns -ENXIO when endpoints are
missing which is functionally equivalent to returning -ENODEV.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
