The TX metadata area resides in the UMEM buffer which is memory-mapped
and concurrently writable by userspace. In xsk_skb_metadata(),
csum_start and csum_offset are read from shared memory for bounds
validation, then read again for skb assignment. A malicious userspace
application can race to overwrite these values between the two reads,
bypassing the bounds check and causing out-of-bounds memory access
during checksum computation in the transmit path.
Fix this by reading csum_start and csum_offset into local variables
once, then using the local copies for both validation and assignment.
Note that other metadata fields (flags, launch_time) and the cached
csum fields may be mutually inconsistent due to concurrent userspace
writes, but this is benign: the only security-critical invariant is
that each field's validated value is the same one used, which local
caching guarantees.
Closes: https://lore.kernel.org/all/20260503200927.73EA1C2BCB4@smtp.kernel.org/
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Fixes: 48eb03dd26 ("xsk: Add TX timestamp and TX checksum offload support")
Link: https://patch.msgid.link/20260530042630.80626-1-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix host controller programming for eMMC fixed driver type
MMC host:
- dw_mmc-rockchip: Add missing private data for very old controllers
- litex_mmc: Fix clock management
- renesas_sdhi: Add OF entry for RZ/G2H SoC
- sdhci: Manage signal voltage switch during system resume for some hosts
- sdhci-of-dwcmshc: Fix reset, clk and SDIO support for Eswin EIC7700"
* tag 'mmc-v7.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci: add signal voltage switch in sdhci_resume_host
mmc: dw_mmc-rockchip: Add missing private data for very old controllers
mmc: litex_mmc: Set mandatory idle clocks before CMD0
mmc: litex_mmc: Use DIV_ROUND_UP for more accurate clock calculation
mmc: renesas_sdhi: Add OF entry for RZ/G2H SoC
mmc: sdhci-of-dwcmshc: Fix reset, clk, and SDIO support for Eswin EIC7700
mmc: core: Fix host controller programming for fixed driver type
Pull cgroup fixes from Tejun Heo:
"One cpuset fix and a maintenance update, both low-risk:
- Fix cpuset partition CPU accounting under sibling CPU exclusion
that could produce wrong CPU assignments and trigger
scheduling-domain warnings. Includes selftests.
- Update an email address in MAINTAINERS"
* tag 'cgroup-for-7.1-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup/cpuset: Change Ridong's email
cgroup/cpuset: Add test cases for sibling CPU exclusion on partition update
cgroup/cpuset: Use effective_xcpus in partcmd_update add/del mask calculation
Pull sched_ext fixes from Tejun Heo:
"Two low-risk fixes:
- Drop a spurious warning that can fire during cgroup migration while
a sched_ext scheduler is loaded
- Fix a drgn-based debug script that broke after scheduler state
moved into a per-scheduler struct"
* tag 'sched_ext-for-7.1-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Don't warn on NULL cgrp_moving_from in scx_cgroup_move_task()
tools/sched_ext: Fix scx_show_state per-scheduler state reads
bluetoothd has a bug with makes it send extra bytes as part of
MGMT_OP_ADD_EXT_ADV_DATA which are now being checked to be the
exact the expected length, relax this so only when the expected
length is greater than the data length to cause an error since
that would result in accessing invalid memory, otherwise just
ignore the extra bytes.
Link: https://lore.kernel.org/linux-bluetooth/20260602204749.210857-1-luiz.dentz@gmail.com/T/#u
Fixes: d3f7d17960 ("Bluetooth: MGMT: validate Add Extended Advertising Data length")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
sco_sock_connect() copies the destination address into sco_pi(sk)->dst
under lock_sock(), then releases the lock and calls sco_connect(),
which reads dst, src, setting, and codec without holding lock_sock() in
hci_get_route() and hci_connect_sco().
These fields may be modified concurrently by connect(), bind(), or
setsockopt() on the same socket, resulting in data-races reported by
KCSAN.
Fix this by snapshotting dst, src, setting, and codec under lock_sock()
at the start of sco_connect() before passing them to hci_get_route()
and hci_connect_sco().
BUG: KCSAN: data-race in memcmp+0x45/0xb0
race at unknown origin, with read to 0xffff88800e6b0dd0 of 1 bytes
by task 315 on cpu 0:
memcmp+0x45/0xb0
hci_connect_acl+0x1b7/0x6b0
hci_connect_sco+0x4d/0xb30
sco_sock_connect+0x27b/0xd60
__sys_connect_file+0xbd/0xe0
__sys_connect+0xe0/0x110
__x64_sys_connect+0x40/0x50
x64_sys_call+0xcad/0x1c60
do_syscall_64+0x133/0x590
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: 9a8ec9e8eb ("Bluetooth: SCO: Fix possible circular locking dependency on sco_connect_cfm")
Signed-off-by: SeungJu Cheon <suunj1331@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
iso_connect_bis(), iso_connect_cis(), iso_listen_bis(), and
iso_conn_big_sync() call hci_get_route() using iso_pi(sk)->dst,
iso_pi(sk)->src, and iso_pi(sk)->src_type without holding lock_sock().
These fields may be modified concurrently by connect() or setsockopt()
on the same socket, resulting in data-races reported by KCSAN.
Fix this by snapshotting the required fields under lock_sock() before
calling hci_get_route().
BUG: KCSAN: data-race in memcmp+0x45/0xb0
race at unknown origin, with read to 0xffff8880122135cf of 1 bytes
by task 333 on cpu 1:
memcmp+0x45/0xb0
hci_get_route+0x27e/0x490
iso_connect_cis+0x4c/0xa10
iso_sock_connect+0x60e/0xb30
__sys_connect_file+0xbd/0xe0
__sys_connect+0xe0/0x110
__x64_sys_connect+0x40/0x50
x64_sys_call+0xcad/0x1c60
do_syscall_64+0x133/0x590
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: 241f51931c ("Bluetooth: ISO: Avoid circular locking dependency")
Signed-off-by: SeungJu Cheon <suunj1331@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In iso_sock_rebind_bc(), the bis pointer is cached, then the socket lock is
dropped:
bis = iso_pi(sk)->conn->hcon;
/* Release the socket before lookups since that requires hci_dev_lock
* which shall not be acquired while holding sock_lock for proper
* ordering.
*/
release_sock(sk);
hci_dev_lock(bis->hdev);
During the unlocked window, could a concurrent close() destroy the connection
and free the bis structure, causing hci_dev_lock(bis->hdev) to access memory
after it is freed, fix this by using the hdev reference which was safely
acquired via iso_conn_get_hdev().
Fixes: d3413703d5 ("Bluetooth: ISO: Add support to bind to trigger PAST")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_get_route() returns a reference-counted hci_dev pointer via
hci_dev_hold(). The function exits normally or with an error without ever
releasing it.
Fixes: 07a9342b94 ("Bluetooth: ISO: Send BIG Create Sync via hci_sync")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Early failures in Bluetooth HCI UART configuration leak SRCU percpu
memory.
When device initialization fails before hci_register_dev() completes,
the HCI_UNREGISTER flag is never set. As a result, when the device
reference count reaches zero, bt_host_release() evaluates this flag as
false and falls back to a direct kfree(hdev).
Because hci_release_dev() is bypassed, the SRCU struct initialized
early in hci_alloc_dev() is never cleaned up, resulting in a leak of
percpu memory.
Fix the leak by explicitly calling cleanup_srcu_struct() in the
fallback (unregistered) branch of bt_host_release() before freeing
the device.
Reported-by: syzbot+535ecc844591e50588a5@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=535ecc844591e50588a5
Tested-by: syzbot+535ecc844591e50588a5@syzkaller.appspotmail.com
Fixes: 1d6123102e ("Bluetooth: hci_core: Fix use-after-free in vhci_flush()")
Signed-off-by: Bharath Reddy <kbreddy.rpbc@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A BNEP peer can send a short BNEP SDU. bnep_rx_frame() reads the
packet type byte immediately and, for control packets, reads the control
opcode and setup UUID-size byte before proving that those bytes are
present. bnep_rx_control() also dereferences the control opcode without
rejecting an empty control payload.
Use skb_pull_data() for the fixed fields in bnep_rx_frame() so a NULL
return gates each dereference. Split the control handler so the frame
path can pass an opcode that has already been pulled, and keep the
byte-buffer wrapper for extension control payloads.
For BNEP_SETUP_CONN_REQ, name the UUID-size byte before pulling the
setup payload. struct bnep_setup_conn_req carries destination and source
service UUIDs after that byte, each uuid_size bytes, so the parser now
documents that tuple explicitly instead of leaving the pull length as an
opaque multiplication.
Validation reproduced this kernel report:
KASAN slab-out-of-bounds in bnep_rx_frame.isra.0+0x130c/0x1790
The buggy address belongs to the object at ffff88800c0f7908 which belongs
to the cache kmalloc-8 of size 8
The buggy address is located 0 bytes to the right of allocated 1-byte
region [ffff88800c0f7908, ffff88800c0f7909)
Read of size 1
Call trace:
dump_stack_lvl+0xb3/0x140 (?:?)
print_address_description+0x57/0x3a0 (?:?)
bnep_rx_frame+0x130c/0x1790 (net/bluetooth/bnep/core.c:306)
print_report+0xb9/0x2b0 (?:?)
__virt_addr_valid+0x1ba/0x3a0 (?:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
kasan_addr_to_slab+0x21/0x60 (?:?)
kasan_report+0xe0/0x110 (?:?)
process_one_work+0xfce/0x17e0 (kernel/workqueue.c:3200)
worker_thread+0x65c/0xe40 (?:?)
__kthread_parkme+0x184/0x230 (?:?)
kthread+0x35e/0x470 (?:?)
_raw_spin_unlock_irq+0x28/0x50 (?:?)
ret_from_fork+0x586/0x870 (?:?)
__switch_to+0x74f/0xdc0 (?:?)
ret_from_fork_asm+0x1a/0x30 (?:?)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Assisted-by: Codex:gpt-5.5
Signed-off-by: Zhang Cen <rollkingzzc@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Existing advertising instances can already hold the maximum extended
advertising payload. When hci_adv_bcast_annoucement() prepends the
Broadcast Announcement service data to that payload, the combined data
may no longer fit in the temporary buffer used to rebuild the
advertising data.
Reject that case before copying the existing payload and report the
failure through the device log. This keeps the existing advertising
data intact and avoids overrunning the temporary buffer.
Fixes: 5725bc6082 ("Bluetooth: hci_sync: Fix broadcast/PA when using an existing instance")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Zhengchuan Liang <zcliangcn@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Assisted-by: Codex:GPT-5.4
Signed-off-by: Yuqi Xu <xuyq21@lenovo.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
net/bluetooth/l2cap_core.c:l2cap_sig_channel() accepts BR/EDR
signaling packets up to the channel MTU and dispatches each command
without enforcing the signaling MTU (MTUsig). A Bluetooth BR/EDR peer
within radio range can send a fixed-channel CID 0x0001 packet that is
larger than MTUsig and contains many L2CAP_ECHO_REQ commands before
pairing. In a real-radio stock-kernel run, one 681-byte signaling
packet containing 168 zero-length ECHO_REQ commands made the target
transmit 168 ECHO_RSP frames over about 220 ms.
Impact: a Bluetooth BR/EDR peer within radio range, before pairing, can
force 168 ECHO_RSP frames from one 681-byte fixed-channel signaling
packet containing packed ECHO_REQ commands.
Define Linux's BR/EDR signaling MTU as the spec minimum of 48 bytes and
reject any larger signaling packet with one L2CAP_COMMAND_REJECT_RSP
carrying L2CAP_REJ_MTU_EXCEEDED before any command is dispatched.
The Bluetooth Core spec wording for MTUExceeded says the reject
identifier shall match the first request command in the packet, and
that packets containing only responses shall be silently discarded.
Linux intentionally deviates from that prescription: silently
discarding desynchronizes the peer because the remote stack never
learns its responses were dropped, and locating the first request
command requires walking command headers past MTUsig, i.e. processing
bytes from a packet we have already decided is too large to process.
We therefore always emit one reject and use the identifier from the
first command header, a single fixed-offset byte read.
The unrestricted BR/EDR signaling parser and ECHO_REQ response path both
trace to the initial git import; no later introducing commit is
available for a Fixes tag.
Cc: stable@vger.kernel.org
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20260518002800.1361430-1-michael.bommarito@gmail.com
Link: https://lore.kernel.org/r/20260520135034.1060859-1-michael.bommarito@gmail.com
Link: https://lore.kernel.org/r/20260521000555.3712030-1-michael.bommarito@gmail.com
Assisted-by: Claude:claude-opus-4-7
Assisted-by: Codex:gpt-5-5-xhigh
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The RFCOMM MCC handlers cast skb->data to protocol-specific structs
without validating skb->len first. A malicious remote device can send
truncated MCC frames and trigger out-of-bounds reads in these handlers.
Fix this by using skb_pull_data() to validate and access the required
data before dereferencing it.
rfcomm_recv_rpn() requires special handling since ETSI TS 07.10 allows
1-byte RPN requests. Handle this by validating only the DLCI byte first,
and validating the full struct only when len > 1.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Suggested-by: Muhammad Bilal <meatuni001@gmail.com>
Signed-off-by: SeungJu Cheon <suunj1331@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
tlv_data_is_valid() reads each advertising data field length from
data[i], then inspects data[i + 1] for managed EIR types before
checking that the current field still fits inside the supplied buffer.
A malformed field whose length byte is the last byte of the buffer can
therefore make the parser read one byte past the advertising data.
KASAN reported the following when a malformed MGMT_OP_ADD_ADVERTISING
request reached that path:
BUG: KASAN: vmalloc-out-of-bounds in tlv_data_is_valid()
Read of size 1
Call trace:
tlv_data_is_valid()
add_advertising()
hci_mgmt_cmd()
hci_sock_sendmsg()
Move the existing element-length check before any type-octet inspection
so each non-empty element is proven to contain its type byte before the
parser looks at data[i + 1].
Fixes: 2bb36870e8 ("Bluetooth: Unify advertising instance flags check")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Zhang Cen <rollkingzzc@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_get_sock_by_channel() scans rfcomm_sk_list under the list lock,
but returns the selected listener after dropping that lock without
taking a reference. rfcomm_connect_ind() then locks the listener,
queues a child socket on it, and may notify it after unlocking it.
The buggy scenario involves two paths, with each column showing the
order within that path:
rfcomm_connect_ind(): listener close:
1. Find parent in 1. close() enters
rfcomm_get_sock_by_channel() rfcomm_sock_release().
2. Drop rfcomm_sk_list.lock 2. rfcomm_sock_shutdown()
without pinning parent. closes the listener.
3. Call lock_sock(parent) and 3. rfcomm_sock_kill()
bt_accept_enqueue(parent, unlinks and puts parent.
sk, true).
4. Read parent flags and may 4. parent can be freed.
call sk_state_change().
If close wins the race, parent can be freed before
rfcomm_connect_ind() reaches lock_sock(), bt_accept_enqueue(), or the
deferred-setup callback.
Take a reference on the listener before leaving rfcomm_sk_list.lock.
After lock_sock() succeeds, recheck that it is still in BT_LISTEN
before queueing a child, cache the deferred-setup bit while the parent
is locked, and drop the reference after the last parent use.
KASAN reported a slab-use-after-free in lock_sock_nested() from
rfcomm_connect_ind(), with the freeing stack going through
rfcomm_sock_kill() and rfcomm_sock_release().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zhang Cen <rollkingzzc@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
wifi: iwlwifi: fixes - 2026-05-31
Miri Korenblit says:
====================
This contains a few fixes:
- Don't grab nic access in non-fast-resume
- Don't send a large hcmd than transport supports
- In AP mode, don't send tx power constraints command before activating
the link
- Don't do sw reset handshake on older firmwares.
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rdev->int_scan_req is leaked if cfg80211_scan() fails. Note that it's
supposed to be released at ___cfg80211_scan_done() but this doesn't happen
as rdev->scan_req is NULL at that point, too, leading to the early return
from the freeing function.
unreferenced object 0xffff8881161d0800 (size 512):
comm "wpa_supplicant", pid 379, jiffies 4294749765
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 f0 81 13 16 81 88 ff ff ................
backtrace (crc c867fdb6):
kmemleak_alloc+0x89/0x90
__kmalloc_noprof+0x2fd/0x410
cfg80211_scan+0x133/0x730
nl80211_trigger_scan+0xc69/0x1cc0
genl_family_rcv_msg_doit+0x204/0x2f0
genl_rcv_msg+0x431/0x6b0
netlink_rcv_skb+0x143/0x3f0
genl_rcv+0x27/0x40
netlink_unicast+0x4f6/0x820
netlink_sendmsg+0x797/0xce0
__sock_sendmsg+0xc4/0x160
____sys_sendmsg+0x5e4/0x890
___sys_sendmsg+0xf8/0x180
__sys_sendmsg+0x136/0x1e0
__x64_sys_sendmsg+0x76/0xc0
x64_sys_call+0x13f0/0x17d0
Found by Linux Verification Center (linuxtesting.org).
Fixes: c8cb5b854b ("nl80211/cfg80211: support 6 GHz scanning")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Link: https://patch.msgid.link/20260601094157.92703-1-pchelkin@ispras.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
syzbot reported a splat [1]: a slab-use-after-free in
ipv6_chk_acast_addr(), which walks the global inet6_acaddr_lst[] hash
under RCU and dereferences a struct ifacaddr6 that has already been
freed while still linked in the hash, so a later reader walks into a
dangling node.
In __ipv6_dev_ac_inc() the aca is allocated with refcount 1, then
aca_get() bumps it to 2 to keep it alive across the unlocked region.
It is published to idev->ac_list under idev->lock, but
ipv6_add_acaddr_hash() runs after write_unlock_bh(). A concurrent
teardown (ipv6_ac_destroy_dev() from addrconf_ifdown(), under RTNL)
can slip into that window:
CPU0 __ipv6_dev_ac_inc CPU1 ipv6_ac_destroy_dev (RTNL)
------------------------------ ------------------------------------
aca_alloc() refcnt 1
aca_get() refcnt 2
write_lock_bh(idev->lock)
add aca to ac_list
write_unlock_bh(idev->lock)
write_lock_bh(idev->lock)
pull aca off ac_list
write_unlock_bh(idev->lock)
ipv6_del_acaddr_hash(aca)
hlist_del_init_rcu() is a no-op,
aca is not in the hash yet
aca_put() refcnt 2->1
ipv6_add_acaddr_hash(aca)
aca now inserted into the hash
aca_put() refcnt 1->0
call_rcu(aca_free_rcu) -> kfree(aca)
The hash removal becomes a no-op because the insertion has not
happened yet, so once CPU0 inserts and drops the last reference, the
aca is freed while still linked in inet6_acaddr_lst[], and readers
dereference freed memory after the slab slot is reused.
This window opened once RTNL stopped serializing the join path against
device teardown. Move ipv6_add_acaddr_hash() inside the idev->lock
section so the ac_list and hash insertions are atomic with respect to
teardown: a racing remover now either misses the aca entirely or finds
it in both lists.
acaddr_hash_lock is now nested under idev->lock, which is acquired in
softirq context, so switch all acaddr_hash_lock sites to spin_lock_bh()
to avoid the irq lock inversion reported in [2].
[1] https://syzkaller.appspot.com/bug?extid=a01df04303c131efbf3a
[2] https://lore.kernel.org/netdev/6a194ef7.ba3b1513.1890b4.0000.GAE@google.com/
Reported-by: syzbot+819eb928d120d2bdad0e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/6a191f87.ce022c6e.138e56.0003.GAE@google.com/T/
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Fixes: eb1ac9ff6c ("ipv6: anycast: Don't hold RTNL for IPV6_JOIN_ANYCAST.")
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260529152219.235475-1-jiayuan.chen@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A WARN fires when systemd's user manager writes "+cpu +memory +pids" to
its own subtree_control while a sched_ext scheduler is loaded:
WARNING: at kernel/sched/ext.c:3227 scx_cgroup_move_task+0xa8/0xb0
scx_cgroup_move_task+0xa8/0xb0
sched_move_task+0x134/0x290
cpu_cgroup_attach+0x39/0x70
cgroup_migrate_execute+0x37d/0x450
cgroup_update_dfl_csses+0x1e3/0x270
cgroup_subtree_control_write+0x3e7/0x440
scx_cgroup_can_attach() arms cgrp_moving_from only when a task's cpu
cgroup changes. It can still be NULL when scx_cgroup_move_task() runs,
through this sequence:
Step Result
--------------------------------- ----------------------------------
1. cpu enabled on cgroup G cpu css = A
2. cpu toggled off then on for G A killed, B created (same cgroup)
3. an exiting task keeps A alive migration skips it, A now stale
4. +memory migrates G stale A vs current B pulls cpu in
5. cpu attach runs for all tasks hits a live, cpu-unchanged task
6. scx_cgroup_move_task() on it cgrp_moving_from NULL -> WARN
The mismatch is that scx_cgroup_can_attach() keys on cgroup identity
while migration drives the move on css identity, so a NULL cgrp_moving_from
here is a legitimate css-only migration, not a missing prep.
The call is already gated on cgrp_moving_from, so just drop the warning.
ops.cgroup_prep_move() and ops.cgroup_move() stay paired.
Fixes: 8195136669 ("sched_ext: Add cgroup support")
Cc: stable@vger.kernel.org # v6.12+
Reported-by: Matt Fleming <mfleming@cloudflare.com>
Closes: https://lore.kernel.org/all/20260601124156.2205704-1-mfleming@cloudflare.com/
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andrea Righi <arighi@nvidia.com>
The SCTP exact sock_diag lookup can hold a transport reference, block on
lock_sock(sk), and then resume after sctp_association_free() has marked
the association dead and freed its bind address list.
When that happens, inet_assoc_attr_size() and
inet_diag_msg_sctpasoc_fill() can still dereference association state
that is no longer valid for reporting. In particular,
inet_diag_msg_sctpasoc_fill() may read an empty bind-address list as a
real sctp_sockaddr_entry and trigger an out-of-bounds read from
unrelated association memory.
Reject the association after taking the socket lock if it has been
reaped or detached from the endpoint, and report the lookup as stale.
This keeps the exact dump-one path from formatting torn association
state.
Fixes: 8f840e47f1 ("sctp: add the sctp_diag.c file")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Zhengchuan Liang <zcliangcn@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Zhao Zhang <zzhan461@ucr.edu>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/fac6043fa20a2ff68e12958c431836f692c51268.1780113823.git.zzhan461@ucr.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In fec_resume(), fec_enet_clk_enable() is called before
pinctrl_pm_select_default_state() in the non-WoL path, inverting the
ordering used in fec_suspend() which correctly switches to the sleep
pinctrl state before disabling clocks.
For PHYs with the PHY_RST_AFTER_CLK_EN flag (e.g. TI DP83848 or
SMSC LAN87xx), fec_enet_clk_enable() triggers a hardware reset pulse
via the phy-reset GPIO. With the GPIO pin still in sleep pinctrl state
at that point, the GPIO write has no physical effect and the PHY never
receives the required reset after clock enable, leading to unreliable
link establishment after system resume.
Fix by restoring the default pinctrl state before enabling clocks,
making resume the proper mirror of suspend. The call is made
unconditionally: fec_suspend() only switches to the sleep pinctrl state
on the non-WoL path and leaves the pins in the default state when WoL
is enabled, so on a WoL resume the device is already in the default
state and pinctrl_pm_select_default_state() is a no-op.
Fixes: de40ed31b3 ("net: fec: add Wake-on-LAN support")
Signed-off-by: Tapio Reijonen <tapio.reijonen@vaisala.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260529-b4-fec-resume-pinctrl-order-v3-1-6eda0f592fca@vaisala.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VLAN-tagged interfaces on lan743x devices were previously unreachable via
SSH and failed to respond to large ping packets (e.g. "ping -s 1469" given
MTU=1500). In these scenarios, "ethtool -S" reports non-zero "RX Oversize
Frame Errors". According to Microchip AN2948, the MAC_RX FSE (VLAN field
size enforcement) bit determines whether frames with VLAN tags exceeding
the base MTU plus tag length are discarded.
The driver must set the MAC_RX.FSE bit before setting MAC_RX.RXEN to allow
VLAN-tagged frames up to the interface MTU, preventing them from being
treated as oversized. As a result, both the base and VLAN-tagged interfaces
can use the same MTU without receive errors.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Thangaraj Samynathan <Thangaraj.s@microchip.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de> # lan7430 on arm64 (RevPi
Link: https://patch.msgid.link/20260529210300.433135-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
