Setting up the interface when suspended/resumeing fail on this card.
Adding a reset and delay quirk will eliminate this problem.
usb 1-1: new full-speed USB device number 2 using xhci-hcd
usb 1-1: New USB device found, idVendor=25aa, idProduct=600b
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: TAE1159
usb 1-1: Manufacturer: Generic
usb 1-1: SerialNumber: 20210726905926
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Link: https://patch.msgid.link/TYUPR06MB621736D7C85D43200E54E740D2082@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Firmware 2417 for the Scarlett 4th Gen 2i2 moved the direct monitor
gain parameter by 4 bytes, from offset 0x2a0 to 0x2a4, breaking the
"Direct Monitor X Mix Y" controls.
Special-case the offset in the get/set config helpers when the
running firmware is 2417 or later.
Fixes: 4e809a2996 ("ALSA: scarlett2: Add support for Solo, 2i2, and 4i4 Gen 4")
Cc: <stable@vger.kernel.org>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://patch.msgid.link/ahIWTueUlWA5xiV+@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
scarlett2_hwdep_write() rejects writes when offset + count is greater than
or equal to the selected flash segment size. That incorrectly treats a
write ending exactly at the end of the segment as out of space, although
the last byte written is still within the segment.
Split invalid argument checks from the segment-space check, keep
zero-length writes as no-ops, and compare count against the remaining
segment size. This permits exact-end writes and avoids relying on
offset + count before deciding whether the request is in bounds.
Fixes: 1abfbd3c95 ("ALSA: scarlett2: Add support for uploading new firmware")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260519-alsa-scarlett2-flash-write-boundary-v1-1-b550480e92da@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
find_format_descriptor() walks the class-specific interface extras by
advancing with bLength. It rejects descriptors that extend past the
remaining buffer, but it does not reject descriptor lengths smaller than
a USB descriptor header.
Reject too-short descriptors before using bLength to advance the local
scan. This keeps the UA-101 parser robust against malformed descriptor
data and matches the usual USB descriptor walking rules.
Fixes: 63978ab3e3 ("sound: add Edirol UA-101 support")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260519-alsa-ua101-desc-len-v1-1-4307d1a5e054@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
uaudio_transfer_buffer_setup() calls dma_get_sgtable() and then passes
the sg_table to uaudio_iommu_map_xfer_buf() without checking whether sg
table construction succeeded. If dma_get_sgtable() fails, the sg_table
contents are not valid.
uaudio_iommu_map_pa() also ignores iommu_map() failures for the event and
transfer rings and still returns the allocated IOVA to the QMI response.
That can expose an unmapped IOVA to the audio DSP. For transfer rings,
the failed mapping also leaves the IOVA allocator state marked in use.
Check both operations. Free the coherent transfer buffer when sg table
construction fails, free the sg table when transfer-buffer IOMMU mapping
fails, and release the transfer-ring IOVA if iommu_map() fails. Also
return the existing event-ring IOVA when the event ring is already mapped,
matching the pre-split helper behavior.
Fixes: 326bbc3482 ("ALSA: usb-audio: qcom: Introduce QC USB SND offloading support")
Fixes: 44499ecb4f ("ALSA: usb: qcom: Fix false-positive address space check")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260511-alsa-usb-qcom-offload-map-errors-v1-1-6502695e58bc@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting up the interface when suspended/resumeing fail on this card.
Adding a reset and delay quirk will eliminate this problem.
usb 1-1: new full-speed USB device number 2 using xhci-hcd
usb 1-1: New USB device found, idVendor=3302, idProduct=17c2
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: USB-C Audio
usb 1-1: Manufacturer: TTGK Technology
usb 1-1: SerialNumber: 170120210706
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/TYUPR06MB621720E4E8F99A42E162FD51D23D2@TYUPR06MB6217.apcprd06.prod.outlook.com
When initialise new control with scarlett2_add_new_ctl() function for
Autogain Status, scarlett2_add_new_ctl() might throw an error. So, add
error check after initialise new control for Autogain Status.
This is reported by Coverity Scan with CID 1598781 as UNUSED_VALUE.
Fixes: 0a995e38dc ("ALSA: scarlett2: Add support for software-controllable input gain")
Signed-off-by: Robertus Diawan Chris <robertusdchris@gmail.com>
Link: https://patch.msgid.link/20260508033914.111596-1-robertusdchris@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The USB MIDI 2.0 endpoint parser has the same descriptor walking
pattern as the legacy MIDI parser. It validates bLength against
bNumGrpTrmBlock before reading baAssoGrpTrmBlkID[], but not against the
remaining bytes in the endpoint-extra scan.
A malformed device can therefore make later baAssoGrpTrmBlkID[] reads
consume bytes past the walked descriptor.
Reject zero-length and overlong descriptors while walking endpoint
extras.
Fixes: ff49d1df79 ("ALSA: usb-audio: USB MIDI 2.0 UMP support")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260507-usb-midi-endpoint-scan-bounds-v1-2-329d7348160e@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_usbmidi_get_ms_info() validates the internal MIDIStreaming endpoint
descriptor size before using baAssocJackID[], but the descriptor walker can
still return a class-specific endpoint descriptor whose bLength exceeds the
remaining bytes in the endpoint-extra scan.
That leaves later flexible-array reads bounded by bLength, but not by the
remaining bytes in the endpoint-extra scan.
Stop walking when bLength is zero or
extends past the remaining endpoint-extra scan.
Fixes: 5c6cd7021a ("ALSA: usb-audio: Fix case when USB MIDI interface has more than one extra endpoint descriptor")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260507-usb-midi-endpoint-scan-bounds-v1-1-329d7348160e@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Motu 1248 (and probably other older Motu AVB interfaces) take more
than 2 seconds to switch clock. During the clock switching process the
device return that the clock is not valid. This is similar to what
already implemented for the Microbook II interface. Add the Motu
1248 usb id to the existing Motu quirk.
Signed-off-by: Nicola Lunghi <nick83ola@gmail.com>
Link: https://patch.msgid.link/20260504144520.699522-2-nick83ola@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB MIDI 2.0 suspend saves the endpoint running state, clears it and
kills all endpoint URBs. Resume restores the running state, but only
restarts input endpoints.
For a running output endpoint, this leaves the endpoint marked running
with an empty URB queue. Output transfer progress depends on either the
rawmidi trigger path starting the queue or an output completion refilling
it. After suspend there is no completion left, and output data that
remains queued in the raw UMP or legacy rawmidi buffer can stay stalled
until userspace happens to trigger the stream again.
Restore the saved state with atomic accessors, keep input endpoints
restarted as before, and restart output endpoints that were running before
suspend. Clear the saved suspend state after restoring it.
Fixes: ff49d1df79 ("ALSA: usb-audio: USB MIDI 2.0 UMP support")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260504-usb-midi2-output-resume-v1-1-c089cc8ad3c6@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
JBL Pebbles is a pair of desktop speakers with UAC interface. Its
Playback and Capture mixers use linear volume with val = 0/999/1 and
0/3996/4. Meanwhile, the reported sample rates are truncated to
multiples of 0x100 (i.e., 44100 => 44032), resulting in noisy kmsg, as a
warning message is printed each time a stream is opened.
Add a quirk table entry matching VID/PID=0x05fc/0x0231 and applying
linear volume and sample rate quirk flags, so that it can work properly.
Also note that the volume control knob on device is an incremental
encoder. It does nothing but sends KEY_VOLUMEUP and KEY_VOLUMEDOWN per
rotation, controlling the UAC Playback volume mixer indirectly. Hence,
the linear volume quirk flags also enable the volume control knob to
function properly.
Quirky device sample:
usb 5-1.1: new full-speed USB device number 12 using xhci_hcd
usb 5-1.1: New USB device found, idVendor=05fc, idProduct=0231, bcdDevice= 1.00
usb 5-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-1.1: Product: JBL Pebbles
usb 5-1.1: Manufacturer: Harman International Industries
usb 5-1.1: SerialNumber: 1.0.0
usb-storage 5-1.1:1.0: USB Mass Storage device detected
scsi host0: usb-storage 5-1.1:1.0
usb 5-1.1: Found last interface = 1
usb 5-1.1: 2:1: add audio endpoint 0x5
usb 5-1.1: Creating new data endpoint #5
usb 5-1.1: 2:1 Set sample rate 44100, clock 0
usb 5-1.1: current rate 44032 is different from the runtime rate 44100
usb 5-1.1: 3:1: add audio endpoint 0x84
usb 5-1.1: Creating new data endpoint #84
usb 5-1.1: 3:1 Set sample rate 44100, clock 0
usb 5-1.1: current rate 44032 is different from the runtime rate 44100
usb 5-1.1: [2] FU [PCM Playback Switch] ch = 1, val = 0/1/1
usb 5-1.1: Warning! Unlikely big volume step count (=999), linear volume or wrong cval->res?
usb 5-1.1: [2] FU [PCM Playback Volume] ch = 2, val = 0/999/1
usb 5-1.1: [5] FU [Mic Capture Switch] ch = 1, val = 0/1/1
usb 5-1.1: Warning! Unlikely big volume step count (=999), linear volume or wrong cval->res?
usb 5-1.1: [5] FU [Mic Capture Volume] ch = 2, val = 0/3996/4
input: Harman International Industries JBL Pebbles as /devices/pci0000:00/0000:00:08.3/0000:67:00.3/usb5/5-1/5-1.1/5-1.1:1.4/0003:05FC:0231.0018/input/input55
hid-generic 0003:05FC:0231.0018: input,hidraw2: USB HID v2.01 Device [Harman International Industries JBL Pebbles] on usb-0000:67:00.3-1.1/input4
Signed-off-by: Rong Zhang <i@rong.moe>
Link: https://patch.msgid.link/20260504-uac-jbl-pebbles-v1-1-c888d592a286@rong.moe
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The AlphaTheta EUPHONIA (VID 0x2b73, PID 0x0047) is a USB Audio
Class 2 DJ mixer that requires implicit feedback for full-duplex
operation. The capture endpoint (0x83 IN, interface 2) acts as the
implicit feedback source for the playback endpoint (0x03 OUT,
interface 1), and the device firmware does not send isochronous
data on the capture endpoint unless the host is simultaneously
sending data on the playback endpoint, i.e. playback must be
started first.
Without QUIRK_FLAG_PLAYBACK_FIRST the kernel waits for capture URBs
before submitting playback URBs, creating a deadlock: the device
waits for playback data and the host waits for capture data.
Without QUIRK_FLAG_GENERIC_IMPLICIT_FB the kernel does not detect
the implicit feedback relationship between the two interfaces.
The same flag combination is already used for the Behringer UMC202HD,
UMC204HD and UMC404HD (0x1397:0x0507/0x0508/0x0509), which exhibit
the identical implicit-feedback topology.
Tested on Raspberry Pi 5 with kernel 6.12.75; continuous full-duplex
streaming at 96 kHz / 24-bit, zero XRUNs.
Signed-off-by: Anton Swart <anton.swart.jhb@gmail.com>
Link: https://patch.msgid.link/20260503211517.14332-1-anton.swart.jhb@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The convert_chmap_v3() has a loop with its increment size of
cs_desc->wLength, but we forgot to validate cs_desc->wLength itself,
which may lead to potential endless loop by a malformed descriptor.
Add a proper size check to abort the loop for plugging the hole.
Fixes: ecfd41166b ("ALSA: usb-audio: Validate UAC3 cluster segment descriptors")
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260427152224.15276-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At parsing UAC3 streams, we allocate a PD object at each time, and
either assign or free it. But there is a case where the PD object may
be leaked; namely, in __snd_usb_parse_audio_interface() loop, when an
audioformat shares the same endpoint with others, it's put to a link
and returns from snd_usb_add_audio_stream(), but the PD is forgotten
afterwards. Overall, the treatment of PD object in the parser code is
a bit flaky, and we should be more careful about the object ownership.
This patch tries to fix the above case and improve the code a bit.
The pd object is now managed with the auto-cleanup in the loop, and
the ownership is updated when the pd object gets assigned to the
stream, which guarantees the release of the leftover object.
Fixes: 7edf3b5e6a ("ALSA: usb-audio: AudioStreaming Power Domain parsing")
Link: https://patch.msgid.link/20260427151508.12544-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous fix for handling the error from setup_card() missed that
an internal URB cdev->ep1_in_urb might have been already submitted
beforehand. In the normal case, this URB gets killed at the
disconnection, but in the error path, we didn't do it, hence there can
be a potential leak.
Fix it in the error path for setup_card(), too.
Fixes: 28abd224db ("ALSA: caiaq: Handle probe errors properly")
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260427123819.890185-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
create_card() takes a reference on the USB device with usb_get_dev()
and stores the matching usb_put_dev() in card_free(), which is
installed as the snd_card's ->private_free destructor.
However, ->private_free is only assigned near the end of init_card(),
after several failure points (usb_set_interface(), EP type checks,
usb_submit_urb(), the EP1_CMD_GET_DEVICE_INFO exchange, and its
timeout). When any of those fail, init_card() returns an error to
snd_probe(), which calls snd_card_free(card). Because ->private_free
is still NULL, card_free() never runs, the usb_get_dev() reference
is not dropped, and the struct usb_device leaks along with its
descriptor allocations and device_private.
syzbot reproduces this with a malformed UAC3 device whose only valid
altsetting is 0; init_card()'s usb_set_interface(usb_dev, 0, 1) call
fails with -EIO and triggers the leak.
Move the ->private_free assignment into create_card(), immediately
after usb_get_dev(), so that every error path reaching snd_card_free()
balances the reference. card_free()'s callees (snd_usb_caiaq_input_free,
free_urbs, kfree) already tolerate the partially-initialized state
because the chip private area is zero-initialized by snd_card_new().
Fixes: 80bb50e2d4 ("ALSA: caiaq: take a reference on the USB device in create_card()")
Reported-by: syzbot+2afd7e71155c7e241560@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2afd7e71155c7e241560
Tested-by: syzbot+2afd7e71155c7e241560@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Deepanshu Kartikey <kartikey406@gmail.com>
Link: https://patch.msgid.link/20260426001934.70813-1-kartikey406@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a missing sanity check for bNrChannels in detect_usb_format()
to prevent a division by zero in playback_urb_complete() and
capture_urb_complete().
USB core does not validate class-specific descriptor fields such
as bNrChannels, so drivers must verify them before use. If a
device provides bNrChannels = 0, frame_bytes becomes zero and is
later used as a divisor in the URB completion handlers, leading
to a kernel crash.
Fixes: 63978ab3e3 ("sound: add Edirol UA-101 support")
Cc: stable@vger.kernel.org
Signed-off-by: SeungJu Cheon <suunj1331@gmail.com>
Link: https://patch.msgid.link/20260426111239.103296-1-suunj1331@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device, just like the Playstation 5's DualSense, has a volume
that's too low, hid-playstation solves this by raising the minimum
volume on the device itself by sending an output report, third party PS5
controllers/accessories do not support this output report format, so we
apply a quirk to raise the minimum volume by 6dB.
Signed-off-by: Rosalie Wanders <rosalie@mailbox.org>
Link: https://patch.msgid.link/20260426025520.3985-2-rosalie@mailbox.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAC3 cluster descriptor length check in
snd_usb_get_audioformat_uac3()was added to
make sure that the buffer is large enough for
a struct uac3_cluster_header_descriptor before the
returned data is cast and used.
However, the check uses sizeof(cluster), where cluster
is a pointer, not the size of the descriptor header.
This makes the validation depend on the architecture
pointer size and does not match the intended object size.
Check against sizeof(*cluster) instead.
Fixes: fb4e2a6e8f ("ALSA: usb-audio: Fix out-of-bounds read in snd_usb_get_audioformat_uac3()")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260424-alsa-usb-uac3-cluster-size-v1-1-99a5808898a3@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_microii_spdif_switch_put() returns 0 when the requested
vendor register value differs from the cached one.
This comparison was inverted by the resume-support conversion,
so real SPDIF switch toggles are ignored while no-op writes still
issue SET_CUR and report success.
Return early only when the requested value matches the cached one.
Fixes: 288673beae ("ALSA: usb-audio: Add resume support for MicroII SPDIF ctls")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260421-microii-spdif-switch-fix-v1-1-5c50dc28b88f@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_emuusb_set_samplerate() unconditionally notifies the E-MU
SampleRate Extension Unit control after issuing SET_CUR.
If snd_usb_mixer_set_ctl_value() fails, the control value has not
changed, yet snd_usb_mixer_notify_id() still invalidates the cache and
emits a value-change event to userspace.
Notify the control only after a successful write.
Fixes: 7d2b451e65 ("ALSA: usb-audio - Added functionality for E-mu 0404USB/0202USB/TrackerPre")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260421-alsa-emuusb-samplerate-notify-v1-1-8b63bbc1d7f1@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
