ep93xx_i2s_enable() calls clk_prepare_enable() on three clocks in
sequence (mclk, sclk, lrclk) without checking the return value of any
of them. If an intermediate enable fails, the clocks that were already
enabled are never rolled back, leaking them until the next disable cycle
— which may never come if the stream never started cleanly.
Change ep93xx_i2s_enable() from void to int. Add error checking after
each clk_prepare_enable() call and unwind already-enabled clocks on
failure. Propagate the error through ep93xx_i2s_startup() and
ep93xx_i2s_resume(), both of which already return int.
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Fixes: f4ff6b56bc ("ASoC: cirrus: i2s: Prepare clock before using it")
Link: https://patch.msgid.link/20260324210909.45494-1-jihed.chaibi.dev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all drivers below sound/soc to use .remove(), with the eventual
goal to drop struct platform_driver::remove_new(). As .remove() and
.remove_new() have the same prototypes, conversion is done by just
changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20240909151230.909818-2-u.kleine-koenig@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-10-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Make startup/shutdown callbacks symmetric to avoid clock subsystem warnings
(reproduced with "aplay --dump-hw-params" + ctrl-c):
WARNING: CPU: 0 PID: 102 at drivers/clk/clk.c:1048 clk_core_disable
lrclk already disabled
CPU: 0 PID: 102 Comm: aplay Not tainted 6.2.0-rc4 #1
Hardware name: Generic DT based system
...
clk_core_disable from clk_core_disable_lock
clk_core_disable_lock from ep93xx_i2s_shutdown
ep93xx_i2s_shutdown from snd_soc_dai_shutdown
snd_soc_dai_shutdown from soc_pcm_clean
soc_pcm_clean from soc_pcm_close
soc_pcm_close from snd_pcm_release_substream.part.0
snd_pcm_release_substream.part.0 from snd_pcm_release
snd_pcm_release from __fput
__fput from task_work_run
...
WARNING: CPU: 0 PID: 102 at drivers/clk/clk.c:907 clk_core_unprepare
lrclk already unprepared
CPU: 0 PID: 102 Comm: aplay Tainted: G W 6.2.0-rc4 #1
Hardware name: Generic DT based system
...
clk_core_unprepare from clk_unprepare
clk_unprepare from ep93xx_i2s_shutdown
ep93xx_i2s_shutdown from snd_soc_dai_shutdown
snd_soc_dai_shutdown from soc_pcm_clean
soc_pcm_clean from soc_pcm_close
soc_pcm_close from snd_pcm_release_substream.part.0
snd_pcm_release_substream.part.0 from snd_pcm_release
snd_pcm_release from __fput
__fput from task_work_run
...
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230410223902.2321834-2-alexander.sverdlin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20230315150745.67084-42-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20230315150745.67084-41-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull sound updates from Takashi Iwai:
"The majority of works in this cycle are about ASoC spread over trees.
Most of them are for new devices and cleanups / refactoring works, and
not much significant changes are seen in the core side.
Below are some highlights:
ASoC:
- Continued refactoring to move into common helper functions
- Lots of DT schema conversons and stylistic nits
- Continued work on building out the new SOF IPC4 scheme
- Continued work for Intel AVS
- New drivers for Awinc AT88395, Infineon PEB2466, Iron Device
SMA1303, Mediatek MT8188, Realtek RT712, Renesas IDT821034,
Samsung/Tesla FSD SoC I2S, and TI TAS5720A-Q1
ALSA:
- A few cleanups to make the remove callbacks to void returns
- FireWire refactoring and enhancements
- PCM kselftest enhancements"
* tag 'sound-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (398 commits)
ALSA: hda/hdmi: Register with vga_switcheroo on Dual GPU Macbooks
ASoC: soc-ac97: Return correct error codes
ASoC: soc-dapm.h: fixup warning struct snd_pcm_substream not declared
ASoC: cs35l45: Remove separate namespace for tables
ASoC: cs35l45: Remove separate tables module
ASoC: soc-ac97: Convert to agnostic GPIO API
ASoC: dt-bindings: renesas,rsnd.yaml: drop "dmas/dma-names" from "rcar_sound,ssi"
ALSA: hda: cs35l41: Enable Amp High Pass Filter
ALSA: hda: cs35l41: Ensure firmware/tuning pairs are always loaded
ALSA: hda: cs35l41: Correct error condition handling
ASoC: codecs: wcd934x: Use min macro for comparison and assignment
ASoC: Intel: Skylake: Fix struct definition
ASoC: tlv320adcx140: extend list of supported samplerates
ASoC: imx-pcm-rpmsg: Remove unused variable
SoC: rt5682s: Disable jack detection interrupt during suspend
ASoC: SOF: Intel: hda-dsp: Set streaming flag for d0i3
ASoC: SOF: Intel: Enable d0i3 work for ipc4
ASoC: SOF: ipc4: Wake up dsp core before sending ipc msg
ASoC: SOF: Intel: hda-dsp: use set_pm_gate according to ipc version
ASoC: SOF: Introduce a new set_pm_gate() IPC PM op
...
Commit 2458adb8f9
("SoC: simple-card-utils: set 0Hz to sysclk when shutdown")
added a call to snd_soc_dai_set_sysclk() with 0 Hz frequency. Being
propagated further it causes a division by zero in clk-ep93xx driver:
Division by zero in kernel.
CPU: 0 PID: 52 Comm: aplay Tainted: G W 6.2.0-rc4-... #1
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x18
show_stack from dump_stack_lvl+0x28/0x34
dump_stack_lvl from __div0+0x10/0x1c
__div0 from Ldiv0+0x8/0x1c
Ldiv0 from ep93xx_mux_determine_rate+0x78/0x1d0
ep93xx_mux_determine_rate from clk_core_round_rate_nolock+0x48/0xc8
clk_core_round_rate_nolock from clk_core_set_rate_nolock+0x48/0x160
clk_core_set_rate_nolock from clk_set_rate+0x30/0x8c
clk_set_rate from ep93xx_i2s_set_sysclk+0x30/0x6c
ep93xx_i2s_set_sysclk from snd_soc_dai_set_sysclk+0x3c/0xa4
snd_soc_dai_set_sysclk from asoc_simple_shutdown+0xb8/0x164
asoc_simple_shutdown from snd_soc_link_shutdown+0x44/0x54
snd_soc_link_shutdown from soc_pcm_clean+0x78/0x180
soc_pcm_clean from soc_pcm_close+0x28/0x40
soc_pcm_close from snd_pcm_release_substream.part.0+0x3c/0x84
snd_pcm_release_substream.part.0 from snd_pcm_release+0x40/0x88
snd_pcm_release from __fput+0x74/0x278
There has been commit f1879d7b98 ("ASoC: rockchip: ignore 0Hz sysclk"),
but it prepared by far not all drivers.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230212220923.258414-1-alexander.sverdlin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of ep93xx board files were unused and got removed, so
the corresponding ASoC support can also be removed.
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Ryan Mallon <rmallon@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
Use clk_prepare_enable()/clk_disable_unprepare() in preparation for switch
to Common Clock Framework, otherwise the following is visible:
WARNING: CPU: 0 PID: 97 at drivers/clk/clk.c:1011 clk_core_enable+0x9c/0xbc
Enabling unprepared mclk
...
Hardware name: Cirrus Logic EDB9302 Evaluation Board
...
clk_core_enable
clk_core_enable_lock
ep93xx_i2s_hw_params
snd_soc_dai_hw_params
soc_pcm_hw_params
snd_pcm_hw_params
snd_pcm_ioctl
...
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211018103105.146380-2-alexander.sverdlin@gmail.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Jihed Chaibi
Kuninori Morimoto
Linus Torvalds
Alexander Sverdlin
Uwe Kleine-König
Takashi Iwai
Linus Walleij
Uwe Kleine-König
Arnd Bergmann
Charles Keepax
Mark Brown