The use of snprintf() may cause a warning with W=1 due to the possibly
truncated string. As the truncation doesn't really matter (and won't
happen practically) in the case of dice driver, just shut it up by
replacing with scnprintf().
Link: https://patch.msgid.link/20260227155705.1557224-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TEAC Corporation launched IF-FW/DM MkII as an add-in card for TASCAM
DM-3200 and DM-4800. This card uses TC Applied Technologies DICE II
ASIC.
This commit supports the add-in card. The configuration ROM content
includes some quirks:
- The category value stored in chip_ID_hi field of bus information block
is zero.
- The value of model in unit directory (0x00022e) is different from the
one in root directory (0x000006).
The hardware allows users to select the total number of audio data channels
available for system from 16 and 32 channels for both input and output
direction. In 16-channel mode, all audio data are transferred in a
single isochronous packet stream, while in 32-channel mode, they are
transferred across two streams. After the user changes the channel
configuration on the hardware panel, the device temporarily disappears
from the bus and reappears with the new stream formats. During device
probing the ALSA dice driver checks the number of available isochronous
packet streams to determine the active mode of the hardware.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://patch.msgid.link/20251017111145.263295-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the former commits, the callback of isochronous context runs on usual
work process. In the case, ALSA PCM device has a flag, nonatomic, to
acquire mutex lock instead of spin lock for PCM substream group.
This commit uses the flag. It has an advantage in the case that ALSA PCM
application uses the large size of intermediate buffer, since it takes
too long time even in tasklet softIRQ to process many of isochronous
packets, then result in the delay of system event due to disabled IRQ so
long. It is avertible to switch to nonatomic operation.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Edmund Raile <edmund.raile@protonmail.com>
Link: https://lore.kernel.org/r/20240904125155.461886-6-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Pull sound updates from Takashi Iwai:
"This looks like a relatively calm development cycle; there have been
only few changes in ALSA and ASoC core sides while we get lots of
device-specific fixes and updates as usual. Most of commits are about
ASoC, including Intel SOF/AVS and many device tree updates.
Below are some highlights:
Core:
- Improvement in memalloc helper for fallback allocations
- More cleanups of ASoC DAPM code
ASoC:
- Factoring out of mapping hw_params onto SoundWire configuration
- The ever ongoing overhauls of the Intel DSP code continue,
including support for loading libraries and probes with IPC4 on
SOF.
- Support for more sample formats on JZ4740
- Lots of device tree conversions and fixups
- Support for Allwinner D1, a range of AMD and Intel systems,
Mediatek systems with multiple DMICs, Nuvoton NAU8318, NXP
fsl_rpmsg and i.MX93, Qualcomm AudioReach Enable, MFC and SAL,
RealTek RT1318 and Rockchip RK3588
ALSA:
- Addition of PCM kselftest; still minimalistic but can be extended
in future
- Fixes for corner-case XRUNs with USB-audio implicit feedback mode
- Usual device-specific quirk updates for USB- and HD-audio
- FireWire DICE updates
This also contains a few cross-tree updates:
- Some OMAP board file updates for removal of relevant OMAP platforms
- A new I2C API update for I2C probe API adaption
- A DRM update for the further hdmi-codec updates"
* tag 'sound-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (417 commits)
ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt
ALSA: patch_realtek: Fix Dell Inspiron Plus 16
ALSA: hda/cirrus: Add extra 10 ms delay to allow PLL settle and lock.
ASoC: dt-bindings: Correct Alexandre Belloni email
ASoC: dt-bindings: maxim,max98504: Convert to DT schema
ASoC: dt-bindings: maxim,max98357a: Convert to DT schema
ASoC: dt-bindings: Reference common DAI properties
ASoC: dt-bindings: Extend name-prefix.yaml into common DAI properties
ASoC: rt715: Make read-only arrays capture_reg_H and capture_reg_L static const
ASoC: uniphier: aio-core: Make some read-only arrays static const
ASoC: wcd938x: Make read-only array minCode_param static const
ASoC: qcom: lpass-sc7280: Add maybe_unused tag for system PM ops
ASoC : SOF: amd: Add support for IPC and DSP dumps
ASoC: SOF: amd: Use poll function instead to read ACP_SHA_DSP_FW_QUALIFIER
ALSA: usb-audio: Workaround for XRUN at prepare
ALSA: pcm: Handle XRUN at trigger START
ALSA: pcm: Set missing stop_operating flag at undoing trigger start
drm: tda99x: Don't advertise non-existent capture support
ASoC: hdmi-codec: Allow playback and capture to be disabled
kselftest/alsa: Add more coverage of sample rates and channel counts
...
TC Applied Technologies (TCAT) produces TCD3070 as final DICE ASIC for
communication in IEEE 1394 bus for IEC 61883-1/6 protocol. As long as I
know, latter model of Focusrite Saffire Pro 40 is an application of the
ASIC and only in the market for consumers.
This patchset adds support for the device. The device has several
remarkable points.
1. No support for extended synchronization information section in TCAT
general protocol. The value of GLOBAL_EXTENDED_STATUS register is always
zero. Additionally, NOTIFY_EXT_STATUS message is never emitted.
2. No support for TCAT protocol extension. Hard coding is required for
format of CIP payload.
3. During several seconds after changing sampling rate, the block to
process PCM frames is under disfunction. When starting packet streaming
during the state, the block is never function till configuring different
sampling rate and several seconds.
This commit adds support for the device. The item 1 and 2 can be
adaptable, while item 3 is not. It's not preferable that user process
is forced to sleep during the disfunction in the call of ioctl(2) with
SNDRV_PCM_IOCTL_HW_PARAMS or SNDRV_PCM_IOCTL_PREPARE request. It's
inconvenient but let user configure preferable sampling rate in advance
of starting PCM substream.
The content of configuration ROM in the device I used is available at:
* https://github.com/takaswie/am-config-roms/
I note that any mixer control operation is implemented by unique
transaction. The frame of request consists of 16 bytes header followed
by payload.
header (4 quadlets):
1st: the type of request, prefixed with 0x8000
2nd: counter at 2 bytes in MSB side, the length of data at 2 bytes in LSB
side
3rd: parameter 0
4th: parameter 1
payload (variable length if need):
5th-: data according to parameters
The request frame is sent by block write request to 0x'ffff'e040'01c0.
The frame of response is similar to the frame of request, but it is
header only, thus fixed to 16 bytes. The response frame is sent to the
address which is registered by lock transaction to 0x'ffff'e040'0008.
If the operation results in batch of data, the 2nd quadlet of header
includes the length of data like request. The data is itself readable
by read block request to 0x'ffff'e040'0030, which includes both
header and payload for data, thus the length to read should be the
length of data plus 16 bytes for header
The actual value of request, parameter 0, parameter 1, and data is
unclear yet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20221130143313.43880-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Lexicon I-ONIX FW810S, the call of ioctl(2) with
SNDRV_PCM_IOCTL_HW_PARAMS can returns -ETIMEDOUT. This is a regression due
to the commit 41319eb56e ("ALSA: dice: wait just for
NOTIFY_CLOCK_ACCEPTED after GLOBAL_CLOCK_SELECT operation"). The device
does not emit NOTIFY_CLOCK_ACCEPTED notification when accepting
GLOBAL_CLOCK_SELECT operation with the same parameters as current ones.
This commit fixes the regression. When receiving no notification, return
-ETIMEDOUT as long as operating for any change.
Fixes: 41319eb56e ("ALSA: dice: wait just for NOTIFY_CLOCK_ACCEPTED after GLOBAL_CLOCK_SELECT operation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20221130130604.29774-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit takes ALSA dice driver to perform sequence replay for media
clock recovery.
Unlike the other types of device, DICE-based devices interpret the value
of syt field of CIP header in rx packets as presentation time for audio
playback, thus it's required for driver to compute value for outgoing
packet adequate to the device. It's done by media clock recovery by
handling tx packets.
The device starts packet transmission immediately at operation to
GLOBAL_ENABLE thus on-the-fly mode is not required.
DICE ASICs supports several pairs of isochronous packet streams.
Actually, maximum two pairs of streams are supported by devices.
We have three cases regarding to the number of streams:
1. a pair of streams
2. two tx packet streams and one rx packet streams
3. one tx packet streams and two rx packet streams
4. two pair of streams
The decision of playback timing is slightly different in the four cases.
In the case 1, sequence replay in the pair results in suitable playback
timing.
In the case 2, sequence replay from the first tx packet stream to rx
packet stream results in suitable playback timing.
In the case 3, sequence replay from tx packet stream to all of rx packet
stream results in suitable playback timing. Furthermore, the cycle to
start receiving packets should be the same between all rx packet streams.
In the case 4, sequence replay in each pair results in suitable playback
timing. Furthermore, the cycle to start receiving packets should be the
same between all rx packet streams.
The sequence replay is tested with below models:
* For case 1:
* TC Electronic Konnekt 24d (DiceII)
* TC Electronic Konnekt 8 (DiceII)
* TC Electronic Konnekt Live (DiceII)
* TC Electronic Impact Twin (DiceII)
* TC Electronic Digital Konnekt X32 (DiceII)
* TC Electronic Desktop Konnekt 6 (TCD2220)
* Solid State Logic Duende Classic (DiceII)
* Solid State Logic Duende Mini (DiceII)
* PreSonus FireStudio Project (TCD2210)
* PreSonus FireStudio Mobile (TCD2210)
* Lexicon I-ONIX FW810s (TCD2220)
* Avid Mbox 3 Pro (TCD2220)
* For case 2 (but case 1 depends on sampling transfer frequency):
* Alesis iO 26 (DiceII)
* Alesis iO 14 (DiceII)
* Alesis MultiMix 12 FireWire (DiceII)
* Focusrite Saffire Pro 26 (TCD2220)
* For case 3 (but case 1 depends on sampling transfer frequency):
* M-Audio Profire 610 (TCD2220)
* Loud Technology Mackie Onyx Blackbird (TCD2210)
* For case 4:
* TC Electronic Studio Konnekt 48 (DiceII + TCD2220)
* PreSonus FireStudio (DiceII)
* M-Audio Profire 2626 (TCD2220)
* Focusrite Liquid Saffire 56 (TCD2220)
* Focusrite Saffire Pro 40 (TCD2220)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210601081753.9191-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NOTIFY_CLOCK_ACCEPTED notification is always generated as a result of
GLOBAL_CLOCK_SELECT operation, however NOTIFY_LOCK_CHG notification
doesn't, as long as the selected clock is already configured. In the case,
ALSA dice driver waits so long. It's inconvenient for some devices to lock
to the sequence of value in syt field of CIP header in rx packets.
This commit wait just for NOTIFY_CLOCK_ACCEPTED notification by reverting
changes partially done by two commits below:
* commit fbeac84dbe ("ALSA: dice: old firmware optimization for Dice notification")
* commit aec045b80d ("ALSA: dice: change notification mask to detect lock status change")
I note that the successful lock to the sequence of value in syt field of
CIP header in rx packets results in NOTIFY_EXT_STATUS notification, then
EXT_STATUS_ARX1_LOCKED bit stands in GLOBAL_EXTENDED_STATUS register.
The notification can occur enough after receiving the batch of rx packets.
When the sequence doesn't include value in syt field of CIP header in rx
packets adequate to the device, the notification occurs again and the bit
is off.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210601081753.9191-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Models in below series start transmission of packet after receiving the
sequence of packets:
* Digidesign Digi00x family
* RME Fireface series
Additionally, models in Tascam FireWire series start multiplexing PCM
frames into packets enough after receiving packets. It's required to
transfer packets on-the-fly for the above models according to nominal
sampling transfer frequency before starting sequence replay.
This commit allows drivers to decide whether the engine transfers packet
on-the-fly or not.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210527122611.173711-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In design of audio and music unit in IEEE 1394 bus, feedback of
effective sampling transfer frequency (STF) is delivered by packets
transferred from device. The devices supported by ALSA firewire stack
are categorized to three groups regarding to it.
* Group 1:
* Echo Audio Fireworks board module
* Oxford Semiconductor OXFW971 ASIC
* Digidesign Digi00x family
* Tascam FireWire series
* RME Fireface series
* Group 2:
* BridgeCo. DM1000/DM1100/DM1500 ASICs for BeBoB solution
* TC Applied Technologies DICE ASICs
* Group 3:
* Mark of the Unicord FireWire series
In group 1, the effective STF is determined by the sequence of the number
of events per packet. In group 2, the sequence of presentation timestamp
expressed in syt field of CIP header is interpreted as well. In group 3,
the presentation timestamp is expressed in source packet header (SPH) of
each data block.
I note that some models doesn't take care of effective STF with large
internal buffer. It's reasonable to name it as group 0:
* Group 0
* Oxford Semiconductor OXFW970 ASIC
The effective STF is known to be slightly different from nominal STF for
all of devices, and to be different between the devices. Furthermore, the
effective STF is known to be shifted for long-period transmission. This
makes it hard for software to satisfy the effective STF when processing
packets to the device.
The effective STF is deterministic as a result of analyzing the batch of
packet transferred from the device. For the analysis, caching the sequence
of parameter in the packet is required.
This commit adds an option so that AMDTP domain structure takes AMDTP
stream structure to cache the sequence of parameters in packet transferred
from the device. The parameters are offset ticks of syt field against the
cycle to receive the packet and the number of data blocks per packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210527122611.173711-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When starting AMDTP domain, tasks in process context yields running CPU
till all of isochronous context get callback, with an assumption that
it's OK to process content of packet.
However several isochronous cycles are skipped to transfer rx packets, or
the content of rx packets are dropped, to manage the timing to start
processing the packets.
This commit changes the timing for tasks in process context to wake up
when processing content of packet is actually ready.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210520040154.80450-9-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
