Since commit a8bb74acd8 ("rcu: Consolidate RCU-sched update-side function definitions")
there is no difference between rcu_read_lock(), rcu_read_lock_bh() and
rcu_read_lock_sched() in terms of RCU read section and the relevant grace
period. That means that spin_lock(), which implies rcu_read_lock_sched(),
also implies rcu_read_lock().
There is no need no explicitly start a RCU read section if one has already
been started implicitly by spin_lock().
Simplify the code and remove the inner rcu_read_lock() invocation.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: pengdonglin <pengdonglin@xiaomi.com>
Signed-off-by: pengdonglin <dolinux.peng@gmail.com>
Link: https://patch.msgid.link/20250916044735.2316171-11-dolinux.peng@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful for multi-radio devices that are capable of monitoring on
multiple channels simultanenously. When this flag is set, each monitor
interface is passed to the driver individually and can have a configured
channel.
The vif mac address for non-active monitor interfaces is cleared, in order
to allow the driver to tell them apart from active ones.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://patch.msgid.link/3c55505ee0cf0a5f141fbcb30d1e8be8d9f40373.1728462320.git-series.nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This flag is annoying because it puts a lot of logic into mac80211
that could just as well be in the driver (only iwlmvm uses it) and
the implementation is also broken for MLO.
Remove the flag in favour of calling drv_mgd_prepare_tx() without
any conditions even for the deauth-while-assoc case. The drivers
that implement it can take the appropriate actions, which for the
only user of DEAUTH_NEED_MGD_TX_PREP (iwlmvm) is a bit more tricky
than the implementation in mac80211 is anyway, and all others have
no need and can just exit if info->was_assoc is set.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240627132527.94924bcc9c9e.I328a219e45f2e2724cd52e75bb9feee3bf21a463@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When doing CSA in multi-link, there really isn't a need to
stop transmissions entirely. Add a feature flag for drivers
to indicate they can handle quiet in CSA (be it by parsing
themselves, or by implementing drv_pre_channel_switch()),
to make that possible.
Also clean up the csa_block_tx handling: it clearly cannot
handle multi-link due to the way queues are stopped, move
it to the sdata. Drivers should be doing it themselves for
working properly during CSA in MLO anyway. Also rename it
to indicate that it reflects TX was blocked at mac80211.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095719.258439191541.I2469d206e2bf5cb244cfde2b4bbc2ae6d1cd3dd9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the sta_mtx, so we don't need this mutex any
more. Remove it.
Most of this change was done automatically with spatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we no longer really use the RTNL, there's no point
in locking it here. Most drivers don't really need to
have any locks here anyway, and the rest are probably
completely broken, but it's a debugfs-only callback so
it really doesn't matter much.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All drivers are now using mac80211 internal queues (iTXQs).
Drop mac80211 internal support for the old push path.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For drivers using software encryption for multicast TX, such
as mac80211_hwsim, mac80211 needs to duplicate the multicast
frames on each link, if MLO is enabled. Do this, but don't
just make it dependent on the key but provide a separate flag
for drivers to opt out of this.
This is not very efficient, I expect that drivers will do it
in firmware/hardware or at least with DMA engine assistence,
so this is mostly for hwsim.
To make this work, also implement the SNS11 sequence number
space that an AP MLD shall have, and modify the API to the
__ieee80211_subif_start_xmit() function to always require the
link ID bits to be set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commits 6a789ba679 and
2433647bc8.
The virtual time scheduler code has a number of issues:
- queues slowed down by hardware/firmware powersave handling were not properly
handled.
- on ath10k in push-pull mode, tx queues that the driver tries to pull from
were starved, causing excessive latency
- delay between tx enqueue and reported airtime use were causing excessively
bursty tx behavior
The bursty behavior may also be present on the round-robin scheduler, but there
it is much easier to fix without introducing additional regressions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This switches the airtime scheduler in mac80211 to use a virtual
time-based scheduler instead of the round-robin scheduler used before.
This has a couple of advantages:
- No need to sync up the round-robin scheduler in firmware/hardware with
the round-robin airtime scheduler.
- If several stations are eligible for transmission we can schedule both
of them; no need to hard-block the scheduling rotation until the head
of the queue has used up its quantum.
- The check of whether a station is eligible for transmission becomes
simpler (in ieee80211_txq_may_transmit()).
The drawback is that scheduling becomes slightly more expensive, as we
need to maintain an rbtree of TXQs sorted by virtual time. This means
that ieee80211_register_airtime() becomes O(logN) in the number of
currently scheduled TXQs because it can change the order of the
scheduled stations. We mitigate this overhead by only resorting when a
station changes position in the tree, and hopefully N rarely grows too
big (it's only TXQs currently backlogged, not all associated stations),
so it shouldn't be too big of an issue.
To prevent divisions in the fast path, we maintain both station sums and
pre-computed reciprocals of the sums. This turns the fast-path operation
into a multiplication, with divisions only happening as the number of
active stations change (to re-compute the current sum of all active
station weights). To prevent this re-computation of the reciprocal from
happening too frequently, we use a time-based notion of station
activity, instead of updating the weight every time a station gets
scheduled or de-scheduled. As queues can oscillate between empty and
occupied quite frequently, this can significantly cut down on the number
of re-computations. It also has the added benefit of making the station
airtime calculation independent on whether the queue happened to have
drained at the time an airtime value was accounted.
Co-developed-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210623134755.235545-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jakub Kicinski
Kuniyuki IwashimaandJohannes Berg
Ria ThomasandJohannes Berg
Sarika SharmaandJohannes Berg
pengdonglinandJohannes Berg
Felix FietkauandJohannes Berg
Yingsha XuandJohannes Berg
Alexander WetzelandJohannes Berg
Lorenzo BianconiandJohannes Berg
Toke Høiland-JørgensenandJohannes Berg