The GCE in MT8196 is placed in MMINFRA and requires all addresses
in GCE instructions for DRAM transactions to be IOVA.
Due to MMIO, if the GCE needs to access a hardware register at
0x1000_0000, but the SMMU is also mapping a DRAM block at 0x1000_0000,
the MMINFRA will not know whether to write to the hardware register or
the DRAM.
To solve this, MMINFRA treats addresses greater than 2G as data paths
and those less than 2G as config paths because the DRAM start address
is currently at 2G (0x8000_0000). On the data path, MMINFRA remaps
DRAM addresses by subtracting 2G, allowing SMMU to map DRAM addresses
less than 2G.
For example, if the DRAM start address 0x8000_0000 is mapped to
IOVA=0x0, when GCE accesses IOVA=0x0, it must add a 2G offset to
the address in the GCE instruction. MMINFRA will then see it as a
data path (IOVA >= 2G) and subtract 2G, allowing GCE to access IOVA=0x0.
Since the MMINFRA remap subtracting 2G is done in hardware and cannot
be configured by software, the address of DRAM in GCE instruction must
always add 2G to ensure proper access. After that, the shift functions
do more than just shift addresses, so the APIs were renamed to
cmdq_convert_gce_addr() and cmdq_revert_gce_addr().
This 2G adjustment is referred to as mminfra_offset in the CMDQ driver.
CMDQ helper can get the mminfra_offset from the cmdq_mbox_priv of
cmdq_pkt and add the mminfra_offset to the DRAM address in GCE
instructions.
Signed-off-by: Jason-JH Lin <jason-jh.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Add the cmdq_mbox_priv structure to store the private data of GCE,
such as the shift bits of the physical address. Then, include the
cmdq_mbox_priv structure within the cmdq_pkt structure.
This allows CMDQ users to utilize the private data in cmdq_pkt to
generate GCE instructions when needed. Additionally, having
cmdq_mbox_priv makes it easier to expand and reference other GCE
private data in the future.
Add cmdq_get_mbox_priv() for CMDQ users to get all the private data
into the cmdq_mbox_priv of the cmdq_pkt.
Signed-off-by: Jason-JH Lin <jason-jh.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
GCE can only fetch the command buffer address from a 32-bit register.
Some SoCs support a 35-bit command buffer address for GCE, which
requires a right shift of 3 bits before setting the address into
the 32-bit register. A comment has been added to the header of
cmdq_get_shift_pa() to explain this requirement.
To prevent the GCE command buffer address from being DMA mapped beyond
its supported bit range, the DMA bit mask for the device is set during
initialization.
Additionally, to ensure the correct shift is applied when setting or
reading the register that stores the GCE command buffer address,
new APIs, cmdq_convert_gce_addr() and cmdq_revert_gce_addr(), have
been introduced for consistent operations on this register.
The variable type for the command buffer address has been standardized
to dma_addr_t to prevent handling issues caused by type mismatches.
Fixes: 0858fde496 ("mailbox: cmdq: variablize address shift in platform")
Signed-off-by: Jason-JH Lin <jason-jh.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
The RPMI specification defines a system MSI service group which
allows application processors to receive MSIs upon system events
such as graceful shutdown/reboot request, CPU hotplug event, memory
hotplug event, etc.
Add an irqchip driver for the RISC-V RPMI system MSI service group
to directly receive system MSIs in Linux kernel.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Link: https://lore.kernel.org/r/20250818040920.272664-14-apatel@ventanamicro.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
Every client driver has the struct cmdq_client information, so
it's not necessary to store it in struct cmdq_pkt. cl is used to
store struct cmdq_client information and now no client driver use
it, so remove it.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
The Samsung Exynos mailbox controller, used on Google GS101 SoC, has 16
flag bits for hardware interrupt generation and a shared register for
passing mailbox messages. When the controller is used by the
ACPM interface the shared register is ignored and the mailbox controller
acts as a doorbell. The controller just raises the interrupt to APM
after the ACPM interface has written the message to SRAM.
Add support for the Samsung Exynos mailbox controller.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Add a mailbox controller driver for the Microchip Inter-processor
Communication (IPC), which is used to send and receive data between
processors.
The driver uses the RISC-V Supervisor Binary Interface (SBI) to
communicate with software running in machine mode (M-mode) to access
the IPC hardware block.
Additional details on the Microchip vendor extension and the IPC
function IDs described in the driver can be found in the following
documentation:
https://github.com/linux4microchip/microchip-sbi-ecall-extension
This SBI interface in this driver is compatible with the Mi-V Inter-hart
Communication (IHC) IP.
Transmitting and receiving data through the mailbox framework is done
through struct mchp_ipc_msg.
Signed-off-by: Valentina Fernandez <valentina.fernandezalanis@microchip.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
rx_callback is a standard mailbox callback mechanism and could cover the
function of proprietary cmdq_task_cb, so use the standard one instead of
the proprietary one. Client driver has changed to use standard
rx_callback, so remove proprietary cmdq_task_cb.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Current client use 'struct cmdq_pkt' as callback data, so
change 'void *data' to 'struct cmdq_pkt *pkt'. Keep data
until client use pkt instead of data.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This adds driver for the ARM MHUv2 (Message Handling Unit) mailbox
controller.
This is based on the accepted DT bindings of the controller and supports
combination of both transport protocols, i.e. doorbell and data-transfer.
Transmitting and receiving data through the mailbox framework is done
through struct arm_mhuv2_mbox_msg.
Based on the initial work done by Morten Borup Petersen from ARM.
Co-developed-by: Tushar Khandelwal <tushar.khandelwal@arm.com>
Signed-off-by: Tushar Khandelwal <tushar.khandelwal@arm.com>
Tested-by: Usama Arif <usama.arif@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Some gce hardware shift pc and end address in register to support
large dram addressing.
Implement gce address shift when write or read pc and end register.
And add shift bit in platform definition.
Signed-off-by: Dennis YC Hsieh <dennis-yc.hsieh@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Jason-JH Lin
Jjian Zhou
Anup Patel
Rahul Pathak
Chun-Kuang Hu
Tudor Ambarus
Valentina Fernandez
Tanmay Shah
Viresh Kumar
Gustavo A. R. Silva
Dennis YC Hsieh
Linus Torvalds
Bibby Hsieh