The hdmi_colorspace enum was defined to represent the colorspace value
of the HDMI infoframes. It was later used by some HDMI drivers to
express the output format they should be setting up.
During the introduction of the HDMI helpers, it then was used to
represent it in the drm_connector_hdmi_state structure.
However, it's always been somewhat redundant with the DRM_COLOR_FORMAT_*
defines, and now with the drm_output_color_format enum. Let's
consolidate around drm_output_color_format in drm_connector_hdmi_state
to facilitate the current effort to provide a global output format
selection mechanism.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260305-drm-rework-color-formats-v3-14-f3935f6db579@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
of_drm_find_bridge() is deprecated. Move to its replacement
of_drm_find_and_get_bridge() which gets a bridge reference, and ensure it
is put when done. Also switch to the drm_bridge::next_bridge pointer.
This needs to handle both cases: when of_drm_find_panel() succeeds and when
it fails.
In the 'else' case (i.e. when of_drm_find_panel() fails), just switch to
of_drm_find_and_get_bridge() to ensure the bridge is not freed while in use
in the function tail, when it is stored in dsi->bridge.next_bridge.
In the 'then' case (i.e. when of_drm_find_panel() succeeds),
devm_drm_panel_bridge_add() already increments the refcount using devres
which ties the bridge allocation lifetime to the device lifetime, so we
would not need to do anything. However to have the same behaviour in both
branches take an additional reference here, so that the bridge needs to be
put whichever branch is taken without more complicated logic. Ensure to
clear the bridge pointer however, to avoid calling drm_bridge_put() on an
ERR_PTR.
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://patch.msgid.link/20260109-drm-bridge-alloc-getput-drm_of_find_bridge-2-v2-12-8bad3ef90b9f@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
After resume from suspend to RAM, the following splash is generated if
the HDMI driver is probed (independent of a connected cable):
[ 1194.484052] irq 80: nobody cared (try booting with the "irqpoll" option)
[ 1194.484074] CPU: 0 UID: 0 PID: 627 Comm: rtcwake Not tainted 6.17.0-rc7-g96f1a11414b3 #1 PREEMPT
[ 1194.484082] Hardware name: Rockchip RK3576 EVB V10 Board (DT)
[ 1194.484085] Call trace:
[ 1194.484087] ... (stripped)
[ 1194.484283] handlers:
[ 1194.484285] [<00000000bc363dcb>] dw_hdmi_qp_main_hardirq [dw_hdmi_qp]
[ 1194.484302] Disabling IRQ #80
Apparently the HDMI IP is losing part of its state while the system
is suspended and generates spurious interrupts during resume. The
bug has not yet been noticed, as system suspend does not yet work
properly on upstream kernel with either the Rockchip RK3588 or RK3576
platform.
Fixes: 128a9bf8ac ("drm/rockchip: Add basic RK3588 HDMI output support")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251014-rockchip-hdmi-suspend-fix-v1-1-983fcbf44839@collabora.com
Currently the TIMER_BASE_CONFIG0 register gets initialized to a fixed
value as initially found in vendor driver code supporting the RK3588
SoC. As a matter of fact the value matches the rate of the HDMI TX
reference clock, which is roughly 428.57 MHz.
However, on RK3576 SoC that rate is slightly lower, i.e. 396.00 MHz, and
the incorrect register configuration breaks CEC functionality.
Set the timer base according to the actual reference clock rate that
shall be provided by the platform driver. Otherwise fallback to the
vendor default.
While at it, also drop the unnecessary empty lines in
dw_hdmi_qp_init_hw().
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250903-rk3588-hdmi-cec-v4-2-fa25163c4b08@collabora.com
The HDMI TX Parallel Audio Interface (HTX_PAI) is a digital module that
acts as the bridge between the Audio Subsystem to the HDMI TX Controller.
This IP block is found in the HDMI subsystem of the i.MX8MP SoC.
Data received from the audio subsystem can have an arbitrary component
ordering. The HTX_PAI block has integrated muxing options to select which
sections of the 32-bit input data word will be mapped to each IEC60958
field. The HTX_PAI_FIELD_CTRL register contains mux selects to
individually select P,C,U,V,Data, and Preamble.
Use component helper so that imx8mp-hdmi-tx will be aggregate driver,
imx8mp-hdmi-pai will be component driver, then imx8mp-hdmi-pai can use
bind() ops to get the plat_data from imx8mp-hdmi-tx device.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20250923053001.2678596-6-shengjiu.wang@nxp.com
Add support for Exynos7870's DSIM IP block in the bridge driver.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Presently, all devices refer to clock names from a single array. The
only controlling parameter is the number of clocks (num_clks field of
samsung_dsim_driver_data) which uses the first n clocks of that array.
As new devices are added, this approach turns out to be cumbersome.
Separate the clock names in individual arrays required by each variant,
in a struct clk_bulk_data. Add a pointer field to the driver data struct
which points to their respective clock names, and rework the clock usage
code to use the clk_bulk_* API instead.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The PLL_STABLE bit of DSIM_DPHY_STATUS is hardcoded to BIT(31), but
Exynos7870's DSIM has it in BIT(24) as per downstream kernel sources.
In order to support both, move this bit value to the driver data struct
and define it for every driver compatible. Reference the value from
there instead, in functions wherever required.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Currently, PLL_P offset of DSIM_PLLCTRL is configurable in the driver
data, while PLL_M and PLL_S offsets are hardcoded as 4-bit and 1-bit
offsets respectively, but Exynos7870's DSIM have them at 3-bit and 0-bit
offsets as per downstream kernel sources.
In order to support both, move both offset values to the driver data
struct and define it for every driver compatible. Reference the values
from there instead, in functions wherever required.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The VIDEO_MODE bit of DSIM_CONFIG is hardcoded to BIT(25), but
Exynos7870's DSIM has it in BIT(18) as per downstream kernel sources.
In order to support both, move this bit value to the driver data struct
and define it for every driver compatible. Reference the value from
there instead, in functions wherever required.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The MAIN_VSA offset of DSIM_MSYNC is hardcoded to a 22-bit offset, but
Exynos7870's DSIM has it in a 16-bit offset as per the downstream kernel
sources.
In order to support both, move this offset value to the driver data
struct and define it for every driver compatible. Reference the value
from there instead, in functions wherever required.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DSIM_CLKCTRL bit and offset values hardcoded in the driver:
name | bit/offset value
--------------------------+-----------------
DSIM_LANE_ESC_CLK_EN_CLK | 19
DSIM_LANE_ESC_CLK_EN_DATA | 20
DSIM_BYTE_CLKEN | 24
DSIM_ESC_CLKEN | 28
DSIM_TX_REQUEST_HSCLK | 31
DSIM_CLKCTRL bit and offset values in Exynos7870 DSIM as per downstream
kernel sources:
name | bit/offset value
--------------------------+-----------------
DSIM_LANE_ESC_CLK_EN_CLK | 8
DSIM_LANE_ESC_CLK_EN_DATA | 9
DSIM_BYTE_CLKEN | 17
DSIM_ESC_CLKEN | 16
DSIM_TX_REQUEST_HSCLK | 20
In order to support both, move all values to the driver data struct and
define it for every driver compatible. Reference the values from there
instead, in functions wherever required.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos7870's DSIM device doesn't require waiting for the header FIFO
during a MIPI DSI transfer. Add a flag in the driver data in order to
control said behavior.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com
On Exynos7870 devices, enabling the display requires disabling
standby by writing to the SFRCTRL register. Add the register and related
bit values. Since this behavior isn't available on other SoCs, implement
a flag in the driver data struct indicating the availability of this
feature.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos7870's DSIM has separate registers for LINK and DPHY status. This
is in contrast to older variants in the driver which use a single
register for both.
Add a driver data flag which indicates that the device variant supports
the legacy status register. Change the register read calls
appropriately.
Suggested-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The DW DP TX Controller is compliant with the DisplayPort Specification
Version 1.4 with the following features:
* DisplayPort 1.4a
* Main Link: 1/2/4 lanes
* Main Link Support 1.62Gbps, 2.7Gbps, 5.4Gbps and 8.1Gbps
* AUX channel 1Mbps
* Single Stream Transport(SST)
* Multistream Transport (MST)
* Type-C support (alternate mode)
* HDCP 2.2, HDCP 1.3
* Supports up to 8/10 bits per color component
* Supports RBG, YCbCr4:4:4, YCbCr4:2:2, YCbCr4:2:0
* Pixel clock up to 594MHz
* I2S, SPDIF audio interface
Add library with common helpers to make it can be shared with
other SoC.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250822063959.692098-3-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
