Passing IRQF_ONESHOT ensures that the interrupt source is masked until
the secondary (threaded) handler is done. If only a primary handler is
used then the flag makes no sense because the interrupt can not fire
(again) while its handler is running.
The flag also prevents force-threading of the primary handler and the
irq-core will warn about this.
The intention here was probably to not allow forced-threading.
Replace IRQF_ONESHOT with IRQF_NO_THREAD.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-14-bigeasy@linutronix.de
Certain TEMP_ALARM GEN2 PMIC peripherals need over-temperature stage 2
automatic PMIC partial shutdown. This will ensure that in the event of
reaching the hotter stage 3 over-temperature threshold, repeated faults
will be avoided during the automatic PMIC hardware full shutdown.
Modify the stage 2 shutdown control logic to ensure that stage 2
shutdown is enabled on all affected PMICs. Read the digital major
and minor revision registers to identify these PMICs.
Signed-off-by: David Collins <david.collins@oss.qualcomm.com>
Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250710224555.3047790-2-anjelique.melendez@oss.qualcomm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Pull thermal control updates from Rafael Wysocki:
"These add support for a new feature, Platform Temperature Control
(PTC), to the Intel int340x thermal driver, add support for the Airoha
EN7581 thermal sensor and the IPQ5018 platform, fix up the ACPI
thermal zones handling, fix other assorted issues and clean up code
Specifics:
- Add Platform Temperature Control (PTC) support to the Intel int340x
thermal driver (Srinivas Pandruvada)
- Make the Hisilicon thermal driver compile by default when ARCH_HISI
is set (Krzysztof Kozlowski)
- Clean up printk() format by using %pC instead of %pCn in the
bcm2835 thermal driver (Luca Ceresoli)
- Fix variable name coding style in the AmLogic thermal driver
(Enrique Isidoro Vazquez Ramos)
- Fix missing debugfs entry removal on failure by using the devm_
variant in the LVTS thermal driver (AngeloGioacchino Del Regno)
- Remove the unused lvts_debugfs_exit() function as the devm_ variant
introduced before takes care of removing the debugfs entry in the
LVTS driver (Arnd Bergmann)
- Add the Airoha EN7581 thermal sensor support along with its DT
bindings (Christian Marangi)
- Add ipq5018 compatible string DT binding, cleanup and add its
suppot to the QCom Tsens thermal driver (Sricharan Ramabadhran,
George Moussalem)
- Fix comments typos in the Airoha driver (Christian Marangi, Colin
Ian King)
- Address a sparse warning by making a local variable static in the
QCom thermal driver (George Moussalem)
- Fix the usage of the _SCP control method in the driver for ACPI
thermal zones (Armin Wolf)"
* tag 'thermal-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: qcom: ipq5018: make ops_ipq5018 struct static
thermal/drivers/airoha: Fix spelling mistake "calibrarion" -> "calibration"
ACPI: thermal: Execute _SCP before reading trip points
ACPI: OSI: Stop advertising support for "3.0 _SCP Extensions"
thermal/drivers/airoha: Fix spelling mistake
thermal/drivers/qcom/tsens: Add support for IPQ5018 tsens
thermal/drivers/qcom/tsens: Add support for tsens v1 without RPM
thermal/drivers/qcom/tsens: Update conditions to strictly evaluate for IP v2+
dt-bindings: thermal: qcom-tsens: Add ipq5018 compatible
thermal/drivers: Add support for Airoha EN7581 thermal sensor
dt-bindings: thermal: Add support for Airoha EN7581 thermal sensor
thermal/drivers/mediatek/lvts: Remove unused lvts_debugfs_exit
thermal/drivers/mediatek/lvts: Fix debugfs unregister on failure
thermal/drivers/amlogic: Rename Uptat to uptat to follow kernel coding style
vsprintf: remove redundant and unused %pCn format specifier
thermal/drivers/bcm2835: Use %pC instead of %pCn
thermal/drivers/hisi: Do not enable by default during compile testing
thermal: int340x: processor_thermal: Platform temperature control documentation
thermal: intel: int340x: Enable platform temperature control
thermal: intel: int340x: Add platform temperature control interface
irq_domain_add_linear() is going away as being obsolete now. Switch to
the preferred irq_domain_create_linear(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fixed up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-39-jirislaby@kernel.org
SoCs without RPM need to enable sensors and calibrate them from the kernel.
The IPQ5332 and IPQ5424 use the tsens v2.3.3 IP and do not have RPM.
Therefore, add a new calibration function for V2, as the tsens.c calib
function only supports V1. Also add new feature_config, ops and data for
IPQ5332, IPQ5424.
Although the TSENS IP supports 16 sensors, not all are used. The hw_id
is used to enable the relevant sensors.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20250210120436.821684-3-quic_mmanikan@quicinc.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/thermal to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
On the way make a few whitespace changes to make indention consistent.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241019163412.304422-2-u.kleine-koenig@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Modify qpnp_tm_init() to use thermal_zone_get_crit_temp() to get the
critical trip temperature instead of iterating over trip indices and
using thermal_zone_get_trip() to get a struct thermal_trip pointer
from a trip index until it finds the critical one.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/7712228.EvYhyI6sBW@rjwysocki.net
Merge updates related to the thermal core for 6.11-rc1:
- Redesign the .set_trip_temp() thermal zone callback to take a trip
pointer instead of a trip ID and update its users (Rafael Wysocki).
- Avoid using invalid combinations of polling_delay and passive_delay
thermal zone parameters (Rafael Wysocki).
- Update a cooling device registration function to take a const
argument (Krzysztof Kozlowski).
- Make the uniphier thermal driver use thermal_zone_for_each_trip() for
walking trip points (Rafael Wysocki).
* thermal-core:
thermal: core: Add sanity checks for polling_delay and passive_delay
thermal: trip: Fold __thermal_zone_get_trip() into its caller
thermal: trip: Pass trip pointer to .set_trip_temp() thermal zone callback
thermal: imx: Drop critical trip check from imx_set_trip_temp()
thermal: trip: Add conversion macros for thermal trip priv field
thermal: helpers: Introduce thermal_trip_is_bound_to_cdev()
thermal: core: Change passive_delay and polling_delay data type
thermal: core: constify 'type' in devm_thermal_of_cooling_device_register()
thermal: uniphier: Use thermal_zone_for_each_trip() for walking trip points
