The argument variable is assigned the return value of
pinconf_to_config_argument(), which returns a u32. Change its type from
enum pin_config_param to unsigned int to correctly store the configuration
argument.
Fixes: 03b054e969 ("pinctrl: Pass all configs to driver on pin_config_set()")
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Pull pin control updates from Linus Walleij:
"We have GPIO awareness in the pin control core and an interesting
AAEON driver.
Core changes:
- Allow pins to be identified/marked as GPIO mode with a special
callback.
The pin controller core is now "aware" if a pin is in GPIO mode if
the callback is implemented in the driver, and can thus be marked
as "strict", i.e. disallowing simultaneous use of a line as GPIO
and another function such as I2C.
This is enabled in the Qualcomm TLMM driver and also implemeted
from day 1 in the new Broadcom STB driver
- Rename the pin config option PIN_CONFIG_OUTPUT to PIN_CONFIG_LEVEL
to better describe what the config is doing, as well as making it
more intuitive what shall be returned when reading this property
New drivers:
- Qualcomm SDM660 LPASS LPI TLMM pin controller subdriver
- Qualcomm Glymur family pin controller driver
- Broadcom STB family pin controller driver
- Tegra186 pin controller driver
- AAEON UP pin controller support.
This is some special pin controller that works as an external
advanced line MUX and amplifier for signals from an Intel SoC. A
cooperative effort with the GPIO maintainer was needed to reach a
solution where we reuse code from the GPIO aggregator/forwarder
driver
- Renesas RZ/T2H and RZ/N2H pin controller support
- Axis ARTPEC-8 subdriver for the Samsung pin controller driver
Improvements:
- Output enable (OEN) support in the Renesas RZG2L driver
- Properly support bias pull up/down in the pinctrl-single driver
- Move over all GPIO portions using generic MMIO GPIO to the new
generic GPIO chip management which has a nice and separate API
- Proper DT bindings for some older Broadcom SoCs
- External GPIO (EGPIO) support in the Qualcomm SM8250
Deleted code:
- Dropped the now unused Samsung S3C24xx drivers"
* tag 'pinctrl-v6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: use more common syntax for compound literals
pinctrl: Simplify printks with pOF format
pinctrl: qcom: Add SDM660 LPASS LPI TLMM
dt-bindings: pinctrl: qcom: Add SDM660 LPI pinctrl
pinctrl: qcom: lpass-lpi: Add ability to use custom pin offsets
pinctrl: qcom: Add glymur pinctrl driver
dt-bindings: pinctrl: qcom: Add Glymur pinctrl
pinctrl: qcom: sm8250: Add egpio support
pinctrl: generic: rename PIN_CONFIG_OUTPUT to LEVEL
pinctrl: keembay: fix double free in keembay_build_functions()
pinctrl: spacemit: fix typo in PRI_TDI pin name
pinctrl: eswin: Fix regulator error check and Kconfig dependency
pinctrl: bcm: Add STB family pin controller driver
dt-bindings: pinctrl: Add support for Broadcom STB pin controller
pinctrl: qcom: make the pinmuxing strict
pinctrl: qcom: mark the `gpio` and `egpio` pins function as non-strict functions
pinctrl: qcom: add infrastructure for marking pin functions as GPIOs
pinctrl: allow to mark pin functions as requestable GPIOs
pinctrl: qcom: use generic pin function helpers
pinctrl: make struct pinfunction a pointer in struct function_desc
...
This generic pin config property is confusingly named so let's
rename it to make things clearer.
There are already drivers in the tree that use PIN_CONFIG_OUTPUT
to *read* the value of an output driven pin, which is a big
semantic confusion for the head: are we then reading the
setting of the output or the actual value/level that is put
out on the pin?
We already have PIN_CONFIG_OUTPUT_ENABLE that turns on driver
buffers for output, so this can by logical conclusion only
drive the voltage level if it should be any different.
But if we read the pin, are we then reading the *setting* of
the output value or the *actual* value we can see on the
line?
If the pin has not first been set into output mode with
PIN_CONFIG_OUTPUT_ENABLE, but is instead in some input mode
or tristate, what will reading this property actually
return?
Reading the current users reading this property it is clear
that what we read is the logical level of the pin as 0 or 1
depending on if it is low or high.
Rename it to PIN_CONFIG_LEVEL so it is crystal clear that
we set or read the voltage level of the pin and nothing else.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/pinctrl to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/20241007205803.444994-8-u.kleine-koenig@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We create a custom compatible for the STA2X11 IP block as integrated
into the Mobileye EyeQ5 platform. Its wake and alternate functions have
been disabled, we want to avoid touching those registers.
We both do: (1) early return in functions that do not support the
platform, but with warnings, and (2) avoid calling those functions in
the first place.
We ensure that pinctrl-nomadik is not used with this STA2X11 variant.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-24-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move away from statically allocated GPIO IDs. Switch to dynamic ID
allocation. Static IDs are deprecated because they cause issues when
multiple GPIO controllers are to be found on the same platform.
Add a bit of complexity to do pin number -> GPIO chip + offset.
Previously, bank number and offsets were retrieved using division and
remainder (bank size being constant 32). Now, to get the pin number
matching a bank base, we must know the sum of ngpios of previous banks.
This is done in find_nmk_gpio_from_pin() which also exposes the offset
inside the bank.
Also remove the assumption that bank sizes are constant. Instead of
using NMK_GPIO_PER_CHIP as bank size, use nmk_gpio_chips[i]->ngpio.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-19-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix strict checkpatch warnings relative to if-else blocks and bool
expressions. Message types addressed:
CHECK: Comparison to NULL could be written "!nmk_cfg_params[index].choice"
CHECK: Unbalanced braces around else statement
CHECK: Using comparison to false is error prone
CHECK: Using comparison to true is error prone
CHECK: braces {} should be used on all arms of this statement
Before: 0 errors, 1 warnings, 16 checks.
After: 0 errors, 1 warnings, 7 checks.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-13-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
nmk_pinctrl_probe() iterates over each GPIO block. Use an early
conditional continue to skip to the next iteration rather than indent
all the loop code block.
Do not change code logic. The block is changed from:
for (i = 0; i < NMK_MAX_BANKS; i++) {
x = of_parse_phandle(...);
if (x) {
... do work ...
}
}
To:
for (i = 0; i < NMK_MAX_BANKS; i++) {
x = of_parse_phandle(...);
if (!x)
continue;
... do work ...
}
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-10-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
