Some pinctrl devices like mt6397 or mt6392 don't support EINT at all, but
the mtk_eint_init function is always called and returns -ENODEV, which
then bubbles up and causes probe failure.
To address this only call mtk_eint_init if EINT pins are present.
Tested on Xiaomi Mi Smart Clock x04g (mt6392).
Fixes: e46df235b4 ("pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit")
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The 'drv_offset' member in 'struct mtk_pinctrl_devdata' has been unused
since the driver's inception. Drive strength control for MediaTek
pinctrl drivers is actually configured via 'pin_drv_grp',
making this specific offset field redundant.
Remove the unused field from the common 'mtk_pinctrl_devdata' structure
and its corresponding initialization in the mt8365 driver to clean up
the code and avoid confusion.
Signed-off-by: Akari Tsuyukusa <akkun11.open@gmail.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The MT798x series SoCs have IES regiter definitions. I think we
must enable the ies_present flag to correctly configure the pin
input mode.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
mtk_eint_do_init() allocates several pointer arrays which are then
populated in a per-instance loop and freed on error. The arrays are
currently allocated with devm_kmalloc(), so their entries are left
uninitialised until the per-instance allocations succeed.
On a failure in the middle of the loop, the error path iterates over
the full nbase range and calls devm_kfree() on each element. For
indices which were never initialised, the corresponding array entries
contain stack garbage. If any of those happen to be non-zero,
devm_kfree() will pass them to devres_destroy(), which will WARN
because there is no matching devm_kmalloc() resource for such bogus
pointers.
Improve the robustness and readability by:
- Using devm_kcalloc() for the pointer arrays so that all entries
start as NULL, ensuring that only genuinely initialised elements
may be freed and preventing spurious WARN_ON()s in the error path.
- Switching the allocations to sizeof(*ptr) / sizeof(**ptr) forms,
avoiding hard-coded element types and making the code more resilient
to future type changes.
- Dropping the redundant NULL checks before devm_kfree(), as
devm_kfree() safely handles NULL pointers.
The functional behaviour in the successful initialisation path remains
unchanged, while the error handling becomes simpler and less
error-prone.
Reviewed-by: fanggeng <fanggeng@lixiang.com>
Signed-off-by: Liang Jie <liangjie@lixiang.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
In mt8189-pinctrl driver, a previous commit changed the register base
name array (mt8189_pinctrl_register_base_names) entry name and order to
align it with the same name and order as the "mediatek,mt8189-pinctrl"
devicetree bindings. The new order (by ascending register address) now
causes an issue with MT8189 pinctrl configuration.
MT8189 SoC has multiple base addresses for the pin configuration
registers. Several constant data structures, declaring each pin
configuration, are using PIN_FIELD_BASE() macro which i_base parameter
indicates for a given pin the lookup index in the base register address
array of the driver internal data for the configuration register
read/write accesses. But in practice, this parameter is given a
hardcoded numerical value that corresponds to the expected base
register entry index in mt8189_pinctrl_register_base_names array.
Since this array reordering, the i_base index matching is no more
correct.
So, in order to avoid modifying over a thousand of PIN_FIELD_BASE()
calls, restore previous mt8189_pinctrl_register_base_names entry order.
Fixes: 518919276c ("pinctrl: mediatek: mt8189: align register base names to dt-bindings ones")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Pull pin control updates from Linus Walleij:
"The technical details below. For me the CIX Semi and Axis
Communications ARTPEC-9 SoCs were the most interesting new drivers in
this merge window.
Core changes:
- Handle per-direction skew control in the generic pin config
- Drop the pointless subsystem boilerplate banner message during
boot. Less noise in the console. It's available as debug message if
someone really want it
New drivers:
- Samsung Exynos 8890 SoC support
- Samsung Exynos derived Axis Communications ARTPEC-9 SoC support.
These guys literally live next door to me, ARTPEC spells out "Axis
Real-Time Picture Encoding Chip" and is tailored for camera image
streams and is something they have evolved for a quarter of a
century
- Mediatek MT6878 SoC support
- Qualcomm Glymur PMIC support (mostly just compatible strings)
- Qualcomm Kaanapali SoC TLMM support
- Microchip pic64gx "gpio2" SoC support
- Microchip Polarfire "iomux0" SoC support
- CIX Semiconductors SKY1 SoC support
- Rockchip RK3506 SoC support
- Airhoa AN7583 chip support
Improvements:
- Improvements for ST Microelectronics STM32 handling of skew
settings so input and output can have different skew settings
- A whole bunch of device tree binding cleanups: Marvell Armada and
Berlin, Actions Semiconductor S700 and S900, Broadcom Northstar 2
(NS2), Bitmain BM1880 and Spreadtrum SC9860 are moved over to
schema"
* tag 'pinctrl-v6.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
pinctrl: add CONFIG_OF dependencies for microchip drivers
pinctrl: starfive: use dynamic GPIO base allocation
pinctrl: single: Fix incorrect type for error return variable
MAINTAINERS: Change Linus Walleij mail address
pinctrl: cix: Fix obscure dependency
dt-bindings: pinctrl: cix,sky1-pinctrl: Drop duplicate newline
dt-bindings: pinctrl: aspeed,ast2600-pinctrl: Add PCIe RC PERST# group
pinctrl: airoha: Fix AIROHA_PINCTRL_CONFS_DRIVE_E2 in an7583_pinctrl_match_data
pinctrl: airoha: fix pinctrl function mismatch issue
pinctrl: cherryview: Convert to use intel_gpio_add_pin_ranges()
pinctrl: intel: Export intel_gpio_add_pin_ranges()
pinctrl: renesas: rzg2l: Refactor OEN register PWPR handling
pinctrl: airoha: convert comma to semicolon
pinctrl: elkhartlake: Switch to INTEL_GPP() macro
pinctrl: cherryview: Switch to INTEL_GPP() macro
pinctrl: emmitsburg: Switch to INTEL_GPP() macro
pinctrl: denverton: Switch to INTEL_GPP() macro
pinctrl: cedarfork: Switch to INTEL_GPP() macro
pinctrl: airoha: add support for Airoha AN7583 PINs
dt-bindings: pinctrl: airoha: Document AN7583 Pin Controller
...
Clang warns (or errors with CONFIG_WERROR=y / W=e):
pinctrl/mediatek/pinctrl-airoha.c:2064:41: error: variable 'an7583_pinctrl_drive_e2_conf' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
2064 | static const struct airoha_pinctrl_conf an7583_pinctrl_drive_e2_conf[] = {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Due to a typo, an7583_pinctrl_drive_e2_conf is only used within
ARRAY_SIZE() (hence no instance of -Wunused-variable), which is
evaluated at compile time, so it will not be needed in the final object
file.
Fix the .confs assignment for AIROHA_PINCTRL_CONFS_DRIVE_E2 in
an7583_pinctrl_match_data to clear up the warning.
Closes: https://github.com/ClangBuiltLinux/linux/issues/2142
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The blamed commit made the following changes:
-#define PINCTRL_FUNC_DESC(id)...
- .desc = PINCTRL_PINFUNCTION(#id, ...
+#define PINCTRL_FUNC_DESC(id, table)...
+ .desc = PINCTRL_PINFUNCTION(#id, ...
- PINCTRL_FUNC_DESC(pon)...
+ PINCTRL_FUNC_DESC("pon", pon)...
It's clear that the id of funcs doesn't match the definition.
Remove redundant #string from the definition to fix this issue:
pinctrl-airoha ...: invalid function mdio in map table
Fixes: 4043b0c45f ("pinctrl: airoha: generalize pins/group/function/confs handling")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Acked-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add all the required entry to add suppot for Airoha AN7583 PINs.
Where possible the same function group are used from Airoha EN7581 to
reduce code duplication.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PWM GPIO struct definition follow the same pattern for every GPIO
pin hence it can be converted to a macro.
Create 2 macro one for normal mux and one for ext mux and convert all
the entry to these new macro to reduce code size.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PHY LED GPIO pinctrl struct definition is very similar across the
different 4 PHY and 2 LED and it can be generelized to a macro.
To reduce code size, convert them to a common macro.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation for support of Airoha AN7583, generalize
pins/group/function/confs handling and move them in match_data.
Inner function will base the values on the pinctrl priv struct instead of
relying on hardcoded struct.
This permits to use different PIN data while keeping the same logic.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mt8189-pinctrl driver requires to probe that a device tree uses
in the device node the same names than mt8189_pinctrl_register_base_names
array. But they are not matching the required ones in the
"mediatek,mt8189-pinctrl" dt-bindings, leading to possible dtbs check
issues. The mt8189_pinctrl_register_base_names entry order is also
different.
So, align all mt8189_pinctrl_register_base_names entry names and order
on dt-bindings.
Fixes: a3fe1324c3 ("pinctrl: mediatek: Add pinctrl driver for mt8189")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mt8196-pinctrl driver requires to probe that a device tree uses
in the device node the same names than mt8196_pinctrl_register_base_names
array. But they are not matching the required ones in the
"mediatek,mt8196-pinctrl" dt-bindings, leading to possible dtbs check
issues.
So, align all mt8196_pinctrl_register_base_names entries on dt-bindings
ones.
Fixes: f7a29377c2 ("pinctrl: mediatek: Add pinctrl driver on mt8196")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"We have GPIO awareness in the pin control core and an interesting
AAEON driver.
Core changes:
- Allow pins to be identified/marked as GPIO mode with a special
callback.
The pin controller core is now "aware" if a pin is in GPIO mode if
the callback is implemented in the driver, and can thus be marked
as "strict", i.e. disallowing simultaneous use of a line as GPIO
and another function such as I2C.
This is enabled in the Qualcomm TLMM driver and also implemeted
from day 1 in the new Broadcom STB driver
- Rename the pin config option PIN_CONFIG_OUTPUT to PIN_CONFIG_LEVEL
to better describe what the config is doing, as well as making it
more intuitive what shall be returned when reading this property
New drivers:
- Qualcomm SDM660 LPASS LPI TLMM pin controller subdriver
- Qualcomm Glymur family pin controller driver
- Broadcom STB family pin controller driver
- Tegra186 pin controller driver
- AAEON UP pin controller support.
This is some special pin controller that works as an external
advanced line MUX and amplifier for signals from an Intel SoC. A
cooperative effort with the GPIO maintainer was needed to reach a
solution where we reuse code from the GPIO aggregator/forwarder
driver
- Renesas RZ/T2H and RZ/N2H pin controller support
- Axis ARTPEC-8 subdriver for the Samsung pin controller driver
Improvements:
- Output enable (OEN) support in the Renesas RZG2L driver
- Properly support bias pull up/down in the pinctrl-single driver
- Move over all GPIO portions using generic MMIO GPIO to the new
generic GPIO chip management which has a nice and separate API
- Proper DT bindings for some older Broadcom SoCs
- External GPIO (EGPIO) support in the Qualcomm SM8250
Deleted code:
- Dropped the now unused Samsung S3C24xx drivers"
* tag 'pinctrl-v6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: use more common syntax for compound literals
pinctrl: Simplify printks with pOF format
pinctrl: qcom: Add SDM660 LPASS LPI TLMM
dt-bindings: pinctrl: qcom: Add SDM660 LPI pinctrl
pinctrl: qcom: lpass-lpi: Add ability to use custom pin offsets
pinctrl: qcom: Add glymur pinctrl driver
dt-bindings: pinctrl: qcom: Add Glymur pinctrl
pinctrl: qcom: sm8250: Add egpio support
pinctrl: generic: rename PIN_CONFIG_OUTPUT to LEVEL
pinctrl: keembay: fix double free in keembay_build_functions()
pinctrl: spacemit: fix typo in PRI_TDI pin name
pinctrl: eswin: Fix regulator error check and Kconfig dependency
pinctrl: bcm: Add STB family pin controller driver
dt-bindings: pinctrl: Add support for Broadcom STB pin controller
pinctrl: qcom: make the pinmuxing strict
pinctrl: qcom: mark the `gpio` and `egpio` pins function as non-strict functions
pinctrl: qcom: add infrastructure for marking pin functions as GPIOs
pinctrl: allow to mark pin functions as requestable GPIOs
pinctrl: qcom: use generic pin function helpers
pinctrl: make struct pinfunction a pointer in struct function_desc
...
With further testing with an attached Aeonsemi it was discovered that
the pinctrl MDIO function applied the wrong bitmask. The error was
probably caused by the confusing documentation related to these bits.
Inspecting what the bootloader actually configure, the SGMII_MDIO_MODE
is never actually set but instead it's set force enable to the 2 GPIO
(gpio 1-2) for MDC and MDIO pin.
The usage of GPIO might be confusing but this is just to instruct the
SoC to not mess with those 2 PIN and as Benjamin reported it's also an
Errata of 7581. The FORCE_GPIO_EN doesn't set them as GPIO function
(that is configured by a different register) but it's really to actually
""enable"" those lines.
Normally the SoC should autodetect this by HW but it seems AN7581 have
problem with this and require this workaround to force enable the 2 pin.
Applying this configuration permits correct functionality of any
externally attached PHY.
Cc: stable@vger.kernel.org
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Benjamin Larsson <benjamin.larsson@genexis.eu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In all the MUX value for LED1 GPIO46 there is a Copy-Paste error where
the MUX value is set to LED0_MODE_MASK instead of LED1_MODE_MASK.
This wasn't notice as there were no board that made use of the
secondary PHY LED but looking at the internal Documentation the actual
value should be LED1_MODE_MASK similar to the other GPIO entry.
Fix the wrong value to apply the correct MUX configuration.
Cc: stable@vger.kernel.org
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This generic pin config property is confusingly named so let's
rename it to make things clearer.
There are already drivers in the tree that use PIN_CONFIG_OUTPUT
to *read* the value of an output driven pin, which is a big
semantic confusion for the head: are we then reading the
setting of the output or the actual value/level that is put
out on the pin?
We already have PIN_CONFIG_OUTPUT_ENABLE that turns on driver
buffers for output, so this can by logical conclusion only
drive the voltage level if it should be any different.
But if we read the pin, are we then reading the *setting* of
the output value or the *actual* value we can see on the
line?
If the pin has not first been set into output mode with
PIN_CONFIG_OUTPUT_ENABLE, but is instead in some input mode
or tristate, what will reading this property actually
return?
Reading the current users reading this property it is clear
that what we read is the logical level of the pin as 0 or 1
depending on if it is low or high.
Rename it to PIN_CONFIG_LEVEL so it is crystal clear that
we set or read the voltage level of the pin and nothing else.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We currently duplicate the entire struct pinfunction object in
pinmux_generic_add_pinfunction(). While this is inevitable when the
arguments come in split through pinmux_generic_add_function(), users of
pinmux_generic_add_pinfunction() will typically pass addresses of
structures in .rodata, meaning we can try to avoid the duplication with
the help from kmemdup_const(). To that end: don't wrap the entire struct
pinfunction in struct function_desc but rather just store the address.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
