Add register sequences for PCIe + XAUI multilink configuration for
100MHz reference clock.
The register sequences are fetched from a table by indexing entries based
on unique 'keys' generated by the Bitwise OR defined below:
REFCLK0_RATE | REFCLK1_RATE | LINK0_TYPE | LINK1_TYPE | SSC_TYPE
As of now, LINK_TYPE is a 3-bit value corresponding to the PHY type.
With the introduction of TYPE_XAUI, we need a 4-bit value to represent
the LINK_TYPE as TYPE_XAUI has the numerical value 8. Hence, extend the
LINKx_MASK macros to 4-bit masks. While at it, extend REFCLKx_MASK macros
as well to 4-bit masks to support reference clock frequencies that will be
added in the future.
Adjust the 'LINKx_SHIFT' and the 'REFCLKx_SHIFT' macros to account for
the aforementioned changes made to the masks.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
[s-vadapalli: elaborated on changes made to macros in the commit message]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260112054636.108027-3-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Do read-modify-write so that we re-use the characterized reset value as
specified in TRM [1] to program calibration wait time which defines number
of cycles to wait for after startup state machine is in bandgap enable
state.
This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
AM62L and J721E SoC since earlier calibration wait time was getting
overwritten to zero value thus failing the PLL to lockup and causing
timeout.
[1] AM62P TRM (Section 14.8.6.3.2.1.1 DPHY_TX_DPHYTX_CMN0_CMN_DIG_TBIT2):
Link: https://www.ti.com/lit/pdf/spruj83
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-3-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled by programming DPHY_CMN_SSM register, but driver was
polling them before the common state machine was enabled which is
incorrect. This is as per the DPHY initialization sequence as mentioned in
J721E TRM [1] at section "12.7.2.4.1.2.1 Start-up Sequence Timing Diagram".
It shows O_CMN_READY polling at the end after common configuration pin
setup where the common configuration pin setup step enables state machine
as referenced in "Table 12-1533. Common Configuration-Related Setup
mentions state machine"
To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
assertion.
- As state machine and clocks get enabled in power_on callback only, move
the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after state
machine gets enabled.
- The configure callback only saves the PLL configuration received from the
client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can re-configure
the PLL by following up a power_off, configure, power_on sequence.
[1]: https://www.ti.com/lit/zip/spruil1
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-2-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull phy updates from Vinod Koul:
"New hardware support:
- ST STM32MP25 combophy support
- Sparx5 support for lan969x serdes and updates to driver to support
this
- NXP PTN3222 eUSB2 to USB2 redriver
- Qualcomm SAR2130P eusb2 support, QCS8300 USB DW3 and QMP USB2
support, X1E80100 QMP PCIe PHY Gen4 support, QCS615 and QCS8300 QMP
UFS PHY support and SA8775P eDP PHY support
- Rockchip rk3576 usbdp and rk3576 usb2 phy support
- Binding for Microchip ATA6561 can phy
Updates:
- Freescale driver updates from hdmi support
- Conversion of rockchip rk3228 hdmi phy binding to yaml
- Broadcom usb2-phy deprecated support dropped and USB init array
update for BCM4908
- TI USXGMII mode support in J7200
- Switch back to platform_driver::remove() subsystem update"
* tag 'phy-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (59 commits)
phy: qcom: qmp: Fix lecacy-legacy typo
phy: lan969x-serdes: add support for lan969x serdes driver
dt-bindings: phy: sparx5: document lan969x
phy: sparx5-serdes: add support for branching on chip type
phy: sparx5-serdes: add indirection layer to register macros
phy: sparx5-serdes: add function for getting the CMU index
phy: sparx5-serdes: add ops to match data
phy: sparx5-serdes: add constant for the number of CMU's
phy: sparx5-serdes: add constants to match data
phy: sparx5-serdes: add support for private match data
phy: bcm-ns-usb2: drop support for old binding variant
dt-bindings: phy: bcm-ns-usb2-phy: drop deprecated variant
dt-bindings: phy: Add QMP UFS PHY compatible for QCS8300
dt-bindings: phy: qcom: snps-eusb2: Add SAR2130P compatible
dt-bindings: phy: ti,tcan104x-can: Document Microchip ATA6561
phy: airoha: Fix REG_CSR_2L_RX{0,1}_REV0 definitions
phy: airoha: Fix REG_CSR_2L_JCPLL_SDM_HREN config in airoha_pcie_phy_init_ssc_jcpll()
phy: airoha: Fix REG_PCIE_PMA_TX_RESET config in airoha_pcie_phy_init_csr_2l()
phy: airoha: Fix REG_CSR_2L_PLL_CMN_RESERVE0 config in airoha_pcie_phy_init_clk_out()
phy: phy-rockchip-samsung-hdptx: Don't request RST_PHY/RST_ROPLL/RST_LCPLL
...
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/phy/ to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241009065307.504930-2-u.kleine-koenig@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Torrent SERDES can support at most two different protocols (PHY types).
This only mandates that the device-tree sub-nodes used to represent the
configuration should describe links with at-most two different protocols.
The existing implementation however imposes an artificial constraint that
allows only two links (device-tree sub-nodes). As long as at-most two
protocols are chosen, using more than two links to describe them in an
alternating configuration is still a valid configuration of the Torrent
SERDES.
A 3-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 1 => Link 1
Lane 2 => Protocol 2 => Link 2
Lane 3 => Protocol 1 => Link 3
A 4-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 2 => Link 2
Lane 2 => Protocol 1 => Link 3
Lane 3 => Protocol 2 => Link 4
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240805092607.143869-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'cdns_sierra_pll_mux_table' is not modified in this driver.
And it is only used as a "const u32 *".
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
60937 3894 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
After:
=====
text data bss dec hex filename
60897 3878 16 64791 fd17 drivers/phy/cadence/phy-cadence-sierra.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/43d881d52e3c1632ad197d4c2c18b6c481a13b24.1720723132.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_sierra_vals' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
60521 4310 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
After:
=====
text data bss dec hex filename
60937 3894 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0ccfd259fdf40475c89cfb22a64c6388e7c646b4.1720723132.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_reg_pairs' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
60489 4342 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
After:
=====
text data bss dec hex filename
60521 4310 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/c57ee8206ebba8c222d7d954335654384072b9ac.1720723132.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'cdns_torrent_refclk_driver_mux_table' is not modified in this driver.
And it is only used as a "const u32 *".
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
93578 4798 16 98392 18058 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
93606 4790 16 98412 1806c drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/34e23ceb6b7b7eb730ee8deee21d231b504dc65f.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_torrent_vals' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
92234 6078 16 98328 18018 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
93578 4798 16 98392 18058 drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d9d135ee9b806726766a1bc5e1404267939aa637.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_torrent_vals_entry' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
85130 13214 16 98360 18038 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
92234 6078 16 98328 18018 drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/dcc4e539999a840b3fd8f40fd8fd7523390232ac.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_reg_pairs' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
78154 20222 16 98392 18058 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
85130 13214 16 98360 18038 drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/803684a6f0c24d7e091dc8d285dd49c6fd31a010.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
