This patch
- makes mdio_device.c part of libphy
- makes mdio_device_(un)register_reset() static
- moves mdiobus_(un)register_device() from mdio_bus.c to mdio_device.c,
stops exporting both functions and makes them private to phylib
This further decouples the MDIO consumer functionality from libphy.
Note: This makes MDIO driver registration part of phylib, therefore
adjust Kconfig dependencies where needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c6dbf9b3-3ca0-434b-ad3a-71fe602ab809@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
"family" is an enum, thus cast of pointer on 64-bit compile test with
clang W=1 causes:
phy-bcm-ns-usb3.c:206:17: error: cast to smaller integer type 'enum bcm_ns_family' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
This was already fixed in commit bd6e74a2f0 ("phy: broadcom: ns-usb3:
fix Wvoid-pointer-to-enum-cast warning") but then got bad in commit
21bf6fc47a ("phy: Use device_get_match_data()").
Note that after various discussions the preferred cast is via "unsigned
long", not "uintptr_t".
Fixes: 21bf6fc47a ("phy: Use device_get_match_data()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20251224115533.154162-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drivers should generally be quiet on successful probe, but this is not
followed by some PHY drivers, for example:
snps-eusb2-hsphy 88e1000.phy: Registered Snps-eUSB2 phy
qcom-eusb2-repeater c432000.spmi:pmic@7:phy@fd00: Registered Qcom-eUSB2 repeater
qcom-eusb2-repeater c432000.spmi:pmic@a:phy@fd00: Registered Qcom-eUSB2 repeater
qcom-eusb2-repeater c432000.spmi:pmic@b:phy@fd00: Registered Qcom-eUSB2 repeater
snps-eusb2-hsphy fd3000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy fd9000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy fde000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy 88e0000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy 88e2000.phy: Registered Snps-eUSB2 phy
Drop (or demote to debug level) unnecessary registration info messages
to make boot logs a little less noisy.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250523085112.11287-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull phy updates from Vinod Koul:
"New hardware support:
- ST STM32MP25 combophy support
- Sparx5 support for lan969x serdes and updates to driver to support
this
- NXP PTN3222 eUSB2 to USB2 redriver
- Qualcomm SAR2130P eusb2 support, QCS8300 USB DW3 and QMP USB2
support, X1E80100 QMP PCIe PHY Gen4 support, QCS615 and QCS8300 QMP
UFS PHY support and SA8775P eDP PHY support
- Rockchip rk3576 usbdp and rk3576 usb2 phy support
- Binding for Microchip ATA6561 can phy
Updates:
- Freescale driver updates from hdmi support
- Conversion of rockchip rk3228 hdmi phy binding to yaml
- Broadcom usb2-phy deprecated support dropped and USB init array
update for BCM4908
- TI USXGMII mode support in J7200
- Switch back to platform_driver::remove() subsystem update"
* tag 'phy-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (59 commits)
phy: qcom: qmp: Fix lecacy-legacy typo
phy: lan969x-serdes: add support for lan969x serdes driver
dt-bindings: phy: sparx5: document lan969x
phy: sparx5-serdes: add support for branching on chip type
phy: sparx5-serdes: add indirection layer to register macros
phy: sparx5-serdes: add function for getting the CMU index
phy: sparx5-serdes: add ops to match data
phy: sparx5-serdes: add constant for the number of CMU's
phy: sparx5-serdes: add constants to match data
phy: sparx5-serdes: add support for private match data
phy: bcm-ns-usb2: drop support for old binding variant
dt-bindings: phy: bcm-ns-usb2-phy: drop deprecated variant
dt-bindings: phy: Add QMP UFS PHY compatible for QCS8300
dt-bindings: phy: qcom: snps-eusb2: Add SAR2130P compatible
dt-bindings: phy: ti,tcan104x-can: Document Microchip ATA6561
phy: airoha: Fix REG_CSR_2L_RX{0,1}_REV0 definitions
phy: airoha: Fix REG_CSR_2L_JCPLL_SDM_HREN config in airoha_pcie_phy_init_ssc_jcpll()
phy: airoha: Fix REG_PCIE_PMA_TX_RESET config in airoha_pcie_phy_init_csr_2l()
phy: airoha: Fix REG_CSR_2L_PLL_CMN_RESERVE0 config in airoha_pcie_phy_init_clk_out()
phy: phy-rockchip-samsung-hdptx: Don't request RST_PHY/RST_ROPLL/RST_LCPLL
...
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/phy/ to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241009065307.504930-2-u.kleine-koenig@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Broadcom USB PHY driver contains a lookup table
(`reg_bits_map_tables`) to resolve register bitmaps unique to certain
versions of the USB PHY as found in various Broadcom chip families.
Historically, this table was just kept carefully in sync with the
"selector" enum every time the latter changed to ensure consistency.
However, a recent commit [1] introduced two new enumerators but did not
adjust the array for BCM4908, thus breaking the xHCI controller (and
boot process) on this platform and revealing the fragility of this
approach.
Since these arrays are a little sparse (many elements are zero) and the
position of the array elements is significant only insofar as they agree
with the enumerators, designated initializers are a better fit than
positional initializers here. Convert this table accordingly.
[1] 4536fe9640 ("phy: usb: suppress OC condition for 7439b2")
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Justin Chen <justin.chen@broadcom.com>
Link: https://lore.kernel.org/r/20241004034131.1363813-3-CFSworks@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Broadcom USB PHY driver contains a lookup table
(`reg_bits_map_tables`) to resolve register bitmaps unique to certain
versions of the USB PHY as found in various Broadcom chip families. A
recent commit (see 'fixes' tag) introduced two new elements to each chip
family in this table -- except for one: BCM4908. This resulted in the
xHCI controller not being initialized correctly, causing a panic on
boot.
The next patch will update this table to use designated initializers in
order to prevent this from happening again. For now, just add back the
missing array elements to resolve the regression.
Fixes: 4536fe9640 ("phy: usb: suppress OC condition for 7439b2")
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20241004034131.1363813-2-CFSworks@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The COMMONONN bit turns off the PHY when the host controller puts it
into suspend state. This can happen during the following...
- Nothing is connected to the port
- The host controller goes into low power mode whatever due to auto
suspend or system suspend.
With COMMONONN we also must unset U2_FREECLK_EXISTS since the UTMI
clock is fed by the PHY.
With these changes we see a power savings of ~12mW when port is in
suspend.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Link: https://lore.kernel.org/r/1686859578-45242-2-git-send-email-justin.chen@broadcom.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
