Pull char / misc / iio driver updates from Greg KH:
"Here is the big char/misc/iio and other small driver subsystem pull
request for 6.16-rc1.
Overall, a lot of individual changes, but nothing major, just the
normal constant forward progress of new device support and cleanups to
existing subsystems. Highlights in here are:
- Large IIO driver updates and additions and device tree changes
- Android binder bugfixes and logfile fixes
- mhi driver updates
- comedi driver updates
- counter driver updates and additions
- coresight driver updates and additions
- echo driver removal as there are no in-kernel users of it
- nvmem driver updates
- spmi driver updates
- new amd-sbi driver "subsystem" and drivers added
- rust miscdriver binding documentation fix
- other small driver fixes and updates (uio, w1, acrn, hpet,
xillybus, cardreader drivers, fastrpc and others)
All of these have been in linux-next for quite a while with no
reported problems"
* tag 'char-misc-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (390 commits)
binder: fix yet another UAF in binder_devices
counter: microchip-tcb-capture: Add watch validation support
dt-bindings: iio: adc: Add ROHM BD79100G
iio: adc: add support for Nuvoton NCT7201
dt-bindings: iio: adc: add NCT7201 ADCs
iio: chemical: Add driver for SEN0322
dt-bindings: trivial-devices: Document SEN0322
iio: adc: ad7768-1: reorganize driver headers
iio: bmp280: zero-init buffer
iio: ssp_sensors: optimalize -> optimize
HID: sensor-hub: Fix typo and improve documentation
iio: admv1013: replace redundant ternary operator with just len
iio: chemical: mhz19b: Fix error code in probe()
iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS
iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS
iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS
iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros
iio: make IIO_DMA_MINALIGN minimum of 8 bytes
...
R-Car Gen4 SoCs contain fuses indicating hardware support or hardware
(e.g. tuning) parameters. Add a driver to access the state of the
fuses. This supports two types of hardware fuse providers:
1. E-FUSE non-volatile memory accessible through the Pin Function
Controller on R-Car V3U and S4-8,
2. E-FUSE non-volatile memory accessible through OTP_MEM on R-Car V4H
and V4M.
The state of the cells can be read using the NVMEM framework, either
from kernel space (e.g. by the Renesas UFSHCD driver), or from
userspace.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20241030140315.40562-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current layout support was initially written without modules support in
mind. When the requirement for module support rose, the existing base
was improved to adopt modularization support, but kind of a design flaw
was introduced. With the existing implementation, when a storage device
registers into NVMEM, the core tries to hook a layout (if any) and
populates its cells immediately. This means, if the hardware description
expects a layout to be hooked up, but no driver was provided for that,
the storage medium will fail to probe and try later from
scratch. Even if we consider that the hardware description shall be
correct, we could still probe the storage device (especially if it
contains the rootfs).
One way to overcome this situation is to consider the layouts as
devices, and leverage the native notifier mechanism. When a new NVMEM
device is registered, we can populate its nvmem-layout child, if any,
and wait for the matching to be done in order to get the cells (the
waiting can be easily done with the NVMEM notifiers). If the layout
driver is compiled as a module, it should automatically be loaded. This
way, there is no strong order to enforce, any NVMEM device creation
or NVMEM layout driver insertion will be observed as a new event which
may lead to the creation of additional cells, without disturbing the
probes with costly (and sometimes endless) deferrals.
In order to achieve that goal we create a new bus for the nvmem-layouts
with minimal logic to match nvmem-layout devices with nvmem-layout
drivers. All this infrastructure code is created in the layouts.c file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231215111536.316972-7-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add i.MX93 OCOTP support. i.MX93 OCOTP has two parts: Fuse shadow
block(fsb) and fuse managed by ELE. The FSB part could be directly
accessed with MMIO, the ELE could only be accessed with ELE API.
Currently the ELE API is not ready, so NULL function callback is used,
but it was tested with downstream ELE API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Message-ID: <20230611140330.154222-22-srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVMEM layouts are used to generate NVMEM cells during runtime. Think of
an EEPROM with a well-defined conent. For now, the content can be
described by a device tree or a board file. But this only works if the
offsets and lengths are static and don't change. One could also argue
that putting the layout of the EEPROM in the device tree is the wrong
place. Instead, the device tree should just have a specific compatible
string.
Right now there are two use cases:
(1) The NVMEM cell needs special processing. E.g. if it only specifies
a base MAC address offset and you need to add an offset, or it
needs to parse a MAC from ASCII format or some proprietary format.
(Post processing of cells is added in a later commit).
(2) u-boot environment parsing. The cells don't have a particular
offset but it needs parsing the content to determine the offsets
and length.
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230404172148.82422-14-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
U-Boot stores its setup as environment variables. It's a list of
key-value pairs stored on flash device with a custom header.
This commit adds an NVMEM driver that:
1. Provides NVMEM access to environment vars binary data
2. Extracts variables as NVMEM cells
Current Linux's NVMEM sysfs API allows reading whole NVMEM data block.
It can be used by user-space tools for reading U-Boot env vars block
without the hassle of finding its location. Parsing will still need to
be re-done there.
Kernel-parsed NVMEM cells can be read however by Linux drivers. This may
be useful for Ethernet drivers for reading device MAC address which is
often stored as U-Boot env variable.
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220916122100.170016-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Microchip OTP controller available on SAMA7G5. The OTPC
controls the access to a non-volatile memory. The memory behind OTPC is
organized into packets, packets are composed by a fixed length header
(4 bytes long) and a variable length payload (payload length is available
in the header). When software request the data at an offset in memory
the OTPC will return (via header + data registers) the whole packet that
has a word at that offset. For the OTP memory layout like below:
offset OTP Memory layout
. .
. ... .
. .
0x0E +-----------+ <--- packet X
| header X |
0x12 +-----------+
| payload X |
0x16 | |
| |
0x1A | |
+-----------+
. .
. ... .
. .
if user requests data at address 0x16 the data started at 0x0E will be
returned by controller. User will be able to fetch the whole packet
starting at 0x0E (or parts of the packet) via proper registers. The same
packet will be returned if software request the data at offset 0x0E or
0x12 or 0x1A.
The OTP will be populated by Microchip with at least 2 packets first one
being boot configuration packet and the 2nd one being temperature
calibration packet. The packet order will be preserved b/w different chip
revisions but the packet sizes may change.
For the above reasons and to keep the same software able to work on all
chip variants the read function of the driver is working with a packet
id instead of an offset in OTP memory.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220706100627.6534-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiko Stuebner
Christian Marangi
Ciprian Costea
Linus Torvalds
Hector Martin
André Draszik
Geert Uytterhoeven
Miquel Raynal
Komal Bajaj
Richard Alpe
Peng Fan
Michael Walle
Patrick Delaunay
Horatiu Vultur
Rafał Miłecki
Claudiu Beznea
Sven Peter
Vincent Shih
Emmanuel Gil Peyrot
Nicolas Saenz Julienne
Srinivas Kandagatla