This patch
- makes mdio_device.c part of libphy
- makes mdio_device_(un)register_reset() static
- moves mdiobus_(un)register_device() from mdio_bus.c to mdio_device.c,
stops exporting both functions and makes them private to phylib
This further decouples the MDIO consumer functionality from libphy.
Note: This makes MDIO driver registration part of phylib, therefore
adjust Kconfig dependencies where needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c6dbf9b3-3ca0-434b-ad3a-71fe602ab809@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ethernet provides a wide variety of layer 1 protocols and standards for
data transmission. The front-facing ports of an interface have their own
complexity and configurability.
Introduce a representation of these front-facing ports. The current code
is minimalistic and only support ports controlled by PHY devices, but
the plan is to extend that to SFP as well as raw Ethernet MACs that
don't use PHY devices.
This minimal port representation allows describing the media and number
of pairs of a BaseT port. From that information, we can derive the
linkmodes usable on the port, which can be used to limit the
capabilities of an interface.
For now, the port pairs and medium is derived from devicetree, defined
by the PHY driver, or populated with default values (as we assume that
all PHYs expose at least one port).
The typical example is 100M ethernet. 100BaseTX works using only 2
pairs on a Cat 5 cables. However, in the situation where a 10/100/1000
capable PHY is wired to its RJ45 port through 2 pairs only, we have no
way of detecting that. The "max-speed" DT property can be used, but a
more accurate representation can be used :
mdi {
connector-0 {
media = "BaseT";
pairs = <2>;
};
};
From that information, we can derive the max speed reachable on the
port.
Another benefit of having that is to avoid vendor-specific DT properties
(micrel,fiber-mode or ti,fiber-mode).
This basic representation is meant to be expanded, by the introduction
of port ops, userspace listing of ports, and support for multi-port
devices.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260108080041.553250-4-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By reading the datasheets for the KS8995 it is obvious that this
is a 100 Mbit DSA switch.
Let us start the refactoring by moving it to the DSA subsystem to
preserve development history.
Verified that the chip still probes the same after this patch
provided CONFIG_HAVE_NET_DSA, CONFIG_NET_DSA and CONFIG_DSA_KS8995
are selected.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250813-ks8995-to-dsa-v1-1-75c359ede3a5@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the MaxLinear MxL86110 Gigabit Ethernet PHY, a low-power,
cost-optimized transceiver supporting 10/100/1000 Mbps over twisted-pair
copper, compliant with IEEE 802.3.
The driver implements basic features such as:
- Device initialization
- RGMII interface timing configuration
- Wake-on-LAN support
- LED initialization and control via /sys/class/leds
This driver has been tested on multiple Variscite boards, including:
- VAR-SOM-MX93 (i.MX93)
- VAR-SOM-MX8M-PLUS (i.MX8MP)
Example boot log showing driver probe:
[ 7.692101] imx-dwmac 428a0000.ethernet eth0:
PHY [stmmac-0:00] driver [MXL86110 Gigabit Ethernet] (irq=POLL)
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250521212821.593057-1-stefano.radaelli21@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for Aeonsemi AS21xxx 10G C45 PHYs. These PHYs integrate
an IPC to setup some configuration and require special handling to
sync with the parity bit. The parity bit is a way the IPC use to
follow correct order of command sent.
Supported PHYs AS21011JB1, AS21011PB1, AS21010JB1, AS21010PB1,
AS21511JB1, AS21511PB1, AS21510JB1, AS21510PB1, AS21210JB1,
AS21210PB1 that all register with the PHY ID 0x7500 0x7510
before the firmware is loaded.
They all support up to 5 LEDs with various HW mode supported.
While implementing it was found some strange coincidence with using the
same logic for implementing C22 in MMD regs in Broadcom PHYs.
For reference here the AS21xxx PHY name logic:
AS21x1xxB1
^ ^^
| |J: Supports SyncE/PTP
| |P: No SyncE/PTP support
| 1: Supports 2nd Serdes
| 2: Not 2nd Serdes support
0: 10G, 5G, 2.5G
5: 5G, 2.5G
2: 2.5G
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After having factored out the provider part from mdio_bus.c, we can
make the mdio consumer / device layer a separate module. This also
allows to remove Kconfig symbol MDIO_DEVICE.
The module init / exit functions from mdio_bus.c no longer have to be
called from phy_device.c. The link order defined in
drivers/net/phy/Makefile ensures that init / exit functions are called
in the right order.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dba6b156-5748-44ce-b5e2-e8dc2fcee5a7@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After 52358dd63e ("net: phy: remove function stubs") there's a
problem if CONFIG_MDIO_BUS is set, but CONFIG_PHYLIB is not.
mdiobus_scan() uses phylib functions like get_phy_device().
Bringing back the stub wouldn't make much sense, because it would
allow to compile mdiobus_scan(), but the function would be unusable.
The stub returned NULL, and we have the following in mdiobus_scan():
phydev = get_phy_device(bus, addr, c45);
if (IS_ERR(phydev))
return phydev;
So calling mdiobus_scan() w/o CONFIG_PHYLIB would cause a crash later in
mdiobus_scan(). In general the PHYLIB functionality isn't optional here.
Consequently, MDIO bus providers depend on PHYLIB.
Therefore factor it out and build it together with the libphy core
modules. In addition make all MDIO bus providers under /drivers/net/mdio
depend on PHYLIB. Same applies to enetc MDIO bus provider. Note that
PHYLIB selects MDIO_DEVRES, therefore we can omit this here.
Fixes: 52358dd63e ("net: phy: remove function stubs")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504270639.mT0lh2o1-lkp@intel.com/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c74772a9-dab6-44bf-a657-389df89d85c2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The canonical definition for all the link modes is in linux/ethtool.h,
which is complemented by the link_mode_params array stored in
net/ethtool/common.h . That array contains all the metadata about each
of these modes, including the Speed and Duplex information.
Phylib and phylink needs that information as well for internal
management of the link, which was done by duplicating that information
in locally-stored arrays and lookup functions. This makes it easy for
developpers adding new modes to forget modifying phylib and phylink
accordingly.
However, the link_mode_params array in net/ethtool/common.c is fairly
inefficient to search through, as it isn't sorted in any manner. Phylib
and phylink perform a lot of lookup operations, mostly to filter modes
by speed and/or duplex.
We therefore introduce the link_caps private array in phy_caps.c, that
indexes linkmodes in a more efficient manner. Each element associated a
tuple <speed, duplex> to a bitfield of all the linkmodes runs at these
speed/duplex.
We end-up with an array that's fairly short, easily addressable and that
it optimised for the typical use-cases of phylib/phylink.
That array is initialized at the same time as phylib. As the
link_mode_params array is part of the net stack, which phylink depends
on, it should always be accessible from phylib.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-3-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Re-organize MediaTek ethernet phy driver files and get ready to integrate
some common functions and add new 2.5G phy driver.
mtk-ge.c: MT7530 Gphy on MT7621 & MT7531 Gphy
mtk-ge-soc.c: Built-in Gphy on MT7981 & Built-in switch Gphy on MT7988
mtk-2p5ge.c: Planned for built-in 2.5G phy on MT7988
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver supports Applied Micro Circuits Corporation QT2025 PHY,
based on a driver for Tehuti Networks TN40xx chips.
The original driver for TN40xx chips supports multiple PHY hardware
(AMCC QT2025, TI TLK10232, Aqrate AQR105, and Marvell 88X3120,
88X3310, and MV88E2010). This driver is extracted from the original
driver and modified to a PHY driver in Rust.
This has been tested with Edimax EN-9320SFP+ 10G network adapter.
Reviewed-by: Trevor Gross <tmgross@umich.edu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to. The PHY index can be
re-used for PHYs that are persistent.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to. The PHY index can be
re-used for PHYs that are persistent.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the driver for the Airoha EN8811H 2.5 Gigabit PHY. The phy supports
100/1000/2500 Mbps with auto negotiation only.
The driver uses two firmware files, for which updated versions are added to
linux-firmware already.
Note: At phy-address + 8 there is another device on the mdio bus, that
belongs to the EN881H. While the original driver writes to it, Airoha
has confirmed this is not needed. Therefore, communication with this
device is not included in this driver.
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326162305.303598-3-ericwouds@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
