Use the sensor's pre-calculated jiffies value to add appropriate
delay between frames according to the configured timing value.
The actual frame rate will vary depending on processing delays in
other media pipeline components.
Tested using yavta frame rate display with QCIF resolution:
yavta <video-node> --capture=<no_of_frames>
Signed-off-by: Faizel K B <faizel.kb@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
pixel_rate and hblank as read only parameter. vblank can be configured
to match the desired frame rate.
Default values are, pixel_rate - 160 MHz, hblank - 800.
vblank defaults to an equivalent value of 30 fps for resolutions less than
or equal to 1920x1080 and 10 fps for higher resolutions. For higher
resolutions, modify pixel_rate in the driver code.
fps = pixel_rate / ((width + hblank) * (height + vblank))
minimum vblank - 4, maximum vblank - 65535
The configured fps delay is pre-calculated into jiffies and
stored in the sensor's hw structure for efficient access by the
streamer thread.
Signed-off-by: Faizel K B <faizel.kb@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Move the vimc_sensor_device structure from vimc-sensor.c to
vimc-common.h to make it accessible to the vimc-streamer component.
Signed-off-by: Faizel K B <faizel.kb@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
The platform device name is already set by V4L2 and MC frameworks for
media device bus_info and V4L2 querycap bus_info fields. Don't do it in
the driver.
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The second argument to the ioctl handlers is not a file handle any more.
Rename it from 'void *fh' to 'void *priv', to avoid misconceptions. This
is particularly important in test drivers as they are meant to be used
as reference implementations.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Since commit 88785982a1 ("media: vb2: use lock if wait_prepare/finish
are NULL") it is no longer needed to set the wait_prepare/finish
vb2_ops callbacks as long as the lock field in vb2_queue is set.
Since the vb2_ops_wait_prepare/finish callbacks already rely on that field,
we can safely drop these callbacks.
This simplifies the code and this is a step towards the goal of deleting
these callbacks.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/media to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Store the active formats and crop rectangle in the subdevice active
state. This simplifies implementation of the format and selection
accessors, and allows using the v4l2_subdev_get_fmt() helper to
implement the .get_fmt() operation.
The active configuration that is used in the .process_frame() handler is
still stored in the vimc_scaler_device structure. The driver could
instead access the active state in the .process_frame() handler, but the
required locking could interfere with the real time constraints of the
frame processing. This data would be stored in registers in the
.s_stream() handler for real hardware, storing it in dedicated storage
thus mimics a real driver. To differentiate them from the rest of the
device private data, move the corresponding fields to a sub-structure of
vimc_scaler_device named hw.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Store the active formats and crop rectangle in the subdevice active
state. This simplifies implementation of the format and selection
accessors, and allows using the v4l2_subdev_get_fmt() helper to
implement the .get_fmt() operation.
The active configuration that is used in the .process_frame() handler is
still stored in the vimc_debayer_device structure. The driver could
instead access the active state in the .process_frame() handler, but the
required locking could interfere with the real time constraints of the
frame processing. This data would be stored in registers in the
.s_stream() handler for real hardware, storing it in dedicated storage
thus mimics a real driver. To differentiate them from the rest of the
device private data, move the corresponding fields to a sub-structure of
vimc_debayer_device named hw.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Store the active formats and crop rectangle in the subdevice active
state. This simplifies implementation of the format and selection
accessors, and allows using the v4l2_subdev_get_fmt() helper to
implement the .get_fmt() operation.
The active configuration that is used in the .process_frame() handler is
still stored in the vimc_sensor_device structure. The driver could
instead access the active state in the .process_frame() handler, but the
required locking could interfere with the real time constraints of the
frame processing. This data would be stored in registers in the
.s_stream() handler for real hardware, storing it in dedicated storage
thus mimics a real driver. To differentiate them from the rest of the
device private data, move the corresponding fields to a sub-structure of
vimc_sensor_device named hw.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Finalize subdev initialization for all subdevs that provide a
.init_state() operation. This creates an active state for all those
subdevs, which subsequent patches will use to simplify the
implementation of individual vimc entities.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Initialize the subdev internal_ops field in the vimc_ent_sd_register()
function. This handles the internal ops the same way as the subdev ops,
and prepares for moving to the V4L2 subdev active state API.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The vimc_ent_type structure contains static pointers to functions, and
no other information that need to be modified after initialization. Make
them const to avoid the risk of arbitrary code execution following an
overflow that would overwrite the structure's contents.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Instead of using 'min_queued_buffers' field to specify the
minimum number of buffers to be allocated when calling REQBUF
use 'min_reqbufs_allocation' field which is dedicated to this
purpose.
Change the minimum requested buffers to 2 for vivid-meta-out
and vivid-touch-cap drivers when creating the queues.
That allows to remove code which prohibe to allocate only
one buffer in their respective queue setup functions.
While at it rename vivid_create_queue() parameter.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Rename min_buffers_needed into min_queued_buffers and update
the documentation about it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: Drop the change where min_queued_buffers + 1 buffers would be]
[hverkuil: allocated. Now this patch only renames this field instead of making]
[hverkuil: a functional change as well.]
[hverkuil: Renamed 3 remaining min_buffers_needed occurrences.]
The subdev .init_cfg() operation is affected by two issues:
- It has long been extended to initialize a whole v4l2_subdev_state
instead of just a v4l2_subdev_pad_config, but its name has stuck
around.
- Despite operating on a whole subdev state and not being directly
exposed to the subdev users (either in-kernel or through the userspace
API), .init_cfg() is categorized as a subdev pad operation.
This participates in making the subdev API confusing for new developers.
Fix it by renaming the operation to .init_state(), and make it a subdev
internal operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net> # for imx415
Acked-by: Shuah Khan <skhan@linuxfoundation.org> # for vimc
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
[Sakari Ailus: Resolved a conflict in Renesas vsp1 driver.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
