Since there were no existing drivers for the AS3668 or related devices,
a new driver was introduced in a separate file. Similar devices were
reviewed, but none shared enough characteristics to justify code reuse.
As a result, this driver is written specifically for the AS3668.
Signed-off-by: Lukas Timmermann <linux@timmermann.space>
Link: https://patch.msgid.link/20260118165010.902086-3-linux@timmermann.space
Signed-off-by: Lee Jones <lee@kernel.org>
Pull LED updates from Lee Jones:
- pca955x: Add HW blink support, utilizing PWM0. It supports one
frequency across all blinking LEDs and falls back to software blink
if different frequencies are requested.
- trigger: netdev: Allow configuring LED blink interval via .blink_set
even when HW offload (.hw_control) is enabled.
- led-core: Fix a race condition where a quick LED_OFF followed by
another brightness set could leave the LED off incorrectly,
especially noticeable after the introduction of the ordered
workqueue.
- qcom-lpg: Add support for 6-bit PWM resolution alongside the existing
9-bit support.
- qcom-lpg: Fix PWM value capping to respect the selected resolution
(6-bit or 9-bit) for normal PWMs.
- qcom-lpg: Fix PWM value capping to respect the selected resolution
for Hi-Res PWMs.
- qcom-lpg: Fix calculation of the best period for Hi-Res PWMs to
prevent requested duty cycles from exceeding the maximum allowed by
the selected resolution.
- st1202: Add a check for the error code returned by devm_mutex_init().
- pwm-multicolor: Add a check for the return value of
fwnode_property_read_u32().
- st1202: Ensure hardware initialization (st1202_setup) happens before
DT node processing (st1202_dt_init).
- Kconfig: leds-st1202: Add select LEDS_TRIGGER_PATTERN as it's
required by the driver.
- lp8860: Drop unneeded explicit assignment to REGCACHE_NONE.
- pca955x: Refactor code with helper functions and rename some
functions/variables for clarity.
- pca955x: Pass driver data pointers instead of the I2C client to
helper functions.
- pca955x: Optimize probe LED selection logic to reduce I2C operations.
- pca955x: Revert the removal of pca95xx_num_led_regs() (renaming it to
pca955x_num_led_regs) as it's needed for HW blink support.
- st1202: Refactor st1202_led_set() to use the !! operator for boolean
conversion.
- st1202: Minor spacing and proofreading edits in comments.
- Directory Rename: Rename the drivers/leds/simple directory to
drivers/leds/simatic as the drivers within are not simple.
- mlxcpld: Remove unused include of acpi.h.
- nic78bx: Tidy up the ACPI ID table (remove ACPI_PTR, use
mod_devicetable.h, remove explicit driver_data initializer).
- tlc591xx: Convert text binding to YAML format, add child node
constraints, and fix typos/formatting in the example.
- qcom-lpg: Document the qcom,pm8937-pwm compatible string as a
fallback for qcom,pm8916-pwm.
* tag 'leds-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (23 commits)
leds: nic78bx: Tidy up ACPI ID table
leds: mlxcpld: Remove unused ACPI header inclusion
leds: rgb: leds-qcom-lpg: Fix calculation of best period Hi-Res PWMs
leds: rgb: leds-qcom-lpg: Fix pwm resolution max for Hi-Res PWMs
leds: rgb: leds-qcom-lpg: Fix pwm resolution max for normal PWMs
leds: Rename simple directory to simatic
leds: Kconfig: leds-st1202: Add select for required LEDS_TRIGGER_PATTERN
leds: leds-st1202: Spacing and proofreading editing
leds: leds-st1202: Initialize hardware before DT node child operations
leds: pwm-multicolor: Add check for fwnode_property_read_u32
leds: rgb: leds-qcom-lpg: Add support for 6-bit PWM resolution
leds: Fix LED_OFF brightness race
Revert "leds-pca955x: Remove the unused function pca95xx_num_led_regs()"
leds: st1202: Refactor st1202_led_set() to use !! operator for boolean conversion
dt-bindings: leds: qcom-lpg: Document PM8937 PWM compatible
leds: pca955x: Add HW blink support
leds: pca955x: Optimize probe LED selection
leds: pca955x: Use pointers to driver data rather than I2C client
leds: pca955x: Refactor with helper functions and renaming
dt-bindings: leds: Convert leds-tlc591xx.txt to yaml format
...
Pull LED updates from Lee Jones:
- Allow struct bin_attribute instances to be placed in read-only memory
for enhanced protection
- Fix a memory leak in the cht-wcove driver by using
devm_led_classdev_register()
- Fix an OF node reference leak in the netxbig driver
- Ensure PWM is disabled properly in pwm-multicolor suspend
- Add support for Texas Instruments LP8864, LP8864S, LP8866
LED-backlight drivers
- Add support for STMicroelectronics's LED1202 12-channel LED driver
- Convert LP8860 bindings to YAML format
- Add bindings for the TI LP8864/LP8866 LED drivers
- Add LED1202 LED controller bindings
- Fix path to color definitions in leds-class-multicolor.yaml
- Add pm660l compatible to qcom,spmi-flash-led bindings
- Extend cznic,turris-omnia-leds binding with interrupts property
- Add documentation for the STMicroelectronics LED1202 driver
- Add entry for AAEON UP board FPGA drivers in MAINTAINERS
- Fix a wrong format specifier in the ledtrig-activity driver
- Fix a bug in the lp8860 driver where only half of the EEPROM was
written
* tag 'leds-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (28 commits)
leds: triggers: Constify 'struct bin_attribute'
leds: cht-wcove: Use devm_led_classdev_register() to avoid memory leak
leds: lp8864: Add support for Texas Instruments LP8864, LP8864S, LP8866 LED-backlights
dt-bindings: leds: Convert LP8860 into YAML format
leds: Add LED1202 I2C driver
dt-bindings: leds: Add LED1202 LED Controller
Documentation:leds: Add leds-st1202.rst
leds: pwm-multicolor: Disable PWM when going to suspend
leds: netxbig: Fix an OF node reference leak in netxbig_leds_get_of_pdata()
turris-omnia-mcu-interface.h: Move macro definitions outside of enums
MAINTAINERS: Add entry for AAEON UP board FPGA drivers
leds: Add AAEON UP board LED driver
leds: trigger: netdev: Check offload ability on interface up
leds: turris-omnia: Use uppercase first letter in all comments
leds: turris-omnia: Use dev_err_probe() where appropriate
leds: turris-omnia: Inform about missing LED gamma correction feature in the MCU driver
platform: cznic: turris-omnia-mcu: Inform about missing LED panel brightness change interrupt feature
leds: turris-omnia: Notify sysfs on MCU global LEDs brightness change
leds: turris-omnia: Document driver private structures
dt-bindings: leds: cznic,turris-omnia-leds: Allow interrupts property
...
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@remote-tech.co.uk>
Link: https://lore.kernel.org/r/20241218183401.41687-4-vicentiu.galanopulo@remote-tech.co.uk
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for Texas Instruments LP5569 LED driver.
Texas Instruments LP5569 is 9 channels chip with programmable engines.
It almost a copy of LP5523 with fundamental changes to regs order and
regs content.
Has difference in how the clock is handled and doesn't support detecting
clock time automatically, different handling for selftest and different
scheme for the status regs.
LED chip supports ENGINE and MUX to group LED and run precompiled code
with magic values to run patterns. This is loaded via the sysfs entry
and it's passed as a string of ASCII HEX char.
One some devices using this LED Controller (a NBG7815 Router) it was
found loading big precompiled pattern with up to 96 bytes of code. To
have support for this "extended" scenario, hardcode each engine to
support 4 pages of precompiled pattern (128 bytes of code) and 1 page
for each MUX. This gives plenty of space for any kind precompiled
pattern keeping simple logic for page handling of each engine and mux.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20240626160027.19703-21-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ChromeOS Embedded Controller exposes an LED control command.
Expose its functionality through the leds subsystem.
The LEDs are exposed as multicolor devices.
A hardware trigger, which is active by default, is provided to let the
EC itself take over control over the LED.
The driver is designed to be probed via the cros_ec mfd device.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240613-cros_ec-led-v3-4-500b50f41e0f@weissschuh.net
Signed-off-by: Lee Jones <lee@kernel.org>
The ExpressWire protocol is shared between at least KTD2692 and KTD2801
with slight differences such as timings and the former not having a
defined set of pulses for enabling the protocol (possibly because it
does not support PWM unlike KTD2801). Despite these differences the
ExpressWire handling code can be shared between the two, so in
preparation for adding KTD2801 support introduce a library implementing
this protocol.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20240125-ktd2801-v5-1-e22da232a825@skole.hr
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for LEDs connected to the Intel Cherry Trail Whiskey Cove
PMIC. Charger and general-purpose LEDs are supported. Hardware blinking
is implemented, breathing is not.
This driver was tested with Lenovo Yoga Book notebook.
Changes by Hans de Goede (in response to review of v2):
- Since the PMIC is connected to the battery any changes we make to
the LED settings are permanent, even surviving reboot / poweroff.
Save LED1 register settings on probe() and if auto-/hw-control was
enabled on probe() restore the settings on remove() and shutdown().
- Delay switching LED1 to software control mode to first brightness write.
- Use dynamically allocated drvdata instead of a global drvdata variable.
- Ensure the LED is on when activating blinking.
- Fix CHT_WC_LED_EFF_BREATHING val ((3 << 1) rather then BIT(3)).
Link: https://lore.kernel.org/r/20190212205901.13037-2-jekhor@gmail.com
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Pull LED updates from Lee Jones:
"Removed Drivers:
- HTC ASIC3 LED
New Functionality:
- Provide generic led_get() which can be used by both DT and !DT
platforms
Fix-ups:
- Convert a bunch of I2C subsystem users to the new probing API
- Explicitly provide missing include files
- Make use of led_init_default_state_get() and rid the custom
variants
- Use simplified fwnode_device_is_compatible() API
- Provide some Device Tree additions / adaptions
- Fix some trivial spelling issues
Bug Fixes:
- Prevent device refcount leak during led_put() and of_led_get()
- Clear previous data from temporary led_pwm structure before
processing next child
- Fix Clang's warning about incompatible function types when using
devm_add_action*()"
* tag 'leds-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (41 commits)
leds: Remove ide-disk trigger
dt-bindings: leds: Add disk write/read and usb-host/usb-gadget
Documentation: leds: Correct spelling
dt-bindings: leds: Document Bluetooth and WLAN triggers
leds: Remove asic3 driver
leds: simatic-ipc-leds-gpio: Make sure we have the GPIO providing driver
leds: tca6507: Convert to use fwnode_device_is_compatible()
leds: syscon: Get rid of custom led_init_default_state_get()
leds: pm8058: Get rid of custom led_init_default_state_get()
leds: pca955x: Get rid of custom led_init_default_state_get()
leds: mt6360: Get rid of custom led_init_default_state_get()
leds: mt6323: Get rid of custom led_init_default_state_get()
leds: bcm6358: Get rid of custom led_init_default_state_get()
leds: bcm6328: Get rid of custom led_init_default_state_get()
leds: an30259a: Get rid of custom led_init_default_state_get()
leds: Move led_init_default_state_get() to the global header
leds: Add missing includes and forward declarations in leds.h
leds: is31fl319x: Wrap mutex_destroy() for devm_add_action_or_rest()
leds: turris-omnia: Convert to i2c's .probe_new()
leds: tlc591xx: Convert to i2c's .probe_new()
...
The s3c24xx platform is gone, so the led driver can be
removed as well.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The drivers/leds/rgb subdirectory is relatively fresh, so we move this
new PWM multi-color driver into it.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
By allowing to group multiple monochrome PWM LEDs into multicolor LEDs,
all involved LEDs can be controlled in-sync. This enables using effects
using triggers, etc.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Lukas TimmermannandLee Jones
Linus Torvalds
Dzmitry SankouskiandLee Jones
Alexander SverdlinandLee Jones
Vicentiu GalanopuloandLee Jones
Thomas RichardandLee Jones
Heiko StuebnerandLee Jones
Christian MarangiandLee Jones
Thomas WeißschuhandLee Jones
Duje MihanovićandLee Jones
Patrick RudolphandLee Jones
Samuel HollandandLee Jones
Isai GasparandLee Jones
Lukas BulwahnandLee Jones
Martin KurbanovandLee Jones
Yauhen KharuzhyandLee Jones
Andreas KemnadeandLee Jones
Arnd BergmannandLee Jones
Sven SchwermerandPavel Machek