Add support to get/set embedded sync for both input and output pins.
The DPLL is able to lock on input reference when the embedded sync
frequency is 1 PPS and pulse width 25%. The esync on outputs are more
versatille and theoretically supports any esync frequency that divides
current output frequency but for now support the same that supported on
input pins (1 PPS & 25% pulse).
Note that for the output pins the esync divisor shares the same register
used for N-divided signal formats. Due to this the esync cannot be
enabled on outputs configured with one of the N-divided signal formats.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Prathosh Satish <prathosh.satish@microchip.com>
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250715144633.149156-2-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support to get/set frequency on pins. The frequency for input
pins (references) is computed in the device according this formula:
freq = base_freq * multiplier * (nominator / denominator)
where the base_freq comes from the list of supported base frequencies
and other parameters are arbitrary numbers. All these parameters are
16-bit unsigned integers.
The frequency for output pin is determined by the frequency of
synthesizer the output pin is connected to and divisor of the output
to which is the given pin belongs. The resulting frequency of the
P-pin and the N-pin from this output pair depends on the signal
format of this output pair.
The device supports so-called N-divided signal formats where for the
N-pin there is an additional divisor. The frequencies for both pins
from such output pair are computed:
P-pin-freq = synth_freq / output_div
N-pin-freq = synth_freq / output_div / n_div
For other signal-format types both P and N pin have the same frequency
based only synth frequency and output divisor.
Implement output pin callbacks to get and set frequency. The frequency
setting for the output non-N-divided signal format is simple as we have
to compute just new output divisor. For N-divided formats it is more
complex because by changing of output divisor we change frequency for
both P and N pins. In this case if we are changing frequency for P-pin
we have to compute also new N-divisor for N-pin to keep its current
frequency. From this and the above it follows that the frequency of
the N-pin cannot be higher than the frequency of the P-pin and the
callback must take this limitation into account.
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-13-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement input pin state setting when the DPLL is running in automatic
mode. Unlike manual mode, the DPLL mode switching is not used here and
the implementation uses special priority value (15) to make the given
pin non-selectable.
When the user sets state of the pin as disconnected the driver
internally sets its priority in HW to 15 that prevents the DPLL to
choose this input pin. Conversely, if the pin status is set to
selectable, the driver sets the pin priority in HW to the original saved
value.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-12-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for getting and setting input pin priority. Implement
required callbacks and set appropriate capability for input pins.
Although the pin priority make sense only if the DPLL is running in
automatic mode we have to expose this capability unconditionally because
input pins (references) are shared between all DPLLs where one of them
can run in automatic mode while the other one not.
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-11-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement input pin state setting if the DPLL is running in manual mode.
The driver indicates manual mode if the DPLL mode is one of ref-lock,
forced-holdover, freerun.
Use these modes to implement input pin state change between connected
and disconnected states. When the user set the particular pin as
connected the driver marks this input pin as forced reference and
switches the DPLL mode to ref-lock. When the use set the pin as
disconnected the driver switches the DPLL to freerun or forced holdover
mode. The switch to holdover mode is done if the DPLL has holdover
capability (e.g is currently locked with holdover acquired).
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-10-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enumerate all available DPLL channels and registers a DPLL device for
each of them. Check all input references and outputs and register
DPLL pins for them.
Number of registered DPLL pins depends on configuration of references
and outputs. If the reference or output is configured as differential
one then only one DPLL pin is registered. Both references and outputs
can be also disabled from firmware configuration and in this case
no DPLL pins are registered.
All registrable references are registered to all available DPLL devices
with exception of DPLLs that are configured in NCO (numerically
controlled oscillator) mode. In this mode DPLL channel acts as PHC and
cannot be locked to any reference.
Device outputs are connected to one of synthesizers and each synthesizer
is driven by some DPLL channel. So output pins belonging to given output
are registered to DPLL device that drives associated synthesizer.
Finally add kworker task to monitor async changes on all DPLL channels
and input pins and to notify about them DPLL core. Output pins are not
monitored as their parameters are not changed asynchronously by the
device.
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-9-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for reading of DPLL types and optional pin properties from
the system firmware (DT, ACPI...).
The DPLL types are stored in property 'dpll-types' as string array and
possible values 'pps' and 'eec' are mapped to DPLL enums DPLL_TYPE_PPS
and DPLL_TYPE_EEC.
The pin properties are stored under 'input-pins' and 'output-pins'
sub-nodes and the following ones are supported:
* reg
integer that specifies pin index
* label
string that is used by driver as board label
* connection-type
string that indicates pin connection type
* supported-frequencies-hz
array of u64 values what frequencies are supported / allowed for
given pin with respect to hardware wiring
Do not blindly trust system firmware and filter out frequencies that
cannot be configured/represented in device (input frequencies have to
be factorized by one of the base frequencies and output frequencies have
to divide configured synthesizer frequency).
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-8-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Several configuration parameters will remain constant at runtime,
so we can load them during probe to avoid excessive reads from
the hardware.
Read the following parameters from the device during probe and store
them for later use:
* enablement status and frequencies of the synthesizers and their
associated DPLL channels
* enablement status and type (single-ended or differential) of input pins
* associated synthesizers, signal format, and enablement status of
outputs
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-7-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Microchip Azurite ZL3073x represents chip family providing DPLL
and optionally PHC (PTP) functionality. The chips can be connected
be connected over I2C or SPI bus.
They have the following characteristics:
* up to 5 separate DPLL units (channels)
* 5 synthesizers
* 10 input pins (references)
* 10 outputs
* 20 output pins (output pin pair shares one output)
* Each reference and output can operate in either differential or
single-ended mode (differential mode uses 2 pins)
* Each output is connected to one of the synthesizers
* Each synthesizer is driven by one of the DPLL unit
The device uses 7-bit addresses and 8-bits values. It exposes 8-, 16-,
32- and 48-bits registers in address range <0x000,0x77F>. Due to 7bit
addressing, the range is organized into pages of 128 bytes, with each
page containing a page selector register at address 0x7F.
For reading/writing multi-byte registers, the device supports bulk
transfers.
Add basic functionality to access device registers, probe functionality
both I2C and SPI cases and add devlink support to provide info and
to set clock ID parameter.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-6-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.14-rc8).
Conflict:
tools/testing/selftests/net/Makefile
03544faad7 ("selftest: net: add proc_net_pktgen")
3ed61b8938 ("selftests: net: test for lwtunnel dst ref loops")
tools/testing/selftests/net/config:
85cb3711ac ("selftests: net: Add test cases for link and peer netns")
3ed61b8938 ("selftests: net: test for lwtunnel dst ref loops")
Adjacent commits:
tools/testing/selftests/net/Makefile
c935af429e ("selftests: net: add support for testing SO_RCVMARK and SO_RCVPRIORITY")
355d940f4d ("Revert "selftests: Add IPv6 link-local address generation tests for GRE devices."")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In case of returning 1 from xa_alloc_cyclic() (wrapping) ERR_PTR(1) will
be returned, which will cause IS_ERR() to be false. Which can lead to
dereference not allocated pointer (pin).
Fix it by checking if err is lower than zero.
This wasn't found in real usecase, only noticed. Credit to Pierre.
Fixes: 97f265ef7f ("dpll: allocate pin ids in cycle")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow driver expose quality level of the clock it is
running, introduce a new netlink attr with enum to carry it to the
userspace. Also, introduce an op the dpll netlink code calls into the
driver to obtain the value.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20241030081157.966604-2-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In scenario where pin is registered with multiple parent pins via
dpll_pin_on_pin_register(..), all belonging to the same dpll device.
A second call to dpll_pin_on_pin_unregister(..) would cause a call trace,
as it tries to use already released registration resources (due to fix
introduced in b446631f35). In this scenario pin was registered twice,
so resources are not yet expected to be release until each registered
pin/pin pair is unregistered.
Currently, the following crash/call trace is produced when ice driver is
removed on the system with installed E810T NIC which includes dpll device:
WARNING: CPU: 51 PID: 9155 at drivers/dpll/dpll_core.c:809 dpll_pin_ops+0x20/0x30
RIP: 0010:dpll_pin_ops+0x20/0x30
Call Trace:
? __warn+0x7f/0x130
? dpll_pin_ops+0x20/0x30
dpll_msg_add_pin_freq+0x37/0x1d0
dpll_cmd_pin_get_one+0x1c0/0x400
? __nlmsg_put+0x63/0x80
dpll_pin_event_send+0x93/0x140
dpll_pin_on_pin_unregister+0x3f/0x100
ice_dpll_deinit_pins+0xa1/0x230 [ice]
ice_remove+0xf1/0x210 [ice]
Fix by adding a parent pointer as a cookie when creating a registration,
also when searching for it. For the regular pins pass NULL, this allows to
create separated registration for each parent the pin is registered with.
Fixes: b446631f35 ("dpll: fix dpll_xa_ref_*_del() for multiple registrations")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240424101636.1491424-1-arkadiusz.kubalewski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, if there are multiple registrations of the same pin on the
same dpll device, following warnings are observed:
WARNING: CPU: 5 PID: 2212 at drivers/dpll/dpll_core.c:143 dpll_xa_ref_pin_del.isra.0+0x21e/0x230
WARNING: CPU: 5 PID: 2212 at drivers/dpll/dpll_core.c:223 __dpll_pin_unregister+0x2b3/0x2c0
The problem is, that in both dpll_xa_ref_dpll_del() and
dpll_xa_ref_pin_del() registration is only removed from list in case the
reference count drops to zero. That is wrong, the registration has to
be removed always.
To fix this, remove the registration from the list and free
it unconditionally, instead of doing it only when the ref reference
counter reaches zero.
Fixes: 9431063ad3 ("dpll: core: Add DPLL framework base functions")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera
Arkadiusz Kubalewski
Simon Horman
Paolo Abeni
Michal Swiatkowski
Jiasheng Jiang
Jiri Pirko
Chen Ni
Prasad Pandit
Jakub Kicinski