Pull xtensa updates from Max Filippov:
- a few one-liner cleanups
* tag 'xtensa-20250126' of https://github.com/jcmvbkbc/linux-xtensa:
xtensa/simdisk: Use str_write_read() helper in simdisk_transfer()
xtensa: Remove zero-length alignment array
xtensa: annotate dtb_start variable as static __initdata
The 'dtb_start' variable is only used within arch/xtensa/kernel/setup.c.
Mark it as 'static'.
It is only used by parse_tag_fdt() and init_arch(), both of which are
annotated as __init. Therefore, dtb_start can be annotated as __initdata,
so it will discarded after boot.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Message-Id: <20240918031537.588965-1-masahiroy@kernel.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
__pa() is only intended to be used for linear map addresses and using
it for initial_boot_params which is in fixmap for arm64 will give an
incorrect value. Hence save the physical address when it is known at
boot time when calling early_init_dt_scan for arm64 and use it at kexec
time instead of converting the virtual address using __pa().
Note that arm64 doesn't need the FDT region reserved in the DT as the
kernel explicitly reserves the passed in FDT. Therefore, only a debug
warning is fixed with this change.
Reported-by: Breno Leitao <leitao@debian.org>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Usama Arif <usamaarif642@gmail.com>
Fixes: ac10be5cdb ("arm64: Use common of_kexec_alloc_and_setup_fdt()")
Link: https://lore.kernel.org/r/20241023171426.452688-1-usamaarif642@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Add Kconfig symbol, asm/mtd-xip.h header and define related macros:
xip_cpu_idle, xip_irqpending, xip_currtime and xip_elapsed_since.
Append .xiptext to the vectors when separate vectors are configured
because otherwise they are appended to the data and data may not even be
executable in XIP configuration.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Memory attached to instruction bus of the xtensa CPU is only accessible
for a limited subset of opcodes. Other opcodes generate an exception
with the load/store error cause code. This property complicates use of
such systems. Provide a handler that recognizes and transparently fixes
such exceptions. The following opcodes are recognized when used outside
of FLIX bundles: l32i, l32i.n, l16ui, l16si, l8ui.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
There may be other users for the early traps besides KASAN. Move call to
the early_trap_init from kasan_early_init. Protect init_exc_table
initializer with ifdef to make sure it builds on noMMU configurations.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add 'trax' to the list of CPU features when xtensa core is configured
with TRAX.
Add 'perf' to the list of CPU features when xtensa core is configured
with perf counters and show the number of configured perf counters.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Instead of using xtensa-specific platform_halt and platform_power_off
callbacks use do_kernel_power_off in the machine_halt and
machine_power_off and reimplement existing platform_halt and
platform_power_off users with register_sys_off_handler.
Drop platform_halt and platform_power_off declarations and default
implementations.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Instead of using xtensa-specific platform_restart callback use
do_kernel_restart in the machine_restart implementation and reimplement
existing platform_restart users with register_restart_handler.
Drop platform_restart declaration and default implementation.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Whether xtensa cores start from primary or secondary reset vector is
configurable and may be chosen by board designer or controlled at
runtime. When secondary reset vector is unused its location in memory
may not be writable.
Make secondary reset vector support conditional and don't build and load
secondary reset vector code when it is disabled.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The strlcpy should not be used because it doesn't limit the source
length. So that it will lead some potential bugs.
But the strscpy doesn't require reading memory from the src string
beyond the specified "count" bytes, and since the return value is
easier to error-check than strlcpy()'s. In addition, the implementation
is robust to the string changing out from underneath it, unlike the
current strlcpy() implementation.
Thus, replace strlcpy with strscpy.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Message-Id: <20211220084756.955307-1-wangborong@cdjrlc.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Introduce asm/sections.h and move section declarations to this header
from setup.c. Assign section symbols char array type uniformly and drop
address operator from section symbol references in code.
Sort headers in setup.c while at it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
There's no need in window overflow/underflow/alloca exception handlers
or window spill code when neither kernel nor userspace support windowed
registers. Don't build or link it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
CONFIG_OF can be set by a randconfig or by a user -- without setting the
early flattree option (OF_EARLY_FLATTREE). This causes build errors.
However, if randconfig or a user sets USE_OF in the Xtensa config,
the right kconfig symbols are set to fix the build.
Fixes these build errors:
../arch/xtensa/kernel/setup.c:67:19: error: ‘__dtb_start’ undeclared here (not in a function); did you mean ‘dtb_start’?
67 | void *dtb_start = __dtb_start;
| ^~~~~~~~~~~
../arch/xtensa/kernel/setup.c: In function 'xtensa_dt_io_area':
../arch/xtensa/kernel/setup.c:201:14: error: implicit declaration of function 'of_flat_dt_is_compatible'; did you mean 'of_machine_is_compatible'? [-Werror=implicit-function-declaration]
201 | if (!of_flat_dt_is_compatible(node, "simple-bus"))
../arch/xtensa/kernel/setup.c:204:18: error: implicit declaration of function 'of_get_flat_dt_prop' [-Werror=implicit-function-declaration]
204 | ranges = of_get_flat_dt_prop(node, "ranges", &len);
../arch/xtensa/kernel/setup.c:204:16: error: assignment to 'const __be32 *' {aka 'const unsigned int *'} from 'int' makes pointer from integer without a cast [-Werror=int-conversion]
204 | ranges = of_get_flat_dt_prop(node, "ranges", &len);
| ^
../arch/xtensa/kernel/setup.c: In function 'early_init_devtree':
../arch/xtensa/kernel/setup.c:228:9: error: implicit declaration of function 'early_init_dt_scan'; did you mean 'early_init_devtree'? [-Werror=implicit-function-declaration]
228 | early_init_dt_scan(params);
../arch/xtensa/kernel/setup.c:229:9: error: implicit declaration of function 'of_scan_flat_dt' [-Werror=implicit-function-declaration]
229 | of_scan_flat_dt(xtensa_dt_io_area, NULL);
xtensa-elf-ld: arch/xtensa/mm/mmu.o:(.text+0x0): undefined reference to `xtensa_kio_paddr'
Fixes: da844a8177 ("xtensa: add device trees support")
Fixes: 6cb971114f ("xtensa: remap io area defined in device tree")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Increment *pos in the cpuinfo_op.next to fix the following warning
triggered by cat /proc/cpuinfo:
seq_file: buggy .next function c_next did not update position index
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Pull xtensa updates from Max Filippov:
- reorganize exception vectors placement
- small cleanups (drop unused functions/headers/defconfig entries,
spelling fixes)
* tag 'xtensa-20200206' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: ISS: improve simcall assembly
xtensa: reorganize vectors placement
xtensa: separate SMP and XIP support
xtensa: move fast exception handlers close to vectors
arch/xtensa: fix Kconfig typos for HAVE_SMP
xtensa: clean up optional XCHAL_* definitions
xtensa: drop unused function fast_coprocessor_double
xtensa: drop empty platform_* functions from platforms
xtensa: clean up platform headers
xtensa: drop set_except_vector declaration
xtensa: configs: Cleanup old Kconfig IO scheduler options
Allow vectors to be either merged into the kernel .text or put at a
fixed virtual address independently of XIP option. Drop option that
puts vectors at a fixed offset from the kernel text. Add choice to
Kconfig.
Vectors at fixed virtual address may be useful for XIP-aware MTD support
and for noMMU configurations with available IRAM. Configurations without
VECBASE register must put their vectors at specific locations regardless
of the selected option. All other configurations should happily use
merged vectors.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
On XIP kernels it makes sense to have exception vectors and fast
exception handlers together (in a fast memory). In addition, with MTD
XIP support both vectors and fast exception handlers must be outside of
the FLASH.
Add section .exception.text and move fast exception handlers to it.
Put it together with vectors when vectors are outside of the .text.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
XIP (eXecute In Place) kernel image is the image that can be run
directly from ROM, using RAM only for writable data.
XIP xtensa kernel differs from regular xtensa kernel in the following
ways:
- it has exception/IRQ vectors merged into text section. No vectors
relocation takes place at kernel startup.
- .data/.bss location must be specified in the kernel configuration,
its content is copied there in the _startup function.
- .init.text is merged with the rest of text and is executed from ROM.
- when MMU is used the virtual address where the kernel will be mapped
must be specified in the kernel configuration. It may be in the KSEG
or in the KIO, __pa macro is adjusted to be able to handle both.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The xtensa free_initrd_mem() verifies that initrd is mapped and then
frees its memory using free_reserved_area().
The initrd is considered mapped when its memory was successfully reserved
with mem_reserve().
Resetting initrd_start to 0 in case of mem_reserve() failure allows to
switch to generic free_initrd_mem() implementation.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Message-Id: <1563977432-8376-1-git-send-email-rppt@linux.ibm.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
ITLB entry modifications must be followed by the isync instruction
before the new entries are possibly used. cpu_reset lacks one isync
between ITLB way 6 initialization and jump to the identity mapping.
Add missing isync to xtensa cpu_reset.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Linus Torvalds
Masahiro YamadaandMax Filippov
Usama ArifandRob Herring (Arm)
Arnd BergmannandGreg Kroah-Hartman
Jason WangandMax Filippov
Randy DunlapandMax Filippov
Joe PerchesandLinus Torvalds
Mike RapoportandLinus Torvalds
Arvind SankarandGreg Kroah-Hartman