The hwmon sysfs naming convention uses
temp[1-*]_input for temperature channels.
Documentation/hwmon/sy7636a-hwmon.rst currently documents
temp0_input, while the driver uses the standard hwmon
temperature channel interface.
Update the documentation to use temp1_input.
Signed-off-by: Chen-Shi-Hong <eric039eric@gmail.com>
Link: https://lore.kernel.org/r/20260514154108.1937-1-eric039eric@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add pmbus support for Sony APS-379 power supplies. There are a few PMBUS
commands that return data that is undocumented/invalid so these need to
be rejected with -ENXIO. The READ_VOUT command returns data in linear11
format instead of linear16 so we need to workaround this.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20260410012414.2818829-3-chris.packham@alliedtelesis.co.nz
[groeck: Dropped empty line from documentation; added module name to Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There are several places in yogafan.rst where it appears that lines
are meant to be presented on their own but instead they are strung
together due to the lack of markups. Fix these issues by:
- using bullets where needed
- indenting continuation lines of bulleted items
- using a table where appropriate
- using a literal block where appropriate
Fixes: c67c248ca4 ("hwmon: (yogafan) Add support for Lenovo Yoga/Legion fan monitoring")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20260407052317.2097791-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a blank line between the License and heading lines to prevent a
documentation build warning:
Documentation/hwmon/yogafan.rst:2: WARNING: Explicit markup ends without
a blank line; unexpected unindent. [docutils]
Fixes: c67c248ca4 ("hwmon: (yogafan) Add support for Lenovo Yoga/Legion fan monitoring")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20260330214624.3781789-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver provides fan speed monitoring for Lenovo Yoga, Legion, and
IdeaPad laptops by interfacing with the Embedded Controller (EC) via ACPI.
To address low-resolution sampling in Lenovo EC firmware, a Rate-Limited
Lag (RLLag) filter is implemented. The filter ensures a consistent physical
curve regardless of userspace polling frequency.
Hardware identification is performed via DMI-based quirk tables, which
map specific ACPI object paths and register widths (8-bit vs 16-bit)
deterministically.
Signed-off-by: Sergio Melas <sergiomelas@gmail.com>
Link: https://lore.kernel.org/r/20260327221602.18832-1-sergiomelas@gmail.com
[groeck: Dropped double empty line in Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add I2C device IDs for Renesas RAA228942 and RAA228943.
At the Linux PMBus hwmon interface level currently supported by this
driver, these devices are compatible with the existing 2-rail non-TC
controllers, so devicetree will use fallback compatibles and no
dedicated OF match entries are needed.
Signed-off-by: Dawei Liu <dawei.liu.jy@renesas.com>
Link: https://lore.kernel.org/r/20260325090208.857-3-dawei.liu.jy@renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the ITE IT8689E Super I/O chip. The IT8689E supports
newer autopwm, 12mV ADC, 16-bit fans, six fans, six PWM channels,
PWM frequency 2, six temperature inputs, AVCC3, temperature offset,
and fan on/off control.
Give it8689 its own GPIO configuration block in it87_find() rather
than sharing the it8620/it8628 block. The shared block reads
IT87_SIO_PINX2_REG and either marks IN3 as internal AVCC or skips
IN9. Because it8689 declares FEAT_AVCC3, IN9 is already marked as
always-internal before the GPIO block is reached; applying the PINX2
check would either create duplicate AVCC labels on IN3 and IN9 or
incorrectly skip IN9.
Also update Documentation/hwmon/it87.rst and drivers/hwmon/Kconfig to
document the newly supported chip.
Signed-off-by: Markus Hoffmann <markus@thehoffs.at>
Link: https://lore.kernel.org/r/20260322103301.18112-1-markus@thehoffs.at
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add hardware monitoring support for the LattePanda Sigma SBC
(DFRobot, ITE IT8613E EC). The driver reads fan speed and
temperatures via direct port I/O, as the BIOS disables the
ACPI EC interface.
Signed-off-by: Mariano Abad <weimaraner@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adm1177 driver exposes the current alert threshold through
hwmon_curr_max_alarm. This violates the hwmon sysfs ABI, where
*_alarm attributes are read-only status flags and writable thresholds
must use currN_max.
The driver also stores the threshold internally in microamps, while
currN_max is defined in milliamps. Convert the threshold accordingly
on both the read and write paths.
Widen the cached threshold and related calculations to 64 bits so
that small shunt resistor values do not cause truncation or overflow.
Also use 64-bit arithmetic for the mA/uA conversions, clamp writes
to the range the hardware can represent, and propagate failures from
adm1177_write_alert_thr() instead of silently ignoring them.
Update the hwmon documentation to reflect the attribute rename and
the correct units returned by the driver.
Fixes: 09b08ac9e8 ("hwmon: (adm1177) Add ADM1177 Hot Swap Controller and Digital Power Monitor driver")
Signed-off-by: Sanman Pradhan <psanman@juniper.net>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20260325051246.28262-1-sanman.pradhan@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hwmon sysfs ABI expects tempN_crit_hyst to report the temperature at
which the critical condition clears, not the hysteresis delta from the
critical limit.
The peci cputemp driver currently returns tjmax - tcontrol for
crit_hyst_type, which is the hysteresis margin rather than the
corresponding absolute temperature.
Return tcontrol directly, and update the documentation accordingly.
Fixes: bf3608f338 ("hwmon: peci: Add cputemp driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sanman Pradhan <psanman@juniper.net>
Link: https://lore.kernel.org/r/20260323002352.93417-2-sanman.pradhan@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Guenter Roeck:
"New PMBus drivers:
- HiTRON HAC300S power supply
- Monolithic MP5926 Hot-Swap Controller
- STEF48H28 hot-swap controller
Support for new chips in existing drivers
- Support for Pro WS TRX50-SAGE WIFI A and ROG MAXIMUS X HERO
(asus-ec-sensors)
- Support for Dell OptiPlex 7080 (dell-smm)
- Support for F81968 (f71882fg)
- Support for Micro PC 2 (gpd-fan)
- New customer ID for ASRock Z590 Taichi (nct6683)
- Support for ASUS Pro WS WRX90E-SAGE SE (nct6775)
- Support for SHT85 (sht3x)
- Support for P3T1035 and P3T2030 (tmp108)
Bug fixes:
- Revert "fix" for UAF which didn't fix a UAF but introduced a race
condition resulting in a NULL pointer crash (ibmpex)
- Fix failure to instantiate driver if the chip is configured for VID
mode (pmbus/mpq8785)
- Use READ/WRITE_ONCE to avoid compiler optimization induced race
(max16065)
- Resource leak fixes (nct7363, emc2305)
Other notable changes:
- Support for temperature limit thresholds (cros_ec)
- Add TjMax for Silvermont through Tremont Atoms (coretemp)
Various other minor improvements"
* tag 'hwmon-for-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (42 commits)
hwmon: (pmbus/mpq8785) fix VOUT_MODE mismatch during identification
Revert "hwmon: (ibmpex) fix use-after-free in high/low store"
hwmon: (max16065) Use READ/WRITE_ONCE to avoid compiler optimization induced race
hwmon: (nct6775) use sysfs_emit instead of sprintf
hwmon: pmbus: fix table in STEF48H28 documentation
hwmon: Add support for HiTRON HAC300S PSU
dt-bindings: trivial-devices: Add hitron,hac300s
hwmon: (cros_ec) Add support for temperature thresholds
hwmon: (cros_ec) Move temperature channel params to a macro
hwmon: (cros_ec) Add support for fan target speed
hwmon: (cros_ec) Split up supported features in the documentation
hwmon: (tmp108) Add P3T1035 and P3T2030 support
hwmon: (tmp108) Add support for P3T1035 and P3T2030
dt-bindings: hwmon: ti,tmp108: Add P3T1035,P3T2030
hwmon: pmbus: add support for STEF48H28
dt-bindings: hwmon: add STEF48H28
hwmon: (nct7363) Fix a resource leak in nct7363_present_pwm_fanin
hwmon: (emc2305) Fix a resource leak in emc2305_of_parse_pwm_child
hwmon: (gpd-fan) add support for Micro PC 2
hwmon: (coretemp) Add TjMax for Silvermont through Tremont Atoms
...
"make htmldocs" reports build errors/warnings:
Documentation/hwmon/stef48h28.rst:45: ERROR: Missing matching underline for section title overline.
=========================================================
in1_label "vin".
in1_input Measured voltage. From READ_VIN register. [docutils]
Documentation/hwmon/stef48h28.rst:73: WARNING: Title underline too short.
temp2_input Measured temperature. From READ_TEMPERATURE_2 register.
========================================================= [docutils]
Fix the table overline/underline line lengths and convert it to
a 2-column table.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20260128002200.1665941-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
