Some 3 pole connectors report impedance greater than threshold of
1000Ohm. Thus, da7219 reports them as LINEOUT.
Adding the SND_JACK_LINEOUT type so that we don't fail to detect
any 3 pole jack type.
Also, changing
SND_JACK_HEADPHONE | SND_JACK_MICROPHONE -> SND_JACK_HEADSET
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
alsa_conformance_test -C hw:0,4 -p 1024 --debug
would sometime show:
TIME_DIFF(s) HW_LEVEL READ RATE
0.000095970 1024 1024 10670001.041992
0.042609555 1024 2048 24032.168372
0.021330364 1024 3072 48006.681930
0.021339559 1024 4096 47985.996337
The issue is that in dma pointer function we can have stale value
of the register for current descriptor of channel.
The register retains the number of the last descriptor that
was transferred.
Fix ensures that we report position, 0, till the one period worth of
data is transferred. After one period of data, in handler of period
completion interrupt we update the config and correct value of descriptor
starts reflecting.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If capture and playback are started on different channel (I2S/BT)
there is a possibilty that channel information passed from machine driver
is overwritten before the configuration is done in dma driver.
Example:
113.597588: cz_max_startup: ---playback sets BT channel
113.597694: cz_dmic1_startup: ---capture sets I2S channel
113.597979: acp_dma_hw_params: ---configures capture for I2S channel
113.598114: acp_dma_hw_params: ---configures playback for I2S channel
This is fixed by having 2 separate instance for playback and capture.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HW register descriptions says:
"DMA Channel Reset...Software must confirm that this bit is
cleared before reprogramming any of the channel configuration registers."
There could be cases where dma stop errored out leaving dma channel
in reset state. We need to ensure that before the start of another dma,
channel is out of the reset state.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
25Mhz MCLK which was earlier used was of spread type.
Thus, we were not getting accurate rate. The 48Mhz system
clk is of non-spread type and we are changing to it to get
accurate rate.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We support dual channel, 48Khz. This constraint was set only for
da7219. It is being extended to DMIC and MAX98357a.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP->SYSMEM DMA happens at every I2S->SYSMEM period
completion. Thus, there is delay of x frames till
I2S->SYSMEM reaches a period length. This delay is
communicated to user space.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give position on ACP->SYSMEM DMA channel for
the number of bytes that have been transferred on
the basis of current descriptor under service.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In capture case we don't want ACP to SYSMEM dma
to be circular. This is because if an in place DSP
filter is applied to captured output then circular DMA
can overwrite the filter value with stale data.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes
sound/soc/amd/acp-da7219-max98357a.c: In function 'cz_probe':
sound/soc/amd/acp-da7219-max98357a.c:367:3: warning: 'ret' may
be used uninitialized in this function [-Wmaybe-uninitialized]
dev_err(&pdev->dev, "Failed to register regulator: %d\n",
ret);
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DA7219 for our platform need to be configured for 1.8V.
Hence, we add a volatge regulator with supplies
of 1.8V in the machine driver.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Having interrupts enabled for ACP<->SYSMEM DMA transfer, we are in
for an interrupt storm.
For both playback and capture interrupts should be enabled for
I2S<->ACP DMA.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Earlier, ch1 was used to define ACP-SYSMEM transfer and ch2 for
ACP-I2S transfer. With recent patches ch1 is used to define channel
order number 1 and ch2 as channel order number 2. Thus,
Playback:
ch1:SYSMEM->ACP
ch2:ACP->I2S
Capture:
ch1:I2S->ACP
ch1:ACP->SYSMEM
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the I2S channel names are fixed, and DMA data flow order is
consistent (ch1 then ch2), we can simplify channel start order:
start the upstream channel and then the downstream channel for both
playback and capture cases.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer() callback gets its value by reading the I2S BYTE_COUNT
register. This is a 64-bit runnning transaction counter. If a
transaction was aborted in the middle of a sample buffer, the counter will
stop counting on a number divisible by the buffer size. Since we actually
use it as a pointer into an aligned buffer, however, we do want to ensure
that it always starts at a number divisible by the buffer size when
starting a transaction, hence we reset it whenever starting a transaction.
To accomplish this, it wasn't necessary to zero bytescount at the
termination of each transaction, so remove this unnecessary code.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On capture, audio data is first copied from I2S to ACP memory, and then
from ACP to SYSRAM. The I2S_TO_ACP_DMA interrupt fires on every sample
transferred from I2S to ACP memory. That is it fires ~48000 times per
second when capturing @ 48 kHz. Since we don't do anything on this
interrupt anyway, disable it to save quite a few unnecessary interrupts.
The real "work" (calling snd_pcm_period_elapsed()) is done when transfer
from ACP to SYSRAM is complete.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On capture, audio data is first copied from I2S to ACP memory, and then
to SYSRAM. For each step the channel number increases, so the names in
the driver were wrong.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is always correct to subtract out the starting bytescount value. Even
in the case of 2^64 byte rollover (292 Million Years in the future
@ 48000 Hz) the math still works out.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6b116dfb46 ("ASoC: AMD: make channel 1 dma as circular") made
both channels circular, so this comment and logic no longer applies. Always
stop ch2 (the channel closest to the output) before ch1. This ensures
that the downstream circular DMA channel does not continue to play/capture
repeated samples after the upstream circular DMA channel has already
stopped.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ST/CZ SoC have 2 channels for capture in the I2SSP path.
The DMA though these channels is done using the same dma
descriptors.
We configure the channel and enable it on the basis of
channel selected by machine driver. Machine driver knows
which codec sits on which channel and thus sends the information
to dma driver.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a correction to match acutal hardware configuration.
The hardware configuration looks like:
I2S_BT -> SPK(Max) + DMIC(Adau)
I2S_SP -> DA7219 Headset
No actual products have been shipped with previous configuration.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix crash in those platforms whose machine driver does not expose
platform_info. For those platforms we rely on default value and
select I2SSP channel.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown
Akshu Agrawal
Mukunda, Vijendar
Daniel Kurtz