This patch fixes the debugging printks. Use pr_cont, so that the lines are
not broken up. Use printk when starting a new line (a long string of
pr_cont's without any printks causes missing characters in the console
output on sparc).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
This is a simple optimization for fifo waiting that improves scrolling
performance by 5%. If the queue has more free entries that what we
consume, we can skip the costly register read next time.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reading the registers without waiting for engine idle returns
unpredictable values. These unpredictable values result in display
corruption - if atyfb_imageblit reads the content of DP_PIX_WIDTH with the
bit DP_HOST_TRIPLE_EN set (from previous invocation), the driver would
never ever clear the bit, resulting in display corruption.
We don't want to wait for idle because it would degrade performance, so
this patch modifies the driver so that it never reads accelerator
registers.
HOST_CNTL doesn't have to be read, we can just write it with
HOST_BYTE_ALIGN because no other part of the driver cares if
HOST_BYTE_ALIGN is set.
DP_PIX_WIDTH is written in the functions atyfb_copyarea and atyfb_fillrect
with the default value and in atyfb_imageblit with the value set according
to the source image data.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The code for manual bit triple is not endian-clean. It builds the variable
"hostdword" using byte accesses, therefore we must read the variable with
"le32_to_cpu".
The patch also enables (hardware or software) bit triple only if the image
is monochrome (image->depth). If we want to blit full-color image, we
shouldn't use the triple code.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
On Sun Ultra 5, it happens that the dot clock is not set up properly for
some videomodes. For example, if we set the videomode "r1024x768x60" in
the firmware, Linux would incorrectly set a videomode with refresh rate
180Hz when booting (suprisingly, my LCD monitor can display it, although
display quality is very low).
The reason is this: Older mach64 cards set the divider in the register
VCLK_POST_DIV. The register has four 2-bit fields (the field that is
actually used is specified in the lowest two bits of the register
CLOCK_CNTL). The 2 bits select divider "1, 2, 4, 8". On newer mach64 cards,
there's another bit added - the top four bits of PLL_EXT_CNTL extend the
divider selection, so we have possible dividers "1, 2, 4, 8, 3, 5, 6, 12".
The Linux driver clears the top four bits of PLL_EXT_CNTL and never sets
them, so it can work regardless if the card supports them. However, the
sparc64 firmware may set these extended dividers during boot - and the
mach64 driver detects incorrect dot clock in this case.
This patch makes the driver read the additional divider bit from
PLL_EXT_CNTL and calculate the initial refresh rate properly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
radeonfb_pci_suspend() is never called in atomic context.
radeonfb_pci_suspend() is only set as ".suspend" in struct pci_driver.
This function is not called in atomic context.
Despite never getting called from atomic context, radeonfb_pci_suspend()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep()
and usleep_range() to avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
aty128_set_suspend() is never called in atomic context.
The call chains ending up at aty128_set_suspend() are:
[1] aty128_set_suspend() <- aty128_pci_suspend()
[2] aty128_set_suspend() <- aty128_do_resume() <- aty128_pci_resume()
[3] aty128_set_suspend() <- aty128_do_resume() <- aty128_early_resume()
aty128_pci_suspend() is set as ".suspend" in struct pci_driver.
aty128_pci_resume() is set as ".resume" in struct pci_driver.
aty128_early_resume() is never called.
These functions are not called in atomic context.
Despite never getting called from atomic context, aty128_set_suspend()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
There is a missing indentation following an if statement, fix this.
Detected by Coccinelle:
drivers/video/fbdev/aty/mach64_ct.c:183:2-15: code aligned with
following code on line 184
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
When the linux kernel is build with (typical kernel ship with Debian
installer):
CONFIG_FB=y
CONFIG_FB_OF=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_FB_RADEON=m
The offb driver takes precedence over module radeonfb. It is then
impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007)
[ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref]
[ 96.551531] radeonfb (0000:00:10.0): cannot request region 0.
[ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16
This patch reproduce the behavior of the module radeon, so as to make it
possible to load radeonfb when offb is first loaded, see
commit a56f7428d7 ("drm/radeon: Add early unregister of firmware fb's").
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Link: https://bugs.debian.org/826629#57
Link: https://bugzilla.kernel.org/show_bug.cgi?id=119741
Suggested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
do_gettimeofday() is deprecated and a bit clumsy. This changes
radeon_probe_pll_params() over to using ktime_get() with monotonic
times. There is no need to check for negative values any more
since the monotonic clocksource cannot go backwards, but I'm
adding a check for zero-division in case of a bad clocksource.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"There is nothing really major here (though removal of the dead igafb
driver stands out in diffstat).
Summary:
- convert timers to use timer_setup() (Kees Cook, Thierry Reding)
- fix panels support on iMX boards in mxsfb driver (Stefan Agner)
- fix timeout on EDID read in udlfb driver (Ladislav Michl)
- add missing modes to fix out of bounds access in controlfb driver
(Geert Uytterhoeven)
- update initialisation paths in sa1100fb driver to be more robust
(Russell King)
- fix error handling path of ->probe method in au1200fb driver
(Christophe JAILLET)
- fix handling of cases when either panel or crt is defined in
sm501fb driver (Sudip Mukherjee, Colin Ian King)
- add ability to the Goldfish FB driver to be recognized by OS via DT
(Aleksandar Markovic)
- structures constifications (Bhumika Goyal)
- misc fixes (Allen Pais, Gustavo A. R. Silva, Dan Carpenter)
- misc cleanups (Colin Ian King, Himanshu Jha, Markus Elfring)
- remove dead igafb driver"
* tag 'fbdev-v4.15' of git://github.com/bzolnier/linux: (42 commits)
OMAPFB: prevent buffer underflow in omapfb_parse_vram_param()
video: fbdev: sm501fb: fix potential null pointer dereference on fbi
fbcon: Initialize ops->info early
video: fbdev: Convert timers to use timer_setup()
video: fbdev: pxa3xx_gcu: Convert timers to use timer_setup()
fbdev: controlfb: Add missing modes to fix out of bounds access
video: fbdev: sis_main: mark expected switch fall-throughs
video: fbdev: cirrusfb: mark expected switch fall-throughs
video: fbdev: aty: radeon_pm: mark expected switch fall-throughs
video: fbdev: sm501fb: mark expected switch fall-through in sm501fb_blank_crt
video: fbdev: intelfb: remove redundant variables
video/fbdev/dnfb: Use common error handling code in dnfb_probe()
sm501fb: suspend and resume fb if it exists
sm501fb: unregister framebuffer only if registered
sm501fb: deallocate colormap only if allocated
video: goldfishfb: Add support for device tree bindings
Documentation: Add device tree binding for Goldfish FB driver
video: udlfb: Fix read EDID timeout
video: fbdev: remove dead igafb driver
video: fbdev: mxsfb: fix pixelclock polarity
...
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't populate the read-only const array post_divs on the stack,
instead make it static. Makes the object code smaller by 90 bytes:
Before:
text data bss dec hex filename
40231 8584 896 49711 c22f radeon_base.o
After:
text data bss dec hex filename
39914 8744 960 49618 c1d2 radeon_base.o
(gcc version 7.2.0, x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Don't populate the const arrays ragepro_tbl and ragexl_tbl on the stack,
instead make them static. Makes the object code smaller by over 380 bytes:
Before:
text data bss dec hex filename
41089 10592 768 52449 cce1 atyfb_base.o
After:
text data bss dec hex filename
40544 10752 768 52064 cb60 atyfb_base.o
(gcc version 7.2.0, x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Make these const as they are only passed to a const argument of the
function fb_find_mode.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct fb_videomode s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
identifier match.s;
expression list[5] es;
position ref.p;
@@
fb_find_mode(es,&s@p,...)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct fb_videomode s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Add const to bin_attribute structures as they are only passed to the
functions sysfs_{remove/create}_bin_file or
device_{remove/create}_bin_file. The corresponding arguments are of
type const, so declare the structures to be const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
11525 2048 8 13581 350d video/fbdev/aty/aty128fb.o
File size after adding 'const':
text data bss dec hex filename
13061 512 8 13581 350d video/fbdev/aty/aty128fb.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Maik Broemme <mbroemme@libmpq.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
17534 1824 48 19406 4bce video/fbdev/aty/atyfb_base.o
File size after adding 'const':
text data bss dec hex filename
18686 672 48 19406 4bce video/fbdev/aty/atyfb_base.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Maik Broemme <mbroemme@libmpq.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
19709 5024 32 24765 60bd video/fbdev/aty/radeon_base.o
File size after adding 'const':
text data bss dec hex filename
22893 1840 32 24765 60bd video/fbdev/aty/radeon_base.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Maik Broemme <mbroemme@libmpq.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The vdisplay variable is now only accessed inside of an #ifdef, producing
a harmless warning:
drivers/video/fbdev/aty/atyfb_base.c: In function 'aty_var_to_crtc':
drivers/video/fbdev/aty/atyfb_base.c:805:19: error: unused variable 'vdisplay' [-Werror=unused-variable]
This moves the declaration into the ifdef as well.
Fixes: dd7d958ae9 ("video: fbdev: aty: remove useless variable assignments in aty_var_to_crtc()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Value assigned to variable vdisplay at line 990 is overwritten
at line 1039 before it can be used. Also, variable assignment
at line 987 is the same as at line 1039. This makes such
variable assignments useless.
Remove these variable assignments and the code related.
Addresses-Covertity-ID: 1226900
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Mikulas Patocka
Jia-Ju Bai
Gustavo A. R. Silva
Colin Ian King
Mathieu Malaterre
Arnd Bergmann
Linus Torvalds
Kees Cook
Gustavo A. R. Silva
Greg Kroah-Hartman
Vladis Dronov
Bhumika Goyal
Arvind Yadav