linux/linux-apfs
1
0 Fork 0
mirror of https://github.com/linux-apfs/linux-apfs.git synced 2026-08-18 02:22:47 -07:00
Code Issues Packages Projects Releases Wiki Activity
798,969 Commits 2 Branches 0 Tags
readwrite
Commit Graph
3096 Commits
Author SHA1 Message Date
Jörgen Storvist 28a86092b1 USB: serial: option: add Telit LN940 series 
Added USB serial option driver support for Telit LN940 series cellular
modules. Covering both QMI and MBIM modes.

usb-devices output (0x1900):
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=1900 Rev=03.10
S:  Manufacturer=Telit
S:  Product=Telit LN940 Mobile Broadband
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option

usb-devices output (0x1901):
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 20 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=1901 Rev=03.10
S:  Manufacturer=Telit
S:  Product=Telit LN940 Mobile Broadband
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim

Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
 2018-12-13 20:08:00 +01:00
Jörgen Storvist 3036022444 USB: serial: option: add Fibocom NL668 series 
Added USB serial option driver support for Fibocom NL668 series cellular
modules. Reserved USB endpoints 4, 5 and 6 for network + ADB interfaces.

usb-devices output (QMI mode)
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1508 ProdID=1001 Rev=03.18
S:  Manufacturer=Nodecom NL668 Modem
S:  Product=Nodecom NL668-CN Modem
S:  SerialNumber=
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)

usb-devices output (ECM mode)
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1508 ProdID=1001 Rev=03.18
S:  Manufacturer=Nodecom NL668 Modem
S:  Product=Nodecom NL668-CN Modem
S:  SerialNumber=
C:  #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I:  If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)

Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
 2018-12-13 11:24:58 +01:00
Jörgen Storvist cc6730df08 USB: serial: option: add Simcom SIM7500/SIM7600 (MBIM mode) 
Added USB serial option driver support for Simcom SIM7500/SIM7600 series
cellular modules exposing MBIM interface (VID 0x1e0e,PID 0x9003)

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 14 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1e0e ProdID=9003 Rev=03.18
S:  Manufacturer=SimTech, Incorporated
S:  Product=SimTech, Incorporated
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 6 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim

Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
 2018-12-12 17:13:39 +01:00
Jörgen Storvist 70a7444c55 USB: serial: option: add GosunCn ZTE WeLink ME3630 
Added USB serial option driver support for GosunCn ZTE WeLink ME3630
series cellular modules for USB modes ECM/NCM and MBIM.

usb-devices output MBIM mode:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=0602 Rev=03.18
S:  Manufacturer=Android
S:  Product=Android
S:  SerialNumber=
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim

usb-devices output ECM/NCM mode:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1476 Rev=03.18
S:  Manufacturer=Android
S:  Product=Android
S:  SerialNumber=
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I:  If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether

Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
 2018-12-12 17:13:38 +01:00
Tore Anderson d57ec3c83b USB: serial: option: add HP lt4132 
The HP lt4132 is a rebranded Huawei ME906s-158 LTE modem.

The interface with protocol 0x16 is "CDC ECM & NCM" according to the *.inf
files included with the Windows driver. Attaching the option driver to it
doesn't result in a /dev/ttyUSB* device being created, so I've excluded it.
Note that it is also excluded for corresponding Huawei-branded devices, cf.
commit d544db293a ("USB: support new huawei devices in option.c").

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  3
P:  Vendor=03f0 ProdID=a31d Rev=01.02
S:  Manufacturer=HP Inc.
S:  Product=HP lt4132 LTE/HSPA+ 4G Module
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=2mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option
I:  If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  3
P:  Vendor=03f0 ProdID=a31d Rev=01.02
S:  Manufacturer=HP Inc.
S:  Product=HP lt4132 LTE/HSPA+ 4G Module
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=2mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option
I:  If#=0x6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  3
P:  Vendor=03f0 ProdID=a31d Rev=01.02
S:  Manufacturer=HP Inc.
S:  Product=HP lt4132 LTE/HSPA+ 4G Module
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 3 Cfg#= 3 Atr=a0 MxPwr=2mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option

Signed-off-by: Tore Anderson <tore@fud.no>
Cc: stable@vger.kernel.org
[ johan: drop id defines ]
Signed-off-by: Johan Hovold <johan@kernel.org>
 2018-12-10 09:59:00 +01:00
Johan Hovold f51ccf4621 USB: serial: console: fix reported terminal settings 
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.

Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.

Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().

Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.

This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).

Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org>	# 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
 2018-12-05 11:29:10 +01:00
Linus Torvalds 9703fc8caf Merge tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb 
Pull USB/PHY updates from Greg KH:
 "Here is the big USB/PHY driver patches for 4.20-rc1

  Lots of USB changes in here, primarily in these areas:

   - typec updates and new drivers

   - new PHY drivers

   - dwc2 driver updates and additions (this old core keeps getting
     added to new devices.)

   - usbtmc major update based on the industry group coming together and
     working to add new features and performance to the driver.

   - USB gadget additions for new features

   - USB gadget configfs updates

   - chipidea driver updates

   - other USB gadget updates

   - USB serial driver updates

   - renesas driver updates

   - xhci driver updates

   - other tiny USB driver updates

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
  usb: phy: ab8500: silence some uninitialized variable warnings
  usb: xhci: tegra: Add genpd support
  usb: xhci: tegra: Power-off power-domains on removal
  usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
  usbip: tools: fix atoi() on non-null terminated string
  USB: misc: appledisplay: fix backlight update_status return code
  phy: phy-pxa-usb: add a new driver
  usb: host: add DT bindings for faraday fotg2
  usb: host: ohci-at91: fix request of irq for optional gpio
  usb/early: remove set but not used variable 'remain_length'
  usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
  usb: typec: tcpm: Report back negotiated PPS voltage and current
  USB: core: remove set but not used variable 'udev'
  usb: core: fix memory leak on port_dev_path allocation
  USB: net2280: Remove ->disconnect() callback from net2280_pullup()
  usb: dwc2: disable power_down on rockchip devices
  usb: gadget: udc: renesas_usb3: add support for r8a77990
  dt-bindings: usb: renesas_usb3: add bindings for r8a77990
  usb: gadget: udc: renesas_usb3: Add r8a774a1 support
  USB: serial: cypress_m8: remove set but not used variable 'iflag'
  ...
 2018-10-26 08:14:13 -07:00
Linus Torvalds 44adbac8f7 Merge branch 'work.tty-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs 
Pull tty ioctl updates from Al Viro:
 "This is the compat_ioctl work related to tty ioctls.

  Quite a bit of dead code taken out, all tty-related stuff gone from
  fs/compat_ioctl.c. A bunch of compat bugs fixed - some still remain,
  but all more or less generic tty-related ioctls should be covered
  (remaining issues are in things like driver-private ioctls in a pcmcia
  serial card driver not getting properly handled in 32bit processes on
  64bit host, etc)"

* 'work.tty-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (53 commits)
  kill TIOCSERGSTRUCT
  change semantics of ldisc ->compat_ioctl()
  kill TIOCSER[SG]WILD
  synclink_gt(): fix compat_ioctl()
  pty: fix compat ioctls
  compat_ioctl - kill keyboard ioctl handling
  gigaset: add ->compat_ioctl()
  vt_compat_ioctl(): clean up, use compat_ptr() properly
  gigaset: don't try to printk userland buffer contents
  dgnc: don't bother with (empty) stub for TCXONC
  dgnc: leave TIOC[GS]SOFTCAR to ldisc
  remove fallback to drivers for TIOCGICOUNT
  dgnc: break-related ioctls won't reach ->ioctl()
  kill the rest of tty COMPAT_IOCTL() entries
  dgnc: TIOCM... won't reach ->ioctl()
  isdn_tty: TCSBRK{,P} won't reach ->ioctl()
  kill capinc_tty_ioctl()
  take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()
  synclink: reduce pointless checks in ->ioctl()
  complete ->[sg]et_serial() switchover
  ...
 2018-10-24 14:43:41 +01:00
Greg Kroah-Hartman 89303c7ea7 Merge tag 'usb-serial-4.20-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next 
Johan writes:

USB-serial updates for v4.20-rc1

Here are the USB-serial updates for 4.20-rc1, including:

 - support for CBUS GPIO on FTDI devices (FTX and FT232R)
 - fix of a long-standing transfer-length bug

Included are also various clean ups.

All have been in linux-next with no reported issues.

Signed-off-by: Johan Hovold <johan@kernel.org>

* tag 'usb-serial-4.20-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: cypress_m8: remove set but not used variable 'iflag'
  USB: serial: cypress_m8: fix interrupt-out transfer length
  USB: serial: ftdi_sio: add support for FT232R CBUS gpios
  USB: serial: ftdi_sio: fix gpio name collisions
  USB: serial: ftdi_sio: implement GPIO support for FT-X devices
  USB: serial: cypress_m8: fix spelling mistake "retreiving" -> "retrieving"
 2018-10-18 14:59:04 +02:00
Al Viro 930236a308 complete ->[sg]et_serial() switchover 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:43 -04:00
Al Viro 15cc7bad48 usb_wwan: switch to ->[sg]et_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:42 -04:00
Al Viro fc6cc979e4 whiteheat: switch to ->get_serial() 
... and fix the return value - on success it used to have ioctl(2)
fill the user-supplied struct serial_struct and return -ENOTTY.

Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:42 -04:00
Al Viro 57e5723611 ti_usb_3410_5052: switch to ->[sg]et_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:41 -04:00
Al Viro ee08cefbb5 ssu100: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:41 -04:00
Al Viro 8fbde7984e quatech2: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:40 -04:00
Al Viro 9326ec59ec pl2303: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:40 -04:00
Al Viro 30296aa419 opticon: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:39 -04:00
Al Viro b27ef409b4 mos7840: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:39 -04:00
Al Viro 7cf3e600a0 mos7720: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:38 -04:00
Al Viro 2a5357e563 io_ti: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:38 -04:00
Al Viro e27235eda5 io_edgeport: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:37 -04:00
Al Viro 3ae36bed3a fdti_sio: switch to ->[sg]et_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:37 -04:00
Al Viro c8f97e77d5 f81534: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:36 -04:00
Al Viro 056abede09 f81232: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:35 -04:00
Al Viro aadcd0a178 ark3116: switch to ->get_serial() 
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
 2018-10-13 00:50:35 -04:00