The bug would let the usb controller enter partial power down,
which was formally known as hibernate, upon boot if nothing was plugged
in to the port. Partial power down couldn't be exited properly, so any
usb devices plugged in after boot would not be usable.
Before the name change, params.hibernation was false by default, so
_dwc2_hcd_suspend() would skip entering hibernation. With the
rename, _dwc2_hcd_suspend() was changed to use params.power_down
to decide whether or not to enter partial power down.
Since params.power_down is non-zero by default, it needs to be set
to 0 for rockchip devices to restore functionality.
This bug was reported in the linux-usb thread:
REGRESSION: usb: dwc2: USB device not seen after boot
The commit that caused this regression is:
6d23ee9caa
Signed-off-by: SolidHal <hal@halemmerich.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on stm32f4x9_fsotg since commit
e35b135055 ("usb: dwc2: Add support for STM32F429/439/469 USB OTG
HS/FS in FS mode (internal PHY)"). That commit is pretty recent, so
it's unclear to me why the uframe scheduler was left off. Hopefully
it's because someone copied it from other parameters and didn't think
to try it?
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on Amlogic since commit f94310ac07
("usb: dwc2: add support for Meson8b and GXBB SoCs"). While this was
after most of the recent improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler"), presumably
the parameters were copied from another platform and the uframe
scheduler wasn't tried.
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on HiSilicon since commit
37dd9d65cc ("usb: dwc2: add support of hi6220"). Since then there
have been many many improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler")
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on Broadcom since commit
58b179dcf2 ("staging: dwc2: disable uframe_sched on the bcm2835").
Since then there have been many many improvements, notably the commit
9f9f09b048 ("usb: dwc2: host: Totally redo the microframe
scheduler")
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added hsotg argument to dwc2_readl/writel function prototype,
and also instead of address pass offset of register.
hsotg will contain flag field for endianness.
Also customized dwc2_set_bit and dwc2_clear_bit function for
dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When _param is unsigned and the minimum value of range is 0, it gives
the following warning:
COVERITY NO_EFFECT: This less-than-zero comparison of an unsigned value
is never true.
Converting ._param to int to avoid this warning.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 4.17-rc, commit 03ea6d6e9e ("usb: dwc2: Enable power down")
caused the HiKey board to not correctly handle switching between
usb-gadget and usb-host mode.
Unplugging the OTG port would result in:
[ 42.240973] dwc2 f72c0000.usb: dwc2_restore_host_registers: no host registers to restore
[ 42.249066] dwc2 f72c0000.usb: dwc2_host_exit_hibernation: failed to restore host registers
And the USB-host ports would not function.
And plugging in the OTG port, we would see:
[ 46.046557] WARNING: CPU: 3 PID: 6 at drivers/usb/dwc2/gadget.c:260 dwc2_hsotg_init_fifo+0x194/0x1a0
[ 46.055761] CPU: 3 PID: 6 Comm: kworker/u16:0 Not tainted 4.17.0-rc5-00030-ge67da8c #231
[ 46.055767] Hardware name: HiKey Development Board (DT)
[ 46.055784] Workqueue: dwc2 dwc2_conn_id_status_change
...
Thus, this patch sets the hisi params to disable the power_down
flag by default, and gets thing working again.
Cc: John Youn <johnyoun@synopsys.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Artur Petrosyan <arturp@synopsys.com>
Cc: Grigor Tovmasyan <tovmasya@synopsys.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_IPG_ISOC_SUPPORTED and DCFG_IPG_ISOC_SUPPORDED
bits definitions to enable/disable IPG feature.
Added ipg_isoc_en core parameter which will indicate IPG support
enable/disable and initialize it.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe writes:
usb: changes for v4.17 merge window
Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:
Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.
Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.
We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.
We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).
Apart from these, we have our regular set of non-critical fixes all
over the place.
If the dr_mode is USB_DR_MODE_OTG, forcing the mode is needed during
driver probe to get the host and device specific HW parameters. Then we
clear the force mode bits so that the core operates in OTG mode.
The force mode bits should not be touched at any other time during the
driver lifetime and they should be preserved whenever the GUSBCFG
register is written to. The force mode bit values will persist across
soft resets of the core.
If the dr_mode is either USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL, the
force mode is set just once at probe to configure the core as either a
host or peripheral.
Given the above, we no longer need any other reset delays, force delays,
or any forced modes anywhere else in the driver. So replace all calls to
dwc2_core_reset_and_force_dr_mode() with dwc2_core_reset() and remove
all other unnecessary delays.
Also remove the dwc2_force_mode_if_needed() function since the "if
needed" part is already taken care of by the polling in
dwc2_force_mode().
Finally, remove all other calls to dwc2_clear_force_mode().
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add parameter and it's initialization, needed for hibernation.
Reimplement dwc2_set_param_power_down() to support hibernation too.
Now 'power_down' parameter can be initialized with 0, 1 or 2.
0 - No
1 - Partial power down
2 - Hibernation
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No-op change, only rename.
This code was misnamed originally. It was only responsible for partial
power down and not for hibernation.
Rename core_params->hibernation to core_params->power_down,
dwc2_set_param_hibernation() to dwc2_set_param_power_down().
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add lpm, lpm_clock_gating, besl, hird_threshold_en and hird_threshold
core parameters. These will indicate LPM and LPM Errata support
as well as chosen L1 sleeping mode for the core and PHY.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added function for supporting Active Clock Gating functionality
in the driver.
PCGCCTL1 (Power and Clock Control) register will be used
for controlling the core`s active clock gating feature, and
the previously reserved 12th bit in GHWCFG4 now indicates that the
controller supports the Dynamic Power Reduction (Active Clock Gating)
during no traffic scenarios such as L0, idle, resume and suspend
states.
dwc2_enable_acg() function sets GATEEN bit in PCGCCTL1 register
and enables ACG, if it supported.
According to ACG functional specification, enabling of ACG feature
in host mode done in host initialization, before turning Vbus on,
specifically in dwc2_core_host_init function.
Enabling of ACG feature in device mode done in device initialization,
before clearing the SftDiscon bit in DCTL.
This bit was cleared in dwc2_hsotg_core_connect() function.So
dwc2_enable_acg() called before dwc2_core_connect() calls.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In host mode reading from DPTXSIZn returning invalid value in
dwc2_check_param_tx_fifo_sizes function.
In total TxFIFO size calculations unnecessarily reducing by ep_info.
hw->total_fifo_size can be fully allocated for FIFO's.
Added num_dev_in_eps member in dwc2_hw_params structure to save number
of IN EPs.
Added g_tx_fifo_size array in dwc2_hw_params structure to store power
on reset values of DPTXSIZn registers in forced device mode.
Updated dwc2_hsotg_tx_fifo_count() function to get TxFIFO count from
num_dev_in_eps.
Updated dwc2_get_dev_hwparams() function to store DPTXFSIZn in
g_tx_fifo_size array.
dwc2_get_host/dev_hwparams() functions call moved after num_dev_in_eps
set from hwcfg4.
Modified dwc2_check_param_tx_fifo_sizes() function to check TxFIFOn
sizes based on g_tx_fifo_size array.
Removed ep_info subtraction during calculation of tx_addr_max in
dwc2_hsotg_tx_fifo_total_depth() function. Also removed
dwc2_hsotg_ep_info_size() function as no more need.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary
overcurrent error which would then disable the host port.
This patch uses the standard 'disable-over-current' binding to allow of the
option of disabling the over-current condition.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
SolidHal
Grigor Tovmasyan
Douglas Anderson
Gevorg Sahakyan
John Stultz
Greg Kroah-Hartman
Vardan Mikayelyan
John Youn
Sevak Arakelyan
Razmik Karapetyan
Gevorg Sahakyan
Amelie Delaunay
Minas Harutyunyan
Dinh Nguyen