Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot and KASAN found the following invalid-free bug in
port_over_current_notify():
--------------------------------------------------------------------------
BUG: KASAN: double-free or invalid-free in port_over_current_notify
drivers/usb/core/hub.c:5192 [inline]
BUG: KASAN: double-free or invalid-free in port_event
drivers/usb/core/hub.c:5241 [inline]
BUG: KASAN: double-free or invalid-free in hub_event+0xd97/0x4140
drivers/usb/core/hub.c:5384
CPU: 1 PID: 32710 Comm: kworker/1:3 Not tainted 4.20.0-rc3+ #129
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256
kasan_report_invalid_free+0x64/0xa0 mm/kasan/report.c:336
__kasan_slab_free+0x13a/0x150 mm/kasan/kasan.c:501
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kfree+0xcf/0x230 mm/slab.c:3817
port_over_current_notify drivers/usb/core/hub.c:5192 [inline]
port_event drivers/usb/core/hub.c:5241 [inline]
hub_event+0xd97/0x4140 drivers/usb/core/hub.c:5384
process_one_work+0xc90/0x1c40 kernel/workqueue.c:2153
worker_thread+0x17f/0x1390 kernel/workqueue.c:2296
kthread+0x35a/0x440 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
--------------------------------------------------------------------------
The problem is caused by use of a static array to store
environment-string pointers. When the routine is called by multiple
threads concurrently, the pointers from one thread can overwrite those
from another.
The solution is to use an ordinary automatic array instead of a static
array.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+98881958e1410ec7e53c@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.
Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.
Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.
This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Raydium USB touchscreen fails to set config if LPM is enabled:
[ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.030660] usb 1-8: Product: Raydium Touch System
[ 2.030661] usb 1-8: Manufacturer: Raydium Corporation
[ 7.132209] usb 1-8: can't set config #1, error -110
Same behavior can be observed on 2386:3114.
Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[ 206.143691] usb 3-2.4: device descriptor read/64, error -32
[ 206.351671] usb 3-2.4: device descriptor read/64, error -32
Info for this hub:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1a40 ProdID=0101 Rev=01.11
S: Product=USB 2.0 Hub
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.
Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting
added to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
usb: phy: ab8500: silence some uninitialized variable warnings
usb: xhci: tegra: Add genpd support
usb: xhci: tegra: Power-off power-domains on removal
usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
usbip: tools: fix atoi() on non-null terminated string
USB: misc: appledisplay: fix backlight update_status return code
phy: phy-pxa-usb: add a new driver
usb: host: add DT bindings for faraday fotg2
usb: host: ohci-at91: fix request of irq for optional gpio
usb/early: remove set but not used variable 'remain_length'
usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
usb: typec: tcpm: Report back negotiated PPS voltage and current
USB: core: remove set but not used variable 'udev'
usb: core: fix memory leak on port_dev_path allocation
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
USB: serial: cypress_m8: remove set but not used variable 'iflag'
...
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
Commit 7a68d9fb85 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs. However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer. (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)
This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes: 7a68d9fb85 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/core/driver.c: In function 'usb_driver_claim_interface':
drivers/usb/core/driver.c:513:21: warning:
variable 'udev' set but not used [-Wunused-but-set-variable]
Since commit c183813fce ("USB: remove LPM management from
usb_driver_claim_interface()"), 'udev' is not used.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the allocation of port_dev_path from the call to
kobject_get_path is not being kfree'd, causing a memory leak. Fix
this by kfree'ing this at the end of the function. Add an extra
error exit path to fix one of the early leaks when envp[0] fails
to be allocated.
Detected by CoverityScan, CID#1473771 ("Resource Leak")
Fixes: 201af55da8 ("usb: core: added uevent for over-current")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus recently observed that if we did not worry about the padding
member in struct siginfo it is only about 48 bytes, and 48 bytes is
much nicer than 128 bytes for allocating on the stack and copying
around in the kernel.
The obvious thing of only adding the padding when userspace is
including siginfo.h won't work as there are sigframe definitions in
the kernel that embed struct siginfo.
So split siginfo in two; kernel_siginfo and siginfo. Keeping the
traditional name for the userspace definition. While the version that
is used internally to the kernel and ultimately will not be padded to
128 bytes is called kernel_siginfo.
The definition of struct kernel_siginfo I have put in include/signal_types.h
A set of buildtime checks has been added to verify the two structures have
the same field offsets.
To make it easy to verify the change kernel_siginfo retains the same
size as siginfo. The reduction in size comes in a following change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The platform firmware "location" data is used to find port peer
relationships. But firmware is an unreliable source, and there are
real world examples of errors leading to missing or wrong peer
relationships. Debugging this is currently hard.
Exporting the location attribute makes it easier to spot mismatches
between the firmware data and the real world.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new scheme is required just to support legacy low and full-speed
devices. For high speed devices, it will slower the enumeration speed.
So in this patch we try the "old" enumeration scheme first for high speed
devices, and this is what Windows does since Windows 8.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 1cbd53c8cd ("usb: core: introduce per-port over-current
counters") usb ports expose a sysfs value 'over_current_count'
to user space. This value on its own is not very useful as it requires
manual polling.
As a solution, fire a udev event from the usb hub device that specifies
the values 'OVER_CURRENT_PORT' and 'OVER_CURRENT_COUNT' that indicate
the path of the usb port where the over-current event occurred and the
value of 'over_current_count' in sysfs. Additionally, call
sysfs_notify() so the sysfs value supports poll().
Signed-off-by: Jon Flatley <jflat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applying dynamic usbcore quirks in early booting when the slab is
not yet ready would cause kernel panic of null pointer dereference
because the quirk_count has been counted as 1 while the quirk_list
was failed to allocate.
i.e.,
[ 1.044970] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1.044995] IP: [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
[ 1.045016] PGD 0
[ 1.045026] Oops: 0000 [#1] PREEMPT SMP
[ 1.046986] gsmi: Log Shutdown Reason 0x03
[ 1.046995] Modules linked in:
[ 1.047008] CPU: 0 PID: 81 Comm: kworker/0:3 Not tainted 4.4.154 #28
[ 1.047016] Hardware name: Google Coral/Coral, BIOS Google_Coral.10068.27.0 12/04/2017
[ 1.047028] Workqueue: usb_hub_wq hub_event
[ 1.047037] task: ffff88017a321c80 task.stack: ffff88017a384000
[ 1.047044] RIP: 0010:[<ffffffffb0953ec7>] [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
To tackle this odd, let's balance the quirk_count to 0 when the kcalloc
call fails, and defer the quirk setting into a lower level callback
which ensures that the kernel memory management has been initialized.
Fixes: 027bd6cafd ("usb: core: Add "quirks" parameter for usbcore")
Signed-off-by: Harry Pan <harry.pan@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB audio class 3.0 specification introduced many significant
changes like
- new power domains, support for LPM/L1
- new cluster descriptor
- new high capability and class-specific string descriptors
- BADD profiles
- ... and many other things (check spec from link below:
http://www.usb.org/developers/docs/devclass_docs/USB_Audio_v3.0.zip)
Now that UAC3 is supported in linux, choose UAC3
configuration for audio if the device supports it.
Selecting this configuration will enable the system to
save power by leveraging the new power domains and LPM L1
capability and also support new codec types and data formats
for consumer audio applications.
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_find_alt_setting() takes a pointer to a struct usb_host_config as
an argument; it searches for an interface with specified interface and
alternate setting numbers in that config. However, it crashes if the
usb_host_config pointer argument is NULL.
Since this is a general-purpose routine, available for use in many
places, we want to to be more robust. This patch makes it return NULL
whenever the config argument is NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+19c3aaef85a89d451eac@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzing project found a use-after-free bug in the USB
core. The bug was caused by usbfs not unbinding from an interface
when the USB device file was closed, which led another process to
attempt the unbind later on, after the private data structure had been
deallocated.
The reason usbfs did not unbind the interface at the appropriate time
was because it thought the interface had never been claimed in the
first place. This was caused by the fact that
usb_driver_claim_interface() does not clean up properly when
device_bind_driver() returns an error. Although the error code gets
passed back to the caller, the iface->dev.driver pointer remains set
and iface->condition remains equal to USB_INTERFACE_BOUND.
This patch adds proper error handling to usb_driver_claim_interface().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+f84aa7209ccec829536f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_driver_claim_interface() disables and re-enables Link Power
Management, but it shouldn't do either one, for the reasons listed
below. This patch removes the two LPM-related function calls from the
routine.
The reason for disabling LPM in the analogous function
usb_probe_interface() is so that drivers won't have to deal with
unwanted LPM transitions in their probe routine. But
usb_driver_claim_interface() doesn't call the driver's probe routine
(or any other callbacks), so that reason doesn't apply here.
Furthermore, no driver other than usbfs will ever call
usb_driver_claim_interface() unless it is already bound to another
interface in the same device, which means disabling LPM here would be
redundant. usbfs doesn't interact with LPM at all.
Lastly, the error return from usb_unlocked_disable_lpm() isn't handled
properly; the code doesn't clean up its earlier actions before
returning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8306095fd2 ("USB: Disable USB 3.0 LPM in critical sections.")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we filter flags before they reach the core we need to generate our
own warnings.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 0cb54a3e47 ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting a ZERO_PACKET or not is sensible only for output.
In the input direction the device decides.
Likewise accepting short packets makes sense only for input.
This allows operation with panic_on_warn without opening up
a local DOS.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+843efa30c8821bd69f53@syzkaller.appspotmail.com
Fixes: 0cb54a3e47 ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Payer
Harry Pan
Alan Stern
Michael Niewöhner
Dennis Wassenberg
Kai-Heng Feng
Emmanuel Pescosta
Linus Torvalds
YueHaibing
Colin Ian King
Eric W. Biederman
Bjørn Mork
Zeng Tao
Greg Kroah-Hartman
Jon Flatley
Saranya Gopal
Oliver Neukum