Commit f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode
again") makes a change to FIFO clearing code which its commit message
suggests was intended to be specific to use with RS485 mode, however:
1) The change made does not just affect __do_stop_tx_rs485(), it also
affects other uses of serial8250_clear_fifos() including paths for
starting up, shutting down or auto-configuring a port regardless of
whether it's an RS485 port or not.
2) It makes the assumption that resetting the FIFOs is a no-op when
FIFOs are disabled, and as such it checks for this case & explicitly
avoids setting the FIFO reset bits when the FIFO enable bit is
clear. A reading of the PC16550D manual would suggest that this is
OK since the FIFO should automatically be reset if it is later
enabled, but we support many 16550-compatible devices and have never
required this auto-reset behaviour for at least the whole git era.
Starting to rely on it now seems risky, offers no benefit, and
indeed breaks at least the Ingenic JZ4780's UARTs which reads
garbage when the RX FIFO is enabled if we don't explicitly reset it.
3) By only resetting the FIFOs if they're enabled, the behaviour of
serial8250_do_startup() during boot now depends on what the value of
FCR is before the 8250 driver is probed. This in itself seems
questionable and leaves us with FCR=0 & no FIFO reset if the UART
was used by 8250_early, otherwise it depends upon what the
bootloader left behind.
4) Although the naming of serial8250_clear_fifos() may be unclear, it
is clear that callers of it expect that it will disable FIFOs. Both
serial8250_do_startup() & serial8250_do_shutdown() contain comments
to that effect, and other callers explicitly re-enable the FIFOs
after calling serial8250_clear_fifos(). The premise of that patch
that disabling the FIFOs is incorrect therefore seems wrong.
For these reasons, this reverts commit f6aa5beb45 ("serial: 8250: Fix
clearing FIFOs in RS485 mode again").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode again").
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # 4.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a25 ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a25 ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling")
Signed-off-by: Peter Shih <pihsun@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the DT-related settings are split out to
uniphier_of_serial_setup(), but it turned out to be not nice.
The next commit will add a DT property, but it will not fit in
the helper. Merge the helper into the probe function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FIFO size of the UART devices is 64 on almost all UniPhier SoCs
with the exception Pro4TV SoC (MN2WS0235), which used 128 FIFO size.
However, Pro4TV SoC was never upstreamed, and out of production.
So, this property has never been used in a useful way.
Let's remove old unused code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 FIFOs indeed need to be cleared after stopping transmission in
RS485 mode without SER_RS485_RX_DURING_TX flag set. But there are two
problems with the approach taken by the previous patch from Fixes tag.
First, serial8250_clear_fifos() should clear fifos, but what it really
does is it enables the FIFOs unconditionally if present, clears them
and then sets the FCR register to zero, which effectively disables the
FIFOs. In case the FIFO is disabled, enabling it and clearing it makes
no sense and in fact can trigger misbehavior of the 8250 core. Moreover,
the FCR register may contain other FIFO configuration bits which may not
be writable unconditionally and writing them incorrectly can trigger
misbehavior of the 8250 core too. (ie. AM335x UART swallows the first
byte and retransmits the last byte twice because of this FCR write).
Second, serial8250_clear_and_reinit_fifos() completely reloads the FCR,
but what really has to happen at the end of the RS485 transmission is
clearing of the FIFOs and nothing else.
This patch repairs serial8250_clear_fifos() so that it really only
clears the FIFOs by operating on FCR[2:1] bits and leaves all the
other bits alone. It also undoes serial8250_clear_and_reinit_fifos()
from __do_stop_tx_rs485() as serial8250_clear_fifos() is sufficient.
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: 2bed8a8e70 ("Clearing FIFOs in RS485 emulation mode causes subsequent transmits to break")
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # let it bake a bit before merging
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c58caaab3b ("serial: 8250: of: Defer probe on missing IRQ"), a
check was added for the UART driver being probed prior to the parent IRQ
controller.
Unfortunately this breaks certain boards which have no interrupt support,
like Huawei D03.
Indeed, the 8250 DT bindings state that interrupts should be supported -
not must.
To fix, switch from irq_of_parse_and_map() to of_irq_get(), which
does relay whether the IRQ host controller domain is not ready, i.e.
defer probe, instead of assuming it.
Fixes: c58caaab3b ("serial: 8250: of: Defer probe on missing IRQ")
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The printk() in serial8250_interrupt() was once hidden behind a debug
macro in commit f4f653e987 ("serial: 8250, disable "too much work"
messages") and reverted back in commit 12de375ec4 ("Revert "serial:
8250, disable "too much work" messages"").
This was introduced first in 0.99.13k with the "serial" driver itself
(and called pass_number with a limit of 64 and no print). In 1.1.13 it
was renamed to pass_counter and the printk was behind #if 0. In 1.1.94
the limit of 64 was increased to 256 and hidden behind
RS_ISR_PASS_LIMIT. With this change the #if 0 turned into #if 1. It
slowly become what we have today with a loop limit of 512.
Usually, that printk isn't hit. However on KVM with a busy UART and
overloaded host it might happen. It is also likely with threaded
interrupts and a task which preempts the interrupt handler.
If the UART has (legitimate) work to do and we break out of the loop,
nothing changes: the interrupt is most likely already pending in the
interrupt controller and we end up in the handler anyway. This printk is
hardly helping.
Older kernels also had a comment saying that a bad configuration might
lead to this but I don't see how that should happen because a wrongly
configured interrupt number would let the handler leave "early" with
IRQ_NONE and the spurious detected will handle that (weill since 2.6.11,
before that we had no spurious detector). In that case, we would never
loop that often here.
This loop looks like an optimisation in order to pull the bytes from the
FIFO which were received while we were already here instead of waiting
for the interrupt. This might have been a good idea while the CPUs were
slow and FIFOs small.
There are other serial driver in tree, like the amba-pl*, which also
have this kind of a loop but without the printk (and were based on this
driver).
Remove the printk which might trigger in otherwise valid situtations.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Revert commit ecb988a3b7: tty: serial:
8250: 8250_core: NXP SC16C2552 workaround
The above commit causes userland application to no longer write
correctly its first write to a dumb terminal connected to /dev/ttyS0.
This commit seems to be the culprit. It's as though the TX FIFO is being
reset during that write. What should be displayed is:
PSW 80000000 INST 00000000 HALT
//
What is displayed is some variation of:
T 00000000 HAL//
Reverting this commit via this patch fixes my problem.
Signed-off-by: Mark Hounschell <dmarkh@cfl.rr.com>
Fixes: ecb988a3b7 ("tty: serial: 8250: 8250_core: NXP SC16C2552 workaround")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sleep wake-up refactoring that I introduced in
commit c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
did not account for devices with a slave device on the expansion port.
This patch pokes the INT0 register in the slave device, if present, in
order to ensure that MSI interrupts don't get permanently "stuck"
because of a sleep wake-up interrupt as described here:
commit 2c0ac5b48a ("serial: exar: Fix stuck MSIs")
This also converts an ioread8() to readb() in order to provide visual
consistency with the MMIO-only accessors used elsewhere in the driver.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Fixes: c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dw8250_set_termios() doesn't set baud rate if the arg "old ktermios" is
NULL. This happens during resume.
Call Trace:
...
[ 54.928108] dw8250_set_termios+0x162/0x170
[ 54.928114] serial8250_set_termios+0x17/0x20
[ 54.928117] uart_change_speed+0x64/0x160
[ 54.928119] uart_resume_port
...
So the baud rate is not restored after S3 and breaks the apps who use
UART, for example, console and bluetooth etc.
We address this issue by setting the baud rate irrespective of arg
"old", just like the drivers for other 8250 IPs. This is tested with
Intel Broxton platform.
Signed-off-by: Chen Hu <hu1.chen@intel.com>
Fixes: 4e26b134bd ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have port name stored in struct uart_port, we better to use
that one instead of open coding.
This will make it one place source for easier maintenance or
modifications.
While here, replace printk_ratelimited(KERN_INFO ) by pr_info_ratelimited().
It seems last printk() call in 8250_port.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Describe all memebers in struct exar8250_board, otherwise we get a warning:
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'has_slave' not described in 'exar8250_board'
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'setup' not described in 'exar8250_board'
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'exit' not described in 'exar8250_board'
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exar UARTs by default supports only up to 8 channels,
all above go as extension. Thus, there is no need to have
an additional property to distinguish them from first ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas RZ/N1 UART is based on the Synopsys DW UART, but has additional
registers for DMA. This patch does not address the changes required for DMA
support, it simply adds the compatible string.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the IRQ controller is not yet probed do not proceed with irq=0,
try to defer the probe.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a
valid divisor latch fraction register. The fractional divisor width is
4bits ~ 6bits.
Now the preparation is done, it's easy to add the feature support.
This patch firstly tries to get the fractional divisor width during
probe, then setups dw specific get_divisor() and set_divisor() hook.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Burton
Peter Shih
Greg Kroah-Hartman
Guenter Roeck
Dai Okamura
Masahiro Yamada
Marek Vasut
John Garry
Lokesh Vutla
Sebastian Andrzej Siewior
Linus Torvalds
Mark
Aaron Sierra
Srinath Mannam
Chen Hu
Andy Shevchenko
Phil Edworthy
Alexander Sverdlin
Jisheng Zhang