Driver can report IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ so it's
important to provide valid & complete info about supported bands for
each channel. By default no support for 160 MHz should be assumed unless
firmware reports it for a given channel later.
This fixes info passed to the userspace. Without that change userspace
could try to use invalid channel and fail to start an interface.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Previous commit /adding/ support for 160 MHz chanspecs was incomplete.
It didn't set bandwidth info and didn't extract control channel info. As
the result it was also using uninitialized "sb" var.
This change has been tested for two chanspecs found to be reported by
some devices/firmwares:
1) 60/160 (0xee32)
Before: chnum:50 control_ch_num:36
After: chnum:50 control_ch_num:60
2) 120/160 (0xed72)
Before: chnum:114 control_ch_num:100
After: chnum:114 control_ch_num:120
Fixes: 330994e8e8 ("brcmfmac: fix for proper support of 160MHz bandwidth")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Beacons are not updated to reflect TIM changes. This is not compliant with
power-saving client stations as the beacons do not have valid TIM and can
cause the network to stall at random occasions and to have highly variable
latencies.
Fix it by updating beacon templates on mac80211 set_tim callback.
Addresses an issue described in:
https://marc.info/?i=20180911163534.21312d08%20()%20manjaro
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/b43/main.c: In function 'b43_one_core_detach':
drivers/net/wireless/broadcom/b43/main.c:5496:17: warning:
variable 'wl' set but not used [-Wunused-but-set-variable]
After commit 644aa4d620 ("b43: remove list of IEEE 802.11 devices")
'wl' is not used any more.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.
This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.
This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ucode chunk might be relatively large and the allocation with
kmalloc() may fail occasionally. Since the data isn't DMA-transferred
but by manual loops, we can use vmalloc instead of kmalloc.
For a better performance, though, kvmalloc() would be the best choice
in such a case, so let's replace with it.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1103431
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_rxglom':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1466:11: warning:
variable 'sfdoff' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_bus_preinit':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3408:7: warning:
variable 'pad_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
debugfs_remove_recursive has taken IS_ERR_OR_NULL into account. So just
remove the condition check before debugfs_remove_recursive.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When obtaining the firmware capability a buffer is provided of 512
bytes. However, if all features in firmware are supported the buffer
needs to be 565 bytes as otherwise truncated information is retrieved
from firmware. Increasing the buffer to 768 bytes on stack.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 66cffd6daa ("b43: fix transmit failure when VT is switched"),
a condition is noted where the network controller needs to be reset. Note
that this situation happens when running the open-source firmware
(http://netweb.ing.unibs.it/~openfwwf/), plus a number of other special
conditions.
for a different card model, it is reported that this change breaks
operation running the proprietary firmware
(https://marc.info/?l=linux-wireless&m=153504546924558&w=2). Rather
than reverting the previous patch, the code is tweaked to avoid the
reset unless the open-source firmware is being used.
Fixes: 66cffd6daa ("b43: fix transmit failure when VT is switched")
Cc: Stable <stable@vger.kernel.org> # 4.18+
Cc: Taketo Kabe <kabe@sra-tohoku.co.jp>
Reported-and-tested-by: D. Prabhu <d.praabhu@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of direct SKB list pointer accesses.
In these situations, we absolutely know that the SKB queue in question
is non-empty.
Signed-off-by: David S. Miller <davem@davemloft.net>
strnchr takes arguments in the order of its name: string, max bytes to
read, character to search for. Here we're passing '\n' aka 10 as the
buffer size, and searching for sizeof(buf) aka BRCMF_DCMD_SMLEN aka
256 (aka '\0', since it's implicitly converted to char) within those 10
bytes.
Just interchanging the last two arguments would still leave a bug,
because if we've been successful once, there are not sizeof(buf)
characters left after the new value of p.
Since clmver is immediately afterwards passed as a %s argument, I assume
that it is actually a properly nul-terminated string. For that case, we
have strreplace().
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the unnecessary parentheses to fix the clang warning of
extraneous parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
strncpy might not NUL-terminate the string, if the name equals the buffer size.
Use strlcpy instead.
Signed-off-by: Michael Buesch <m@bues.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
strncpy might not NUL-terminate the string, if the name equals the buffer size.
Use strlcpy instead.
Signed-off-by: Michael Buesch <m@bues.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki
Ali MJ Al-Nasrawy
David S. Miller
YueHaibing
Chung-Hsien Hsu
Colin Ian King
Takashi Iwai
zhong jiang
Arend van Spriel
Larry Finger
Igor Stoppa
Rasmus Villemoes
Jia-Shyr Chuang
Varsha Rao
Michael Büsch