Clang warns:
drivers/net/ethernet/huawei/hinic/hinic_tx.c:392:34: error: implicit
conversion from enumeration type 'enum hinic_l4_tunnel_type' to
different enumeration type 'enum hinic_l4_offload_type'
[-Werror,-Wenum-conversion]
hinic_task_set_tunnel_l4(task, TUNNEL_UDP_NO_CSUM,
~~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~
1 error generated.
It seems that hinic_task_set_tunnel_l4 was meant to take an enum of type
hinic_l4_tunnel_type, not hinic_l4_offload_type, given both the name of
the functions and the values used.
Fixes: cc18a7543d ("net-next/hinic: add checksum offload and TSO support")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checksum offload and TSO support for the HiNIC
driver. Perfomance test (Iperf) shows more than 100% improvement
in TCP streams.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
hinic uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Note that hinic_netpoll() was incorrectly scheduling NAPI
on both RX and TX queues.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem below. The problem can be reproduced by the
following steps:
1) Connecting all HiNIC interfaces
2) On server side
# sudo ifconfig eth0 192.168.100.1 up #Using MLX CX4 card
# iperf -s
3) On client side
# sudo ifconfig eth0 192.168.100.2 up #Using our HiNIC card
# iperf -c 192.168.101.1 -P 10 -t 100000
after hours of testing, we will see errors:
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
The errors are caused by the following problem.
1) The hinic_get_wqe() checks the "wq->delta" to allocate new WQEs:
if (atomic_sub_return(num_wqebbs, &wq->delta) <= 0) {
atomic_add(num_wqebbs, &wq->delta);
return ERR_PTR(-EBUSY);
}
If the WQE occupies multiple pages, the shadow WQE will be used. Then the
hinic_xmit_frame() fills the WQE.
2) While in parallel with 1), the free_tx_poll() checks the "wq->delta"
to free old WQEs:
if ((atomic_read(&wq->delta) + num_wqebbs) > wq->q_depth)
return ERR_PTR(-EBUSY);
There is a probability that the shadow WQE which hinic_xmit_frame() is
using will be damaged by copy_wqe_to_shadow():
if (curr_pg != end_pg) {
void *shadow_addr = &wq->shadow_wqe[curr_pg * wq->max_wqe_size];
copy_wqe_to_shadow(wq, shadow_addr, num_wqebbs, *cons_idx);
return shadow_addr;
}
This can cause WQE data error and you will see the above error messages.
This patch fixes the problem.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise interfaces get exposed under /sys/devices/virtual, which
doesn't give udev the context it needs for PCI-based predictable
interface names.
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calculation of "wqe_size" is not correct when the tx queue is busy in
hinic_xmit_frame().
When there are no free WQEs, the tx flow will unmap the skb buffer, then
ring the doobell for the pending packets. But the "wqe_size" which used
to calculate the doorbell address is not correct. The wqe size should be
cleared to 0, otherwise, it will cause a doorbell error.
This patch fixes the problem.
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer pfhwdev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'pfhwdev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following warning is seen when rmmod hinic. This is because affinity
value is not reset before calling free_irq(). This patch fixes it.
[ 55.181232] WARNING: CPU: 38 PID: 19589 at kernel/irq/manage.c:1608
__free_irq+0x2aa/0x2c0
Fixes: 352f58b0d9 ("net-next/hinic: Set Rxq irq to specific cpu for NUMA")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device IDs to support 25GE and 100GE card:
1. Add device id 0x0201 for HINIC 100GE dual port card.
2. Add device id 0x0200 for HINIC 25GE dual port card.
3. Macro of device id 0x1822 is modified for HINIC 25GE quad port card.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables arm64 platform support for the HINIC driver.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI pool API is deprecated. Replace the PCI pool old API by the
appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Fix the following scenario:
1. tx_free_poll is running on cpu X
2. xmit function is running on cpu Y and fails to get sq wqe
3. tx_free_poll frees wqes on cpu X and checks the queue is not stopped
4. xmit function stops the queue after failed to get sq wqe
5. The queue is stopped forever
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set Rxq irq to specific cpu for allocating and receiving the skb from
the same node.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We probably don't want to enable code supporting particular hardware by
default e.g. when someone does 'make defconfig'. Other ethernet modules
don't do it.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_pad() function frees the skb on error, so this code has a double
free.
Fixes: 00e57a6d4a ("net-next/hinic: Add Tx operation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We never set the error code in this function.
Fixes: eabf0fad81 ("net-next/hinic: Initialize api cmd resources")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions set_ctrl0 and set_ctrl1 are local to the source and do
not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'set_ctrl0' was not declared. Should it be static?
symbol 'set_ctrl1' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Chancellor
Zhao Chen
Eric Dumazet
David S. Miller
dann frazier
Colin Ian King
Wei Yongjun
Kees Cook
Romain Perier
Aviad Krawczyk
Vitaly Kuznetsov
Dan Carpenter